![]() |
Re: PO has me PO'd
Plan B, note to self, do not remove shielding
I have to move XIM box up 2 1/2" to clear cables from the XFI controller https://farm5.staticflickr.com/4623/...9f896090_c.jpg[url=https://flic.kr/p/22v8c2U]20180118_120443 https://farm5.staticflickr.com/4718/...b197832f_c.jpg[url=https://flic.kr/p/23yTVSN]20180119_161857 My screw ups, are starting to get expen$ive |
Re: PO has me PO'd
Jim
see your steady at it i have a question going back a few of your posts did you purchase or bend your own brake lines im looking at Inline Tube has kits im going with the stainless Jess |
Re: PO has me PO'd
Quote:
Stainless can be a PITA to flare, but I read where annealing helps Maybe, you could ask first what size nuts come with the part frame and rearend are looking good on your project |
Re: PO has me PO'd
thanks , Jim
|
Re: PO has me PO'd
Thought I'd throw this little tidbit out there.
When sawing with my bandsaw, I heard a thump, thump, thought I broke some teeth, looked at the blade, and there was a build up of aluminum in the kerf. Talking to the manufactor, he had asked what lube I was using, I said none. Told me that was the problem, so now I spray the blade and problem is gone https://farm5.staticflickr.com/4619/...103fb095_c.jpg[url=https://flic.kr/p/Jt7CQ2]20180112_123109 smells like grapes |
Re: PO has me PO'd
Quote:
Glad you're getting quality time with your truck |
Re: PO has me PO'd
These are the two new harness, that I had to replace, they are for the LS series engines, but I have 350ci SBC
The original harness was set up for a crank trigger, so no go. Speaking to Jim at TPIS he's advised me that the new harness's will be an easier hook up. just repin for the firing order, and a step up voltage resistor. Also repin crank and cam sensors The first harness shows the connecters that go to the crank and cam sensors https://farm5.staticflickr.com/4697/...d9b4840b_c.jpg[url=https://flic.kr/p/22kxwKe]20180122_180308 https://farm5.staticflickr.com/4718/...b197832f_c.jpg[url=https://flic.kr/p/23yTVSN]20180119_161857 |
Re: PO has me PO'd
https://farm5.staticflickr.com/4723/...83f12514_c.jpg[url=https://flic.kr/p/23MiLuu]20180127_090603
Rubber isolation blocks from McMaster-Carr, 1" 1/4-20 bottom blocks 10/32x3/4" |
Re: PO has me PO'd
https://farm5.staticflickr.com/4706/...d79a2929_c.jpg[url=https://flic.kr/p/23UxGyo]20180131_100335
I wanted to mount the isolation blocks towards the edges of the aluminum mount, but they were to short. So, I settled for one block in the middle, countersunk and full thread, using my handi-dandi counter sink tool, that has been laying in my toolbox for thirty years, cool, the way you can adjust it for depth https://farm5.staticflickr.com/4722/...2ee75b89_c.jpg[url=https://flic.kr/p/K1Hq8n]20180131_163532 While I was sitting there, admiring my success of the week, poofff, my florescent light above my engine bay blows out. Now, we've all dropped one and know the out come. Carefully, undoing the bulb, it slips momentarily, and clanks the motor, no explosion, great! Bring the whole unit down to change out the other bulb. Put it in, and rehang unit, that is now working, it slips out of my hand, and the whole unit crashes into my motor. I'm stunned, as there is no explosion with shards of glass all over my engine compartment as well as some obnoxious gas we are not to breathe. I packed up and ended my day as I was sure I've extended my luck Now, I can move on to the XIM box, and mount it with isolaters I got from Mcmaster-Carr |
Re: PO has me PO'd
https://farm1.staticflickr.com/806/2...107225e3_c.jpg[url=https://flic.kr/p/Hbyd2b]20180319_104535
tired of tripping on tools and supplies while working https://farm1.staticflickr.com/822/2...8a6eccdf_c.jpg[url=https://flic.kr/p/Hbyd21]20180319_104544 |
Re: PO has me PO'd
changed my mind again, and decided to stack my computers, I think this could be the last change, as I have to get on with the wiring
Mcmasters-Carr sent some U channel to be used to mount the top computer https://farm5.staticflickr.com/4785/...1f21426d_c.jpg[url=https://flic.kr/p/HjFqnS]20180324_16022 |
Re: PO has me PO'd
looking good.
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
upside down, backwards,inverted, and inside out....redundant
If you design something, make sure it is easy to work on....had to add two access holes to allow use of allen wrench for tightening of mounting bolts on XFI XIM mounts on top of C channel https://farm1.staticflickr.com/869/3...0218fda6_c.jpg[url=https://flic.kr/p/238CZBu]20180406_114555 |
Re: PO has me PO'd
https://farm1.staticflickr.com/810/4...fda280d0_c.jpg[url=https://flic.kr/p/25XstPS]20180410_091556
https://farm1.staticflickr.com/800/3...f245a7c3_c.jpg[url=https://flic.kr/p/23goonw]20180410_092439 I had read somewhere that soap will stop aluminum from cloging up disk, don't know if it is working, but my work shop smells like Irish Spring |
Re: PO has me PO'd
What color green is that?
Is that a factory color or aftermarket? Scott |
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
My perferred method of drilling holes....center punch, or transfer punch, center drill, lubrication, and then drill size.
https://farm1.staticflickr.com/867/4...3374a3d8_c.jpg[url=https://flic.kr/p/264kyZ9]20180413_094748 |
Re: PO has me PO'd
I had seen that color before just not with the metal flake.
I will look it up. I like it. I had picked a dark jade green metallic but I like that color a little more. Scott Quote:
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
I found it in an old sampling color chart. In the color chart the flake does not show up as much as in the floor board pics of this thread's blazer.
It looked somewhat aftermarket not factory. Just caught my eye. Did not mean to get the topic off track. LOL Scott |
Re: PO has me PO'd
here's another pic, maybe easier to see...there is a gold flake in there
Off Topic LOL....my whole build thread is filled w/off topic. just random thoughts of what I do every day https://farm1.staticflickr.com/891/2...b58e172b_c.jpg[url=https://flic.kr/p/J4bYLQ]20180415_112104 |
Re: PO has me PO'd
Jim have you given any more thought to parting with a manifold that will work with the Sniper EFI system im contemplating......
|
Re: PO has me PO'd
Quote:
|
Re: PO has me PO'd
Quote:
|
All times are GMT -4. The time now is 05:05 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com