Re: What did you do with your truck today, Part 3
 

Thanks. Yup. Sucks cause the weathers perfect out here and I’m itchin to go cruising but still waiting on that Steele gasket to get here.

Re: What did you do with your truck today, Part 3
 

Thanks but I'm in Indiana. Too far.

Re: What did you do with your truck today, Part 3
 

I got nothing done "on" my truck but did get a few things out of the cab that I put there on the move to Idaho.

Got my spray gun lamp up in my new garage on a new shelf I finished tonight. This gun was used to spray the truck in the photo. That photo was taken the day I shot it Aug 1st 1977. It was my third paint job, my parents got me the gun for a high school graduation present! They knew where I was going in life. :D I made the lamp just last a while ago after it hung in my garage for 25 years. I painted the socket for the light bulb Omaha Orange, the color I shot the truck that day. The picture frame is also that color. I made a living with that gun in my shop when I opened it. It's a Craftsmen my mom bought at the Sears in the first mall in the area in Hayward California. I didn't get a "real gun" (Devilbiss JGA502) for a few years a at the shop. And still used it for primer for many years.

Brian

Re: What did you do with your truck today, Part 3
 

A great remembrance to days gone by!

Re: What did you do with your truck today, Part 3
 

maybe. my lights and gauges have been working for 20 years though. whatever the issue I will locate it and destroy it!!

Re: What did you do with your truck today, Part 3
 

That's the spirit! Let us know...

Re: What did you do with your truck today, Part 3
 

Installed the fire extinguisher behind the driver seat. Commercial 5# w metal valve so it can be refilled when it gets below charge.

Re: What did you do with your truck today, Part 3
 

When did you move to Boise? I have not been on the board much since work on the truck slowed down (too may honey dos!). Would like to get together some time.

Re: What did you do with your truck today, Part 3
 

I was checking my lack of light issue and I noticed a gas smell. its a carb but it was raw gas. I looked around and my pressure regulator hose was seeping a tiny amount. tried to tighten the clamp and it seems its faulty. will get that replaced soon. got nowhere with the lights though. fuses are good. I didn't pull the switch yet. i have no headlights, tail lights, or gauges. seems like it could be the switch. i hope i have brake lights. haven't verified that.

Re: What did you do with your truck today, Part 3
 

With everything out and fuses good, it's probably a faulty switch. Try bypassing the switch with a jumper wire from the hot side to your light lead. But you probably already knew that...

Re: What did you do with your truck today, Part 3
 

GREAT idea.. I have a box of Dads old Binks 7's...
Binks & and centari 2000 I sprayed a LOT of square body peelers code 17 and 21 with them.

Re: What did you do with your truck today, Part 3
 

Checked on parts today. My new oil pan should ship this week. My SFI damper with serpentine pulley is still in engineering, no date or cost yet. My custom spindles are done just waiting for shipping when he gets back in town and I can send them to Pete and Jake's to finish the front axle. Guess I will work on my thousands of hours of polishing.

Re: What did you do with your truck today, Part 3
 

Just got a call from BHJ. My SFI damper with serpentine pulley will be done in 5 weeks. $1000, another problem solved. Happy days!

Re: What did you do with your truck today, Part 3
 

Sunday I took what was probably the final cruise of the season...

Re: What did you do with your truck today, Part 3
 

Yup. The salt hit the roads here in southwestern Ohio last night...

Re: What did you do with your truck today, Part 3
 

paying a local race fab rod shop.. a bunch... to me there is a value to have a receipt from reputable shop for that work. AND if i don't do it it will be drive able sooner. he does this for a living and does great work.

new coil rear suspension. wheel opening is 26" 245/60/15 tires
MII tubular A Arms front no coil overs or bags. it will be 1" lower than rear 235/60/15
all new brake lines master cylinder and booster under floor
Power steering
keeping original steering column. it will be cut down and a plastic bushing made for the bottom.wife said NO WAY to loosing original wheel.

I may get it back before thanksgiving.
i am researching and deciding weather or not to relocate gas tank to rear? mustang? or re install one in the cab. i will measure and evaluate. currently had half barrels in bed for fuel tanks.
STOKED to get it back so i can piddle with it!!

Re: What did you do with your truck today, Part 3
 

I think you are spot on. Some things are better left to the professionals. I would rather pay someone to make sure some things are perfect than to try to do it myself even if it hurts the wallet. When I have parts made I try to find someone that not only will make it but is excited about making it. Usually an old guy (like me) in a small shop.

Re: What did you do with your truck today, Part 3
 

I have been here since mid August, yep, we need to get together.

Got my garage painted and some of my art up, WHOOO HOOOO! Building my shed kit last night kicked my butt, I didn't want to stop had had to.

I'll be back to my truck in not too long.

Brian

Re: What did you do with your truck today, Part 3
 

That's nice, my shop is a total disaster. I wanted to build another shop this year but was stuck on a project out of state all summer.

