Re: Project Reno - 72 cheyenne rebuild
Quote:
Well ask and ye shall receive. The bumpers look nice. They aren't as brilliant and have a bit of tint from the clear, but I like it. Pictures don't do it justice because it's glossy, but it does have the brushed metal look. http://images2.snapfish.com/23232323...33925%3Aot1lsi I got all the holes taped up so I could spray the back of both bumpers with corroseal and convert the rust. http://images2.snapfish.com/23232323...84334%3Bnu0mrj All the areas that are dark or purple are rust that has been converted. http://images2.snapfish.com/23232323...%3B25%3Aot1lsi Once corroseal was dry I applied a heavy coat of corothane prime to seal out the weather. I love this stuff. It's like liquid caramel. Now all I have to do is spray the bed liner on the rear bumper's step and install. http://images2.snapfish.com/23232323...%3C25%3Aot1lsi While waiting for the corothane to dry I decided to try something and apply a little peel and seal to my door panels. They felt really flimsy. Well, it worked great. The doors sound completely dead when closed. http://images2.snapfish.com/23232323...25234%3Bnu0mrj Next bumpers get installed and I will get the master cylinder on and brakes bled. |
Re: Project Reno - 72 cheyenne rebuild
Those bumpers turned out nice.
|
Re: Project Reno - 72 cheyenne rebuild
Quote:
|
Re: Project Reno - 72 cheyenne rebuild
Your making great progress.
I really like the dash and steering wheel.Looks great. Interior is really going to be sharp. The brushed parts are really cool too. |
Re: Project Reno - 72 cheyenne rebuild
Thanks for obliging! Bumpers do look like they turned out well, but I can't ever get enough :) Want to see them mounted on the truck!
|
Re: Project Reno - 72 cheyenne rebuild
Today I had a small break in the weather and just enough heat to get the bed liner on the rear bumper.
http://images2.snapfish.com/23232323...3A425%3Aot1lsi I covered just the diamond plate and bottom step where hitch ball screws in. http://images2.snapfish.com/23232323...3A525%3Aot1lsi I was also able to prep and spray the shifters cover. http://images2.snapfish.com/23232323...3A625%3Aot1lsi I unmasked after about an hour and it all turned out pretty good. Gonna let it dry overnight and see the results then install the rear bumper. The only bummer was the corothane worked it's way thru the masking in a few visible areas and stuck to the powder coat. I am going to have to try and get it off with a razor blade. That is testament to how sticky corothane is. |
Re: Project Reno - 72 cheyenne rebuild
Had a little time on Friday so installed the rear bumper. It was like a jigsaw puzzle, but eventually got it figured out. It is going to be a pretty stout bumper.
http://images2.snapfish.com/23232323...%3C25%3Aot1lsi http://images2.snapfish.com/23232323...%3B25%3Aot1lsi I think it turned out pretty good and glad that is done. I need to finish putting together the front end before installing the front bumper. http://images2.snapfish.com/23232323...%3A25%3Aot1lsi http://images2.snapfish.com/23232323...3A925%3Aot1lsi Now the weather has changed so progress will slow, but I know this is that last winter it will be unfinished. Can't wait to drive her. |
Re: Project Reno - 72 cheyenne rebuild
Looks nice and solid, part of me wants to install a roll pan and do away with the bumper. Then I think that bumper might just save me if I get tapped from behind. That thing is much more substantial than the factory shiny bumpers.
|
Re: Project Reno - 72 cheyenne rebuild
Wow! That bumper really turned out well. Home stretch buddy! So are you saving the pictures where you step back and get the whole truck for a big reveal? Just close-ups for the last 4 pages :lol:
|
Re: Project Reno - 72 cheyenne rebuild
Quote:
Quote:
Yeah, I spent a lot of time on this bumper because it's older and made well. Much better than today's bumpers. I am saving large view pics of the truck until she is under her own power. My garage is on a steep incline and it would be a task to roll it out and get it back in the garage. Won't be long though and she'll be rolling out on her own. |
Re: Project Reno - 72 cheyenne rebuild
(((((COLD))))) Progress
Today it was biter cold and windy, but took care of a lot of odds and ends. I got the rear support brackets and splash guards for the bed installed. http://images2.snapfish.com/23232323...%3C25%3Aot1lsi http://images2.snapfish.com/23232323...48625%3Aot1lsi I got the drivers door glass installed with all components and front fender back on. http://images2.snapfish.com/23232323...%3B34%3Bnu0mrj http://images2.snapfish.com/23232323...3C534%3Bnu0mrj Bed completely bolted down and got the rear speaker brackets fitted and primed. http://images2.snapfish.com/23232323...3C334%3Bnu0mrj http://images2.snapfish.com/23232323...3C734%3Bnu0mrj I bench bled to master cylinder and a letting the rest of the systems gravity bleed. |
Re: Project Reno - 72 cheyenne rebuild
Pre-turkey progress.
