Re: Attempting my first build 72 K5
Quote:
|
Re: Attempting my first build 72 K5
Quote:
I honestly forget where I seen it. I think it was a online wood veneer supplier for furniture ,cabinets.I will try to find it again. |
Re: Attempting my first build 72 K5
1 Attachment(s)
Quote:
|
Re: Attempting my first build 72 K5
5 Attachment(s)
I have finally figured out the modifications the PO (original owner) did to install the 36 gallon gas tank.
1. He removed the rear cross-member that has the 2 fuel lines going across the top of it. 2. He tack welded threaded nuts to the inside bottom of the frame rail so he could hold the tank with the straps that where on there. 3. He welded a cross bar going from the 2nd to last body mounts to compensate for the loss in reinforcement for removing the original rear cross member that sits in between the frame rails. I cut off the threaded nuts using a sawzaw and dremel. Now I have to figure out a solution for the cross bar that welded to the body mounts. If you're wondering why the 2nd to last body mounts are removed from the frame is because this part was riveted to the body so we had to cut them to get the body off the frame. 1. Do I try cutting it off? 2. Find some replacements and rivet or bolt on new (used) one on? Anybody know where I could find a set? |
Re: Attempting my first build 72 K5
Threaded nuts that where welded to the inside of the frame rails on each side. There was a total of 4
|
Re: Attempting my first build 72 K5
3 Attachment(s)
Pics this time
|
Re: Attempting my first build 72 K5
1 Attachment(s)
Quote:
For the level of build you're doing, I'd vote to put it back like it came...and I think you could with not too much effort. My frame was hacked on and cracked. We had to do a fair amount of prep work on it too. Attached is a pick of the frame I bought my exhaust hanger off of. The whole frame is for sale for $500. I called and asked if he'd sell me the hanger...and he didn't blink. Might be worth a call to see if he'd take off your pieces too. Also, member Uncle had a 72 frame for sale/part out forever. It was very rusty, but that cross member might be workable if he's still got it. Here's the website with the frame for sale (just scroll down when you get there): http://www.billstruckshop.com/67-72used.html |
Re: Attempting my first build 72 K5
I'd replace the missing OEM support with grade 8 bolts and thread loctite and call it a day. I need to look and see what if any work was done to install the Hickey tank in my Blazer.
|
Re: Attempting my first build 72 K5
I did source an original cross member from a pickup that will fit exactly the same. If he could sell me just the hangers that would make everything a lot easier.. I'll give him a call and see what he says.
|
Re: Attempting my first build 72 K5
Looking like progress brother. I'd go with the suggestion of putting it back the way it came from the factory also.
|
Re: Attempting my first build 72 K5
Sockalaminski - Agree 100%..
|
Re: Attempting my first build 72 K5
Quote:
|
Re: Attempting my first build 72 K5
I know you got an update worthy of pics - let's see em! ;)
|
Re: Attempting my first build 72 K5
5 Attachment(s)
It's been a while so I thought I would update with a few more progress pics.
The PO made some modifications to the frame that required some minor work to put this back to its stock form. First was the custom tow hitch that was welded to the outside of both sides of the frameAttachment 1359120 Attachment 1359121 He also made some bad drill holes on the top side of the frame, so I patched that up to make it look decent enough. I'm not even sure if there is supposed to be a hole there or not. Attachment 1359122 Attachment 1359123 The rear cross member was drilled out to compensate for the larger gas tank and he welded a cross bar to the hangers for the body mounts. I cut that off using a sawzall. Then I cut the rest of cross bar as close as I could to the hangers off and then finished it off with an angle grinder and flap disc to smooth it down. Attachment 1359124 |
Re: Attempting my first build 72 K5
2 Attachment(s)
managed to save the hangers and then drilled out the rivets.
|
Re: Attempting my first build 72 K5
2 Attachment(s)
Thanks to Seventy one who came over and helped me tack weld this piece of the front leaf spring where I accidentally cut into when I had to cut out the spacer that wouldn't budge when removing the leaf springs
|
Re: Attempting my first build 72 K5
5 Attachment(s)
I absolutely hated the look of the painted front end of the frame and front axle..So I had them powder coated to match everything else.
|
Re: Attempting my first build 72 K5
3 Attachment(s)
more close up shots
|
Re: Attempting my first build 72 K5
Mike that looks great!!!!
|
Re: Attempting my first build 72 K5
Nice!
|
Re: Attempting my first build 72 K5
Awesome! Powder coat is the best.
Hopefully the areas we worked on look like they were never messed with now that it's coated. |
Re: Attempting my first build 72 K5
Great build! Way back on page one you were asking about the heater core and where you could get a replacement because LMC didn't carry it. The Truck Shop in Orange, California sells new ones. They are $59 if I'm not mistaken.
|
Re: Attempting my first build 72 K5
Thanks guys!
Cameo - I think I'm going to just have mine refurbished. I've been talking to the guys at Classic Auto Air |
Re: Attempting my first build 72 K5
Probably a smart move. I am sure they will make it better than the new Chinese reproduction stuff.
|
Re: Attempting my first build 72 K5
I now have a bad case of frame envy - just beautiful.
|
All times are GMT -4. The time now is 05:14 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com