Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
Maybe there's a way to fix it but I found stock fenders with rusted bottoms. Seemed easier to patch them then trying to cut up new fenders. |
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
Maybe the gap won't bother you, it sure would save a lot of work and then you know there's no hidden rust. |
Re: What did you do to your truck today part IV
3 Attachment(s)
got one door frame stripped and reprimered and installed new door check. Found some rust at the bottom of the door that will have to be POR-15'd or blasted, but not too bad....yet. Even came across the original paint(Light Blue).
|
Re: What did you do to your truck today part IV
@rvrfoot How'd the repop door fit?
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
washed it it's been yrs (2014) since I washed it started clay bar ran out of time
|
Re: What did you do to your truck today part IV
2 Attachment(s)
Sanded the firewall to 600 grit. Few more spots and then a good cleaning and masking and ready for paint! :metal:
|
Re: What did you do to your truck today part IV
2 Attachment(s)
I got the engine & trans pulled out, pressure washed the 57 years of dirt and oil off of everything...I also power washed through what was left of the frost plugs. ;-)
Engine on engine stand now! |
Re: What did you do to your truck today part IV
1 Attachment(s)
Got some paint down. Now for cutting and buffing and it should look almost perfect.
|
Re: What did you do to your truck today part IV
1 Attachment(s)
After about 6 hours of sanding, I finally got some stain on the bedwood. A few more rounds of sand-then-stain, and I hope to get some urethane down this weekend.
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
1 Attachment(s)
I installed my roll pan today.Attachment 1680820
|
Re: What did you do to your truck today part IV
2 Attachment(s)
Got the pipes installed, Woke up half the subdivision getting to the shop, but what the heck - they had to wake up anyway! Dan took his time and had to route carefully run around the oil filter and transmission pan, I have torsion bars so he was able to bring the pipe in the center of the arch and go to the rear, good clearance.
|
Re: What did you do to your truck today part IV
3 Attachment(s)
Installed my new auto meter gauges and a clock.Attachment 1680903
Attachment 1680904 Attachment 1680902 |
Re: What did you do to your truck today part IV
1 Attachment(s)
More rust repair. This is very intimidating as it's my first time but I think it's coming out ok. Nothing is welded yet. Gotta fit floor pan next.
|
Re: What did you do to your truck today part IV
1 Attachment(s)
Attachment 1680984
run fuel line from tank |
Re: What did you do to your truck today part IV
Replaced shifter bushings , installed press on door seals, buffed out the paint and installed some Cragar S/S.
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
1 Attachment(s)
Put on my new window and vent window.Attachment 1681049
|
Re: What did you do to your truck today part IV
2 Attachment(s)
|
All times are GMT -4. The time now is 09:05 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com