Re: Project '64 Cheapskate
Kool beans about the car. I've always loved that model of Camaro. Second gens have a soft spot for me.
|
Re: Project '64 Cheapskate
The engine and trans are now installed, so I've got a lot of things I can do. When I decided to go with a 700r4, that presented a few issues, namely the driveshafts. The cost of having a driveshaft made or modifying an existing one can be spendy, and because I was trying to use parts that I already had, I had to break out the tape measure and find ones that would work. Between me and all of my friends, we have about 50 spare driveshafts and 90% of them are 1-piece. Unfortunately, all of the 1-piece shafts we had were either too long or too short. After a bit of careful measuring, I determined that the front driveshaft from the '79 Suburban would work. The Suburban was a 454/th400, and the 700r4 is slightly shorter by about 1.5", so I ordered a transmission yoke with an 1.5" longer total length just to be sure that I had good spline engagement. My '64 was a C-20, which has the superior "bell-style" heavy-duty carrier bearing, so I ordered a new one and it pressed right on to the Suburban shaft. Once I tried to put it all in, I realized that there was no way to install it due to the length of the shaft, the size of the carrier bearing, and the distance I had between the tailshaft of the transmission and the trailing arm crossmember. I tried every combination, and nothing worked.
So, I fired up the cutoff wheel and took out a 2" section of the crossmember, just enough to where I could get the slip spline section of the driveshaft through. I already have the shaft in place and resting on the carrier bearing mount in this picture. http://i222.photobucket.com/albums/d...ps573c188c.jpg I didn't want to leave a 2" gap in the crossmember because it's a part that carries a lot of load and I didn't want to create issues later with it cracking, so I built a reinforcement plate. Notice that I saved the cut-out piece... http://i222.photobucket.com/albums/d...ps7e7ed3e7.jpg I popped the cut section back in place and drilled a hole in the center http://i222.photobucket.com/albums/d...ps6d6aeb19.jpg I bolted everything back in place with Grade 8 fine-thread bolts and NyLocks. The fasteners on the ends are actually 2.75" sections of Grade 8 All-Thread. I had to do this for a few reasons. First, all bolts over 1.75" long have a thick section of the shank that's unthreaded, and I needed threads all the way through. Second, the long attach bolts of the carrier bearing bracket were also used as a method to hang the exhaust, but i didn't like that the carrrier bearing would have rubber somewhere in the mounting assembly. The stud eliminated that by having a double nut up on top, secured by a nut underneath, with the remaining stud exposed. Now, the exhaust could hang from the stud and not be a main part of the carrier bearing attach fasteners. You can see that the carrier bearing attach bolts to the bracket are loose. I am waiting until I get the rear shaft in and aligned before I snug those down. http://i222.photobucket.com/albums/d...psc2e71223.jpg http://i222.photobucket.com/albums/d...ps31309947.jpg http://i222.photobucket.com/albums/d...ps1ca13d7d.jpg I also bolted up the headers and attached the collectors, so the exhaust is essentially finished. Next step, final fit of the inner fenders. core support, and radiator. I have a bad feeling that I am going to have to do a bunch of surgery on the shroud to make it work. With the frame "Z", and the serpentine belt set-up, it's going to require some creative thinking. It HAS to look factory when it's all done! I have a buddy who thinks that he's Mr Chevy, and I want to disguise all of the frame mods. When I told him I was lowering the front 5", the first thing he said was "It's too low, the lower control arms will hit on everything". That's true, but after the 2" Z, I have a ton of ground clearance. I want him to look underneath mine and scratch his head and try to figure out how I got mine so low and still have ground clearance. So, this is why I have spent so much time on the inner fenders and everything else that bolts to them. That's one of the reasons why all of the frame and everything that bolts to it is painted chassis black, so it'll disguise all of the surgery. I want to fool a lot of people. There's a bunch of work on this truck that I have taken great pains to hide or disguise. I like doing that kind of stuff. |
Re: Project '64 Cheapskate
Install looks clean! Comin' up on the test-fire!
|
Re: Project '64 Cheapskate
Nice work! It looks like you are getting close...
...unless there is wiring, plumbing or anything else like that to be done. Then it might look "almost done" for a while! I finally got my 62 GMC home. Other than a mediocre paint job it is so nice I might not do anything to it but clean it up and drive it. Posted via Mobile Device |
Re: Project '64 Cheapskate
Attention to detail is fantastic. Awsome build .
