Re: 5.3 swap build so far
Thanks man, it was kinda frustrating
|
Re: 5.3 swap build so far
Quote:
|
Re: 5.3 swap build so far
15? thats it?....i wish that was all i had my cluster out....lol i can pull that thing out in like 1 minute now lol
|
Re: 5.3 swap build so far
Quote:
|
Re: 5.3 swap build so far
Quote:
|
Re: 5.3 swap build so far
|
Re: 5.3 swap build so far
Thanks, did not mean to hijack your thread
|
Re: 5.3 swap build so far
hey u said u used zip ties to secure the pcm?
|
Re: 5.3 swap build so far
ya i used, I'm going to put another one on the back of it, its doing some rattling around in there and i can here it, if i can't get a zip tie in there I'm going to clamp it down
|
Re: 5.3 swap build so far
1 Attachment(s)
how big of a zip tie did u use? I need to secure mine
|
Re: 5.3 swap build so far
Quote:
|
Re: 5.3 swap build so far
you doing dbw?
|
Re: 5.3 swap build so far
I checked the clearance today n its good...I cant move the pcm too much as the wiring is kinda short so where its at there in da pic is as far as I could put it. im running dbc
|
Re: 5.3 swap build so far
still tryin figure out how to mount my fuse block too
|
Re: 5.3 swap build so far
Quote:
|
Re: 5.3 swap build so far
you could make a mount on that corner where all that room is right by your ecu or that green open spot on your firewall
|
Re: 5.3 swap build so far
my buddy was sayin something about using a spacer to mount it...not sure what kinda spacer hes talkin about though
|
Re: 5.3 swap build so far
me either, maybe a spacer to suspend it from the wheel well, but that would get closer to your hood hinges, too bad your wires wasn't longer...youd have more options
|
Re: 5.3 swap build so far
I think I can still mount it on the firewall...ill have to check it again.
|
Re: 5.3 swap build so far
It's interesting to see how y'all are mounting the pcm. I was going to try and mount the oem holder off my 2001 donor onto my fender well... I wish the oem wiring harness was longer so I could mount inside the cab. However, this isn't a show truck so I will mount where ever it will reach too. Would be nice to mount it and make it look just like the 2001 would when you popped the hood.
|
Re: 5.3 swap build so far
I was going to mount mine in the cab on the trans tunnel but I changed my mind...I didn't feel like drilling another big hole in my firewall. I was going to also get the factory pcm mount but then I got the idea from dman1982 to use the plate for the cold air intake to make a mount and its workin out great...saved some cash right there too
|
Re: 5.3 swap build so far
Quote:
|
Re: 5.3 swap build so far
1 Attachment(s)
Getting rid of the speedo cable, had to fill a hole....
|
Re: 5.3 swap build so far
Bud light? I been filling holes with PBR since back in the day! :)
http://i112.photobucket.com/albums/n...hevy/012-9.jpg |
Re: 5.3 swap build so far
Quote:
|
All times are GMT -4. The time now is 10:53 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com