Re: 65Custom Build Thread
Making some nice progress!
|
Re: 65Custom Build Thread
Funny, I put everything back to the original, to mount the chains.
Good progress. |
Re: 65Custom Build Thread
Quote:
|
Re: 65Custom Build Thread
3 Attachment(s)
Work continues
|
Re: 65Custom Build Thread
]ust thinking, when you get roof welded on be sure and check condition of drains. Almost easy to not even notice them and with your replacement of your drip rails it easy to over look. That the cause of your rust in edges of a pillars and over windshield area. Roof water sits rust through and has access to other areas. Took pictures of mine but don’t know how to attach.
|
Re: 65Custom Build Thread
Quote:
|
Re: 65Custom Build Thread
1 Attachment(s)
something else to ponder
|
Re: 65Custom Build Thread
Quote:
|
Re: 65Custom Build Thread
Quote:
|
Re: 65Custom Build Thread
3 Attachment(s)
Making progress getting it mocked up so we know how it is going to work, so far it works as we expected.
|
Re: 65Custom Build Thread
Even though it isn't finished yet, I like that fuel fill door idea a lot
|
Re: 65Custom Build Thread
That looks great, very good idea.
|
Re: 65Custom Build Thread
One of the issues we are running into is the fuel fill is going to have to be a 1.5" fill and to get the hose run we will have to have the flexible fuel hose. Also it will have to go through the rear bed cross member so we will have to cut a notch or hole to connect to the tank
|
Re: 65Custom Build Thread
1 Attachment(s)
This was dropped off the other day.
|
Re: 65Custom Build Thread
5 Attachment(s)
A little update making some progress, fuel door a little further along, reshaped the the wheel well lip it was pretty beat up on both sides, re-welded the inner braces, top of the driver bed side needs to pushed back flat it is some how rolled up a little didn't notice that till we started working on it. Still need a patch at the top of bed side near the fuel door, looks like some one cut it for a piece of plywood to use a tailgate best I can tell both side of the bed have the same cuts, reset the drivers side and started working on the passenger bed side.
|
Re: 65Custom Build Thread
4 Attachment(s)
Test fitted the fuel tank, a before pic of the passenger side wheel well lip and an after of the Driver side wheel well lip, both were a bit rough and how we mounted the fuel door hinge.
|
Re: 65Custom Build Thread
1 Attachment(s)
Test mounted the dummy gas tank fill, want the truck to look fairly original, needs a little adjustment.
|
Re: 65Custom Build Thread
5 Attachment(s)
Making mods to the tailgate, taking three different set of parts to make it work
put in a new bed header panel |
Re: 65Custom Build Thread
4 Attachment(s)
Mount of the catch side of the latch, the tailgate catch and links are made from two different sets of links one to get the right length on the links and the other for the mount, another plate is installed behind the catch to shift the catch and links towards the tailgate to make sure everything clears hopefully doesn't bind or pinch or chip paint when finished,
temporary hole cut for the latch handle |
Re: 65Custom Build Thread
2 Attachment(s)
Any thoughts on how these wheels look to everyone? I was hoping when I purchased these they would look a little more traditional with the front side spacing being inset more as far as the spoke location but they were not and now I see it is mainly due to how the wheel is made best i can determine, anyway let me know what you all think of these, Im thinking they may be replaced and something more traditional looking coming, to me they look like they belong on a late 80's to 90's model
I will say I think look ok here but not really the look I was shooting for and I think it would give a modern look to the truck, if I was doing more mods like flush glass, one piece side windows and smoothed dood handles etc they might look good with it. |
Re: 65Custom Build Thread
Those wheels aren't my faves either. But bear in mind that I went about as far the other way as you can go, 15x8 steelies with chrome hubcaps. So I may not be a good judge.
https://67-72chevytrucks.com/vboard/...1&d=1671216909 |
Re: 65Custom Build Thread
Quote:
these are two piece wheels but not made in a standard way where the center is placed in a hoop and then welded these seem that they are machined from a blank with limited spacing depending on the depth and then welded on to the hoop to make up the width |
Re: 65Custom Build Thread
4 Attachment(s)
Another update, a little more progress
|
Re: 65Custom Build Thread
Looking good. Will you be rewelding the seam on the tailgate?
|
Re: 65Custom Build Thread
Quote:
|
All times are GMT -4. The time now is 10:12 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com