Re: The Snortin' bull
2 Attachment(s)
Well all running well though my stereo did not like the MSD .And the good used refurb one wire alt I used did not like it either.I installed an MSD cap. and from TUFF STUFF a new 120 amp one wire alternator. All better now.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
2 Attachment(s)
The Snortin' Bull made it out to it's second GOOD-GUYS event. Had a great time. Made a lot of new friend's.
|
Re: The Snortin' bull
2 Attachment(s)
Off with the neck.The fuel tank neck.I had a dummy neck in for the past year. Time has come to smooth thing's out.
|
Re: The Snortin' bull
4 Attachment(s)
Cut out an initial patch piece,20 Gg. Trimmed.Bent a slight compound curve into the patch.Set in after some minor prep.Started to tack in. Dinner is ready gotta come back to this later.
|
Re: The Snortin' bull
2 Attachment(s)
Got some part's for parking brake install.From the Control Cables company.
|
Re: The Snortin' bull
1 Attachment(s)
A new accessory.A back window hat rack.
|
Re: The Snortin' bull
1 Attachment(s)
Static buzz still from MSD .I installed this BOSS noise filter for the radio and no more buzz or static. It work's.
|
Re: The Snortin' bull
1 Attachment(s)
Back earlier in the build I had found a parting out truck and got a rh sun visor.As the Bull originally was lh only.Well the left had one fell apart while driving the other day.So I had to refurb it.Now it matches the right.Sans the original vinyl.
|
Re: The Snortin' bull
1 Attachment(s)
Headliner kept sagging between the mounting points.LMC kit is nice though I had to add extra mounting point's.
|
Re: The Snortin' bull
Do you have any pics of your parking brake install? Was curious if you used the factory rear cables? I went to their website and the prices for their stuff isn't bad.
Bret |
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
2 Attachment(s)
Kept having some water come into the cab after the Seattle rain or washing.None from the windshield it seemed to be thru the cowl and down to the vents.Even in the center from the wiper motor area.I seam sealed anything of question.
|
Re: The Snortin' bull
2 Attachment(s)
The sealed beam headlamp's in the dark in Seattle rain weather are not good.So out they will go.I got a h4 conversion set to install.An updated harness with relay's also.
|
Re: The Snortin' bull
1 Attachment(s)
I had read this on the forum and you do have to open up the hole behind each lamp on the headlamp retaining plate's.
|
Re: The Snortin' bull
2 Attachment(s)
New front lighting harness installed.Scrubbed down everything and painted buckets and retaining plate's,Relays in for high beam and low beam.
|
Re: The Snortin' bull
1 Attachment(s)
All work's just waiting for the dark to align headlamps. Just posin' with the halo ring's.
|
Re: The Snortin' bull
Quote:
Quote:
|
Re: The Snortin' bull
No pressure, but I'm looking forward to the parking brake install also.
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
Quote:
|
Re: The Snortin' bull
1 Attachment(s)
The weather has been real rainy,My garage is full and shop.No new recent work on the Bull .Photo op'
|
Re: The Snortin' bull
2 Attachment(s)
Been driving a lot almost 10k miles in the Bull now.The Seattle rain is non stop thought I would take advantage of it.Wet sanded the white today.Some 2000 and light soapy water.A year of non cleared base coat lookin good and old .
|
Re: The Snortin' bull
3 Attachment(s)
Check straps or door stops. Using the jeep one's to do the mod at Crown jeep parts. Look close at the boxes the factory number is on them. These fit the later trucks pretty easily. Though take a little work to fit to the 60-63.lOOK close the originals are split bracket to rubber stop. Original pins fit also.
|
Re: The Snortin' bull
5 Attachment(s)
The jeep door straps do take some work. Nothing major. the original holes in the door shell need to opened slightly. I used a RH angle drill with a step bit in thru the inside of the door shell.. The pivot bracket on the pillar is best I think to be split ( cut ) in half and than slightly thin down the jeep strap to fit better .
|
Re: The Snortin' bull
1 Attachment(s)
Left door check strap done using Jeep Cherokee parts.
|
Re: The Snortin' bull
1 Attachment(s)
Deluxe wheel. Got a new jem to control the Bull. In good shape. Needs cleaning and some repair and paint.
|
Re: The Snortin' bull
Very Nice!
|
Re: The Snortin' bull
2 Attachment(s)
The deluxe wheel was in fair shape though had about a 9" open wound on the bottom of the hoop.The inner steel hoop was exposed and rusted. Cleaned and prepped and then some PC7 and some curing by the fire some sanding and than some more of the same till like new. Well almost more to come.
|
Re: The Snortin' bull
[QUOTE=Palf70Step;8181317]Very Nice!]
Thank's Palf .These wheels are tough to come by . |
Re: The Snortin' bull
3 Attachment(s)
Deluxe wheel 5 hours later. Out with the old in with the new. Refurbished and installed. Feeling like a Cadillac king in a GMC.What's better than that ?
|
Re: The Snortin' bull
:metal: Very N I C E :metal:
|
Re: The Snortin' bull
1 Attachment(s)
The Snortin' Bull and I didn't fall off the earth. Just been out driving and driving. Still got a list of things to finish. Just been having fun. Picture out back at work .
|
Re: The Snortin' bull
That is what we are supposed to do with them, DRIVE!
|
Re: The Snortin' bull
Quote:
|
All times are GMT -4. The time now is 05:48 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com