|
Re: LT1 Burbs 65 Stock SW Build
Quote:
|
Re: LT1 Burbs 65 Stock SW Build
Quote:
|
Re: LT1 Burbs 65 Stock SW Build
Quote:
|
Re: LT1 Burbs 65 Stock SW Build
Quote:
|
Re: LT1 Burbs 65 Stock SW Build
Quote:
|
Re: LT1 Burbs 65 Stock SW Build
4 Attachment(s)
Don't be a bonehead like me and check to make sure your fender extensions or cowls, whatever they are called, are not the same side. I got my original Harrison rad recored also.
|
Re: LT1 Burbs 65 Stock SW Build
Quote:
Hope those new bed sides are up to spec. Looking really great. |
Re: LT1 Burbs 65 Stock SW Build
5 Attachment(s)
Cleaning up some odds and sods, went to put the driveshaft in but found it was 1" to long. I bought it from a member on here but I guess it was never installed. I also had to weld up some holes on the inner fender that had been drilled in to move the voltage regulator. Fenders and grille surround should be installed for the last time. I am going to build a better more permanent paint booth in my garage so that I can get this thing painted.
|
Re: LT1 Burbs 65 Stock SW Build
Very nice build
|
Re: LT1 Burbs 65 Stock SW Build
Quote:
|
Re: LT1 Burbs 65 Stock SW Build
5 Attachment(s)
My bedsides showed up from FredsTruckParts and I sanded them down and worked on them. They were pretty decent and much better then the 4 I have spent over 1500.00 on.
|
Re: LT1 Burbs 65 Stock SW Build
5 Attachment(s)
I then put the bed together and marked out the trim holes and drilled all of them.
|
Re: LT1 Burbs 65 Stock SW Build
4 Attachment(s)
I probably put 8 coats of 2k on these sides and now at 600 with wax degreaser they really shine. I spent hours with paper wrapped around items as small as a pencil trying to get into hard to sand spaces, hopefully it shows when color is on.
|
Re: LT1 Burbs 65 Stock SW Build
5 Attachment(s)
I am in the middle of hood surgery, the sandblasted hood I had stored inside for 2 years was junked and the old hood I had outside for 2 years was used. The sandblasted one was heavily pitted from what I don't know and it had a large in-dent in it, but I needed the inner structure out of it. I ordered a new lower panel so got back to drilling spot welds. I used this time to POR15 the inner structure so I will never have to worry about it, also ground of the original paint on the next known bad spots but found no rust.
|
Re: LT1 Burbs 65 Stock SW Build
1 Attachment(s)
New panel installed.
|
Re: LT1 Burbs 65 Stock SW Build
Looks like it is coming along fine.
Great work as always. I bet you can't wait for the sanding to be done with. |
Re: LT1 Burbs 65 Stock SW Build
Nice work
|
Re: LT1 Burbs 65 Stock SW Build
Good job on the hood panel
|
Re: LT1 Burbs 65 Stock SW Build
Your build sucks, can you tell im jealous cuz mine is still in pieces? great work sir!!!
|
Re: LT1 Burbs 65 Stock SW Build
1 Attachment(s)
Had to swap garages last weekend to do maintenance on the kids cars, I booted the wife's car out.
|
Re: LT1 Burbs 65 Stock SW Build
1 Attachment(s)
Thanks guys, sanding and bodywork sucks. Did get my seat recovered and my front bumper and guards rechromed.
|
Re: LT1 Burbs 65 Stock SW Build
1 Attachment(s)
In between sanding I have been doing other things like rebuilding my evaporator.
|
Re: LT1 Burbs 65 Stock SW Build
Nice progress! Been keeping up with you on Facebook as well.
|
Re: LT1 Burbs 65 Stock SW Build
Great Job. Top quality work bar none.
Will you make it to PIR? |
Re: LT1 Burbs 65 Stock SW Build
1 Attachment(s)
Pm your shipping info, i got a little somethin for ya!!!
|
| All times are GMT -4. The time now is 02:55 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright 1997-2025 67-72chevytrucks.com