Re: What did you do with your truck today, Part 3
 

Just watched a movie:

Re: What did you do with your truck today, Part 3
 

I need to put the big hole in the little cover. I'm going to try to do this myself. This will be my first attempt to make something important with my mill. I bought the big block cover from Summit for $52. My plan is to cut the big block seal holder out of the cover with my rotary vice and bore a hole to fit in my 292 cover and mind meld them together. It looks like it will just fit. I ordered this boring head. https://www.shars.com/4-adjustable-b...mbo-8-pc-set-1 It was pricey but will give me one more capability with my mill. I was going to send it out but decided to go for it. If I fail all i'm out is a $53 cover and a cover I can't use. If I pull it off I'll feel pretty good about myself.

Re: What did you do with your truck today, Part 3
 

A secondary challenge will be alignment with the crank nose. I assume you'll be tacking it in place while it is mounted on the block. Be careful not to melt the seal! (but hey, you can always punch in another one after the smoke has cleared!)

Re: What did you do with your truck today, Part 3
 

I figure if I set the boring head center off the existing hole on the 292 cover and cut the big block cover with the rotary vice in the big block hole I should retain the same center. Of course I have no idea what i'm doing. Succeed or fail I will be smarter when I'm done.

Re: What did you do with your truck today, Part 3
 

As long as those Asian guys machined everything spot on, the additive error won't get you. :ack: I would at least put the BB cover in place and check concentricity before I cut it.

Re: What did you do with your truck today, Part 3
 

How are you going to locate both centers in the exact same x/y axis without a common fixture for both pcs?

Re: What did you do with your truck today, Part 3
 

I figure I will clamp the 292 cover on the mill and set the boring head to exactly the same as the existing hole and then using the same center enlarge the hole to 3.6" Then using the big block hole on the rotary vice with the self centering vise in the hole I should maintain the center and mill it down to 3.6". This keeps me just outside the collar on the big block cover and just inside the screws on the 292 cover. I should be able to drop the big block collar in the 292 hole and maintain the center. I don't think it has to be within .oo1". some of them are made out of plastic and have some play when you mount them. I realize it has to be close but not space shuttle close.

Re: What did you do with your truck today, Part 3
 

Didn't get much done had to make arrangements for my car hauler to be delivered from GA. It will be here Friday. I put my speedo block off on my trans after polishing of course. I have GPS speedometer. I drilled and tapped in some stainless steel 1/8" pipe plugs in my dipstick hole and the bolt hole.

Re: What did you do with your truck today, Part 3
 

Slick!

Re: What did you do with your truck today, Part 3
 

I started working on my blower belt guard again. I had already sanded the chatter out of the cut outs and blocked it down to 600 grit. Using the sandpaper mandrel on my rotary tool I sanded the cut outs with 1000 grit, 1500 grit and 2000 grit and then polished with tripoli. I will now start sanding the faces further. I like to finish places like the cut outs first so WHEN my rotary tool slips it doesn't bum me out so much.

Re: What did you do with your truck today, Part 3
 

grounded my taillights and installed blue dots:metal:

Re: What did you do with your truck today, Part 3
 

:wop:

Re: What did you do with your truck today, Part 3
 

didn't get to do much besides pulling it out and later back into the garage. been working on my house. trying to get the inside painted before my family comes over for the holidays. its getting chilly. hate the impending doom of winter.

Re: What did you do with your truck today, Part 3
 

Doom of winter, really, New Mexico? We had 6" of snow last week and 7 deg. I guess it's all about perception.

Re: What did you do with your truck today, Part 3
 

here you go , couldn't understand why they wouldn't operate properly , does seem like driver side is a little dimmer than passenger, may have to investigate that more, just glad to find the problem and fix it.

Re: What did you do with your truck today, Part 3
 

I went to the courthouse today and started a Racing company (XXXX XXXXX Racing). In my county it cost $25 to file a DBA. Took that to the bank and opened a bank account. Received a debit card and checks. Sent my credentials to PRI show in Indy to get my pass in. Before this I always had to depend on others to get me passes to closed trade shows. I have a feeling this company may lose money.

Re: What did you do with your truck today, Part 3
 

I've seen some really weird inexplicable electrical problems solved with better grounds.

Re: What did you do with your truck today, Part 3
 

I received my boring head today and started the timing cover. I installed the cover on the engine ran the screws in slowly doing the countersunk ones first to make a repeatable install. After setting the boring head to the existing hole I moved it .005" to center it. I then took cuts of .100 until I got close and did a finish cut of .005. I will reinstall it tomorrow and see how it fits. Then cut the other center out. I have no idea what I'm doing.

Re: What did you do with your truck today, Part 3
 

Most of us wouldn't have known how to spec the boring head for purchase. You're gonna knock this one out of the park. Sounds like you're already .005" more accurate than the factory hole.

Re: What did you do with your truck today, Part 3
 

LOL, Naaaa, you are now a professional race car driver! A guy I work with at my new job has raced his whole life! OMG every time this guy talks it's about a different wild story, Baja 1000, NASCAR, everything but drag racing. He says he doesn't want to work days on a car for a few second thrill. LOL

He is now into Sprint cars, racing is this guys life!

Brian

Re: What did you do with your truck today, Part 3
 

Good to see you guys getting stuff done on your trucks!

Brian