Well, I got my speaker panels painted up body color and got everything mounted into place. I used a little peel and stick on the backside to deaden the panels. They are after all sheet metal. http://images2.snapfish.com/23232323...%3B25%3Aot1lsi Here they are mounted http://images2.snapfish.com/23232323...B3325%3Aot1lsi Now that that is out of the way, I got some help installing the cowl and hood. Cowl went in with no issues, but hood is wacked. http://images2.snapfish.com/23232323...B3925%3Aot1lsi http://images2.snapfish.com/23232323...B3725%3Aot1lsi The ass end of the hood is too high. I have used the loosen and push up on the hood method, but not quite there yet. I elongated the holes on the hinges slightly to aid in adjustability. Hopefully another hour or so and they will fit well. I also started wiring under the hood. http://images2.snapfish.com/23232323...B3625%3Aot1lsi For the most part wiring the engine to harness was easy. I only needed to run the large red wire from bulkhead to starter to power the fuse panel, large purple wire to starter to activate the starter and my sending unit wires to the temp/oil pressure switches. I also hooked up the brake safety switch. Tac is dealt with inside cab from ECM. I still need to wire the front lights. http://images2.snapfish.com/23232323...B3525%3Aot1lsi Very happy I have no more body panels to install. Just a few more tweaks and should be good. |
Re: Project Reno - 72 cheyenne rebuild
Your corner speaker mounts turned out great. One day, I'll be wrapping up loose ends like you - I'm envious! But, I'm making progress that I'm happy with on mine as well... just about a years worth of progress behind you :)
|
Re: Project Reno - 72 cheyenne rebuild
JL Audio too! The mounts turned out nice! that said i was wondering if they may need a little deadening material stuck to the back side for vibration?
Curious, did you lube up the hinges real well before you installed them? I think they should settle down a bit if you lube them up and cycle the hood up and down a bit. |
Re: Project Reno - 72 cheyenne rebuild
Quote:
Quote:
As for the hinges, I did not lube, but they do move freely. I will give that a try though. I'll try anything at this point. I'm gonna keep trying stuff till they settle in. They are original hinges and used with this original hood so I know they will eventually work. Happy Turkey Day! |
Re: Project Reno - 72 cheyenne rebuild
Well, after a lot of lubing of the hinges and adjusting/re-adjusting I got them very close. However, there is too much tension on the front of hood when closed and looks like the hinges are starting to bend. There is a fair amount of play in the rivers so went ahead and ordered a set from GMC Paul's with new springs. Hopefully this will do it. In the mean time, started wiring the front headlights. Should make some more headway tomorrow.
|
Re: Project Reno - 72 cheyenne rebuild
mo progress. Well, yesterday i made some good headway on the front light harness.
http://images2.snapfish.com/23232323...65734%3Bnu0mrj I didn't know how to route the wires so based on the assembly guide got everything loomed and attached to the core support. http://images2.snapfish.com/23232323...65834%3Bnu0mrj I strayed from the install instruction slightly when extending wires to the passengers side. I spliced in and soldered the wires rather than doubling them in the connectors. I think it will be more stable and endure the test of time. I temporarily attached the front bumper to give me rough length for my wires. http://images2.snapfish.com/23232323...65934%3Bnu0mrj http://images2.snapfish.com/23232323...%3A34%3Bnu0mrj Today i should have the truck wiring totally complete. "Oh what a feeling" |
Re: Project Reno - 72 cheyenne rebuild
Very nice progress on the truck! Your getting close now.
|
Re: Project Reno - 72 cheyenne rebuild
Quote:
|
Re: Project Reno - 72 cheyenne rebuild
1 fuse at a time set up a quick disconnect at the battery so you can kill the power quick.
|
Re: Project Reno - 72 cheyenne rebuild
Quote:
|
Re: Project Reno - 72 cheyenne rebuild
Nice progress! I like DWilbur's advice too!
|
Re: Project Reno - 72 cheyenne rebuild
Wiring has been a major road block on mine. Trying to figure out all the interior crap I can get rid of is killing me :) You're wiring job looks awesome!
|
Re: Project Reno - 72 cheyenne rebuild
Quote:
|
Re: Project Reno - 72 cheyenne rebuild
Quote:
that bumper looks very sweet. goes well with the paint color. |
All times are GMT -4. The time now is 07:02 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com