Posted via Mobile Device |
Re: Project '64 Cheapskate
Looks kool to me.
|
Re: Project '64 Cheapskate
Great work man! Can't wait to see it finished:metal:
Posted via Mobile Device |
Re: Project '64 Cheapskate
I'm sure you'll think of something.
|
Re: Project '64 Cheapskate
Quote:
|
Re: Project '64 Cheapskate
Quote:
Actually, that's the way I wanted to do it, because I felt that it would have served two purposes. I could get the 2" up and move the frame 1" forward at the same time. In the end, we went with cutting straight and triple-walling the frame because it was absolutely imperative that the core support mounts and motor mount locations reamain in the stock locations, and at the time, it seemed to be the easier way. It gets a little weird around the steering box, and you have to be careful how you address that area, especially if you have one of the power steering adapter plates. In the end, everything lined up perfectly, and we even lowered the engine mount stands 2" so we wouldn't have to rework the cab floor and not have any valve cover clearance issues at the brake booster and the heater box. And it'll still look stock when you open the hood, especially after I sectioned the bottoms of the inner fenders and reattached the stock rolled lips. |
Re: Project '64 Cheapskate
Man I love this build! All the little details are perfect! I love the inner fender bottoms that are reshaped! I'd seen the vac gauge mod before when searching and somehow didn't catch that it was in a build thread. I like how you redid the brake pedal and seat placement, I don't like where any of that stuff was from the factory. The little details inside the A/C box are awesome, and making all the cables and controls work like you did takes a good bit of time and thought to get right.
I'd take this truck over the typical shiny custom any day just because of all the little details that are "right". So many of the "bling builds" are only surface deep and the little stuff is forgotten... I think part of the reason those type builds aren't driven is that they're not enjoyable when they are driven, because they were just thrown together from "cool" parts! You will have a true driver that is a blast to drive because everything has been designed to work in harmony. Awesome work, and I can't wait to see more! |
Re: Project '64 Cheapskate
John-
I am so glad that you finally visited my thread. I've posted on your threads in the past that I absolutely dig the work you do, so your compliment means a lot to me. I hold you in high regard because you always think outside the box and your attention to detail is impeccable. Quote:
I had big plans to make my '55 a super-sanitary, detailed to the hilt show stopper. After a bunch of thought, I've had a change of heart because I know that I could never fully enjoy the truck if I did that. I have a feeling that the '55 will probably get sold before I ever finish it. |
Re: Project '64 Cheapskate
Well, tomorrow is a big milestone birthday for me, so the wife threw a surprise party for me last night, with a big help from Kustombrad. We had a great dinner, had a bunch of friends show up from all over, and I got some great gifts.
http://i222.photobucket.com/albums/d...psc6bab61c.jpg With the help from Brad, Lynn's gift to me was the complete set of parts I needed to rebuilt the steering on the '64. All new Moog stuff, which I was eyeing anyway. I wondered if the other people around us thought I was weird when I started hooting and hollering as I was pulling out steering parts in a nice Italian restaurant. Brad's gift was a set of MSD wires, which I really needed. I had almost bought that same set a few weeks ago, but I decided to hold off. Good thing, huh! A very good friend, Tom Clark, showed up and I was surprised to see him. He lives a good distance away, and I would have never expected him. He's one of Brad's pinstriper buddies, and he made me a special sign to signify my birthday http://i222.photobucket.com/albums/d...ps77c2627a.jpg Check out the wrapping paper he put it in. He said that he spent a couple of minutes with a Sharpie to make it look cool. http://i222.photobucket.com/albums/d...psc60c966a.jpg I decided to take a break on the truck this weekend and hang out with the wife, but very soon you will start seeing a lot of pictures on this thread. I have been doing a lot of work, but I'm holding off until I can finish each little project before I post up anything. A big thanks to Lynn and Brad for making my birthday a memorable one, and for all of my friends for sharing it with us!! |
Re: Project '64 Cheapskate
Happy B-day and welcome to 50 plus club.
|
Re: Project '64 Cheapskate
Happy Birthday! Looks like you got some good stuff for the truck. We put new Moog steering/suspension parts on mine too. Love the pinstriping as well, & look forward to seeing your progress pics! :bowtie:
|
Re: Project '64 Cheapskate
Happy birthday! Those are the gifts you will remember years from now when you are driving that truck down the road.
Posted via Mobile Device |
Re: Project '64 Cheapskate
Happy Birthday! Great Presents, hope they get put to good use soon! Glad it was a good day for you.
Posted via Mobile Device |
Re: Project '64 Cheapskate
Happy BDay dude!
Posted via Mobile Device |
Re: Project '64 Cheapskate
Quote:
Sounds like you had an awesome birthday, with I got truck parts like that! |
Re: Project '64 Cheapskate
Happy Birthday, man! The truck's coming along nicely. I'll bet you're itchin' to get that stuff installed. :wave::two:
|
Re: Project '64 Cheapskate
Happy 50th !!
I just rolled the half century mark this month as well (on the 9th) !! Nice score on the front end parts ! |
Re: Project '64 Cheapskate
Happy birthday to you bunch of kids.
