![]() |
Re: 1968
Quote:
|
Re: 1968
4 Attachment(s)
Today i presure washed the front cross member and rear end. Monday i an going to wire wheel both parts and then I will sand blast them.. As you can see it is very cold here in Florida. It was in the mid 70"s.
|
Re: 1968
Quote:
Posted via Mobile Device |
Re: 1968
Quote:
Nice progress. You are making better use of the mother-in-law room since theres no one occupying it. Whats the numbers for on your shirt? Lookin' Good keep it up. |
Re: 1968
Freezing here too.
You are leading the charmed life there in fla. Posted via Mobile Device |
Re: 1968
Quote:
|
Re: 1968
Quote:
|
Re: 1968
3 Attachment(s)
I don't remember who gave me the idea of removing the broken bolt in the pinion shaft. But thanks it worked and now I am in business again. I was a little skeptical at first. But I mean to tell you it worked and thanks again.
I did not have a seal pick so I used this small pick which looks like a small ice pick. again thanks. |
Re: 1968
3 Attachment(s)
Toay, I got a lot done. First, I wire wheeled the rear end. Tried to sand blast but the thing would not work right. So I primed the thing and painted it black.
|
Re: 1968
3 Attachment(s)
Next, I removed the rear end from the 1967 frame. The more I looked at the yellow springs the more I disliked them. So I painted them gloss black also today.
|
Re: 1968
3 Attachment(s)
I pulled the backing plates from the 1972 rear end ad cleaned them up. I also painted them with heat resisting rust-oleum black.
|
Re: 1968
2 Attachment(s)
Next, I used a die grinder and made a x on the ribbits on the rear cross member on the 67 frame. I removed the cross member and installed the one I took off the 1972 frame. Now I can install my brake lines and it will have a good support and the rounting is going to look great. I like the way the 72 brake line are rounted. Thanks BOMP for that idea.
|
Re: 1968
Looking good, nice progress
Posted via Mobile Device |
Re: 1968
Quote:
I don't even dare to miss a day of not tuning in. If there's a catagory Im nominating you for the fastest build award.:haha: |
Re: 1968
Quote:
|
Re: 1968
Quote:
|
Re: 1968
Quote:
|
Re: 1968
5 Attachment(s)
Today, I got a couple thing finished. One, the rear end off the 1972 frame was mounted on the 1967 frame. Second, I mounted the backing plates back on the 1972 rear end after I blasted and painted them. Third, I wire wheeled the front cross member and sand blasted it and primed and painted the cross member. I am going to start and dismantle the front end tomorrow. I am going to take my time and finish it this week I hope.
|
Re: 1968
The 1967/1968 frame is getting real dusty setting out under the canophy I think I will buy the sides for the canophy that way I can get ready for paint after the holidays.
|
Re: 1968
I also will order the outside seals and outer and inter bearings on the rear end and the front yoke seal. The yoke seal is not leaking but I have to change the yoke anyway. It is a little larger and my u clamps are to short. I have the yoke and I might as well change it.
|
Re: 1968
The speed at which you are making progress is awesome and an inspiration to me and others im sure.
|
Re: 1968
Good work, moving along nicely
|
Re: 1968
Quote:
|
Re: 1968
Quote:
|
Re: 1968
Today, I installed the front cross member and the upper a frames. There is a slight difference between th 67 and 72 frame bolt pattern. About 1/32 of a inch for the bolts that screw thru the frame to the welded bnuts on the cross member. But it in in now. I also got the upper and lower ball joints off without a hitch. I am going to call tomorrow and see If I can return them for 72 ball joints if not it is not the end world. That brings a note. I fixed my sand blaster and now it works like it suppose to. I changed the tip to use fine sand. Some fix right. I have a few items that need sand blasted. But tomorrow is another day.
|
All times are GMT -4. The time now is 05:41 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com