![]() |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Getting closer to finish line:
|
Re: What did you do to your truck today.The 3rd chapter
3 Attachment(s)
Installed the new axle bearing and seals . All the bearings are American made the grease seals were made in Mexico still better than China . I Also did the carrier bearings so much easier when you put the carrier in the -25 chest freezer for two days and heat the bearings up to 250 . Just slides together that’s frost on the ring gear .
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Got primer on my inner fenders last weekend and yesterday took the time to put some paint on the under hood sides.
|
Re: What did you do to your truck today.The 3rd chapter
Went to put the carrier in and after inspecting the right side shims they look like they were beat in with a punch and sledge hammer left was a thick solid spacer and it was cracked . I had noticed that the backlash was very excessive when I took it apart . I'm thinking it had slop the carrier bearings and someone beat a few shims to the right side tightning the bearings but causing the excessive backlash and put strain on the left bearing which finally failed.
So I bought a shim pack today and going to assemble tomorrow. Did the pinion bearings today ,the old ones looked good but better safe than sorry . |
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
Calling it good 12 thousands for used gears is in the ballpark . When I took it apart it must have been 40 to 50 thousands lots of backlash
|
Re: What did you do to your truck today.The 3rd chapter
1972 C20 took apart the drivers side rear Brake Wheel Cylinder to clean up and a new Master cylinder came in today so will be installing it Soon.
|
Re: What did you do to your truck today.The 3rd chapter
I sprayed WD40 on my crusty rear bumper brackets. ( All I had) Let that soak in. They've been there 50 years. Hopefully I can crack them and not have to break out the torch.
Shiny new bumper is on it's way. :) Thanks GMC Paul. Paul. That's a nice name. I knew a guy named Paul. Oh wait a minute. That was me. Nevermind :crazy: |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Thanks to global warming and early HOT weather getting at or new the 100s already (which I am sure none of us are helping with out old trucks) I adjusted my idle for AC and shut off the heater water via my heater valve.
I think it was a smart move to put in that valve... |
Re: What did you do to your truck today.The 3rd chapter
Got it on a lift in my new garage. Still working to get all my crap up on shelves to free up the floor space.
https://i.imgur.com/WYvKS3Wh.jpg |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
3 Attachment(s)
Painted my front and rear bumpers white..
|
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
Installed lift kit a couple weeks ago, my friend that painted the truck painted my new wheels and I installed new tires.
|
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
I washed, then buffed out the original paint on the front of my truck today. Then I took it for a short drive.
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
A while back I put new cab mounts on Otis, never understood why someone would go to all the trouble to pull the cab, paint it then re-install it on the old broken-down cab mounts? Maybe it's just me, anyway after the install I took it over to a fellow to completely re-align the doors, fenders and hood which he did a slam dunk job. Very thorough.
He also installed the missing rear inner fender bolts (one each side) that connects to the forward cab area. After I picked up the truck, I had this definite pronounced clunk right underneath my clutch foot heel whenever the frame would flex from turning, pothole, approach etc. that was not there before. It was about to drive me crazy trying to pinpoint it, I finally noticed that the sheet metal formed for the horn that the inner fender bolts to was just folded/mated together with no apparent welding spot or otherwise, so I drove a shim in it, and the clunk was no longer there. Bingo! Now I could slightly hear one on the passenger side but not as pronounced. Got underneath and wire brushed down to bare metal, c-clamped it back together and welded the outer lip of what appeared to be about two 12 ga lips together both sides of the truck...whisper quiet now popping is all gone. I borrowed this pic from another thread to show you the area I'm referring to. |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Took the 68 out put 50 miles on it . Ran great handles well only problem I ran into was the starter. Starts great cold won’t turn over hot nothing nada zip . Not even a click . Turned on the headlights had my friend hit the start and the lights go way dim battery tests good . Let it cool and starts right up. Ordered a new one be here Friday
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
I keep moving backwards. I really want to restore my truck to it's original 'medium blue poly' someday, and I decided it would be easier to get the firewall before I put the new engine back in... so now she's got a medium blue poly firewall.
|
Re: What did you do to your truck today.The 3rd chapter
5 Attachment(s)
After procrastinating for the last 3 years and having no carpet in my truck as figured the minute the carpet was installed the 50 year core would start leaking and considering the fact of a new engine going in and redone rad the heater core would be the weak link in the cooling chain. So today started the Heater Core removal process. You have to take out the inner fender to get access to 2 of the 4 bolts that hold the core housing in place. The inner fender removal would be much easier if the truck was on a hoist. Tomorrow the core is coming out.
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
5 yrs since I bought the truck.
Mystery battery died No date code I could see on it. |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
4 Attachment(s)
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Installed rear shock relocation brackets, new adjustable pan hard bar. New 5" springs and removing the rivets now to install a C-Notch. Love my air hammer!
|
All times are GMT -4. The time now is 01:41 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com