Posted via Mobile Device |
Re: Project '64 Cheapskate
nice work and happy-b-day kat!
|
Re: Project '64 Cheapskate
Happy Birthday!! I honked and waved as I drove through (yeah, sure) with my wife on our way to So Lake Tahoe to celebrate our 15th anniversary.
|
Re: Project '64 Cheapskate
Happy B-Day!!!
|
Re: Project '64 Cheapskate
Happy Birthday Dude.
|
Re: Project '64 Cheapskate
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Happy 15th Anniversary!! 15 years, huh? You're way ahead of the average, my friend. Good Job! The wife and I are going to celebrate the Big 2-5 coming up soon. Quote:
Quote:
|
Re: Project '64 Cheapskate
Must've been a long birthday.......where you at? Lol.
|
Re: Project '64 Cheapskate
I went on vacation and took a trip back to Louisville for 5 days to visit my family, and I've been at the California Hot Rod Reunion in Bakersfield for the last few days. It was a great vacation, and with my stressful work schedule, I really needed it. I'll be a little bummed out to go back to work tomorrow and get thrown back into the fire, but I'll get over it.
In the meantime, there has been progress on the '64. I've been doing body work on the inner fenders, so all I have to show for it is a lot of body filler dust. The A/C condenser has been fitted and drilled up, all of the A/C lines on the forward side of the core support are cut and crimped. and now it's ready to blow back apart and get painted chassis black so I can hide all of the hard work I did. |
Re: Project '64 Cheapskate
Bangshift said the Cacklefest was epic! Was Brad there pushin'? Glad you got some time off.
|
Re: Project '64 Cheapskate
Quote:
The Cacklefest was awesome! Brad was using the '49 to push the Tocco, Harper, and Garten Fuel Altered again this year. We went to the tent to go get our wristbands for the Cacklefest, and the lady running the booth asked Brad if he could possibly push TWO cars! Of course, he said yes. So, that meant that we were the first car to light off, kicking off the event. As soon as Roger lit off the Altered, we hauled butt down to the end of the track to get the second car, the Schrank Brother's 1961 record holding B/Fuel dragster. It set the E.T and Mph records in 1961 with an 8.65 @ 183 mph, with a blown 276 cubic inch DeSoto(!) Hemi on nitro. That record stood for two years. That was one bad hot rod in it's day, and when that little sucker lit off, I was blown away at how nasty it sounded. The event was great. The weather was perfect, and it was a great time seeing old friends and making new ones at the same time. Dude, you have got to come here one day and go with us. It's a blast! |
Re: Project '64 Cheapskate
Sounds like a great time. It's on the bucket list. Batting lead off and pushing 2 cars, that's awesome!
|
Re: Project '64 Cheapskate
Any updates on the truck dude?
|
Re: Project '64 Cheapskate
I was working on my son's truck for a good part of the weekend, but I was able to etch-prime the core support and battery tray and did some body filler work on the inner fenders, which are now nearly complete. I would like to get those parts in primer this weekend, and if that goes well, get them wet-sanded and ready for chassis black.
This week, every night after work, I plan on doing some prep work on the condenser, receiver/dryer brackets, and the A/C lines and get them ready for primer. The fan shroud still needs to be wet-sanded with 400 grit and prepped for primer. As soon as the inner fenders and core support are back on, it'll open up a bunch of work that can be done. |
Re: Project '64 Cheapskate
Glad you're still on it. You and Brad have to Convoy to the Reunion next year!
|
Re: Project '64 Cheapskate
Kool just checking on ya.
|
Re: Project '64 Cheapskate
Quote:
|
Re: Project '64 Cheapskate
lil happy b-day kat!
|
Re: Project '64 Cheapskate
Man, that sounds fun. I'll have to get to work!
|
Re: Project '64 Cheapskate
It's been awhile, but that does not mean that I haven't been bustin' on the '64. As a matter of fact, I have been doing a lot of work, but it just wasn't exciting enough to post up pictures. Most of what I was doing was bodywork on the inner fenders and prepping the under-hood parts for paint. Man, I have a real respect for the guys who do bodywork for a living.
If you remember, I took out a 2" lower section of the inner fenders to compensate for the 2" Z we did on the chassis. It was important to me to have it all look factory, so that meant that I had to do some welding and bodywork. Here's a shot of the driver's inner fender right before we primed it. http://i222.photobucket.com/albums/d...ps3bfc6862.jpg And the passenger side: http://i222.photobucket.com/albums/d...psde1a33ca.jpg So after a bunch of sanding and prep work, the parts were ready for paint. Brad offered to do the spraying, and another buddy, Ryan, offered up the use of his shop. A big thanks to Brad and Ryan for doing this! http://i222.photobucket.com/albums/d...ps3bb82e5c.jpg http://i222.photobucket.com/albums/d...ps88034b13.jpg http://i222.photobucket.com/albums/d...ps38854ec1.jpg http://i222.photobucket.com/albums/d...psa9c16b91.jpg The funny part of this is that the paint we used was a Frankenstein mix of a couple of black enamels and it turned out perfect. I'm a stickler for chassis black, and it has to be the right sheen to look "right", and this batch has the perfect eggshell sheen I was looking for. And to top it all off, instead of using the high-dollar Iwata spray gun, we used a $15.99 Harbor Freight special and it worked incredibly well. The next step is to assemble all of the stuff on the core support and start installing parts! More pics to come... |
All times are GMT -4. The time now is 02:33 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com