Re: 67c10 build
 

The lower jamb piece I thought turned out great. I had a few hours fitting it but welded it up and hit it with some 36 grit pads and it cleaned up nice

Re: 67c10 build
 

Hung the door and fender before welding the rocker in cab corner. I'm happy with fit and finish of it all.

Re: 67c10 build
 

Much better then it was with all gm metal

Re: 67c10 build
 

Did you have any problem with the ECE Panhard Bar clearing the Billet Diff cover?...

Re: 67c10 build
 

WOW Those Headers are AWESOME!!!!

Re: 67c10 build
 

The rear pan hard bar was straight so I had a friend bend it for me to clear the diff cover. Thanks for the compliment there Sanderson bb8s

Re: 67c10 build
 

Really nice job with the rust repairs on the cab, wish my cab corners looked that good.

Re: 67c10 build
 

Thanks Keith. Pictures are a little deceiving, the back of the cab corners are a little bumpy but I think should smooth out fine

Re: 67c10 build
 

What a *****IN update!!! Props on keeping the filler neck where it oughtta be :metal: Nice work on the metal! What welder do you have? Pulley setup is sick too!

Re: 67c10 build
 

I bought a reproduction fender, don't remember the manufacture, and just kept fighting it to make it fit. I got so frustrated I cut up the fender and fixed my original. I'm officially a firm believer there is no replacement for oe metal

Re: 67c10 build
 

The rear of the fender was so beat up I replaced it also

Re: 67c10 build
 

Thanks sir. I've always been a fan of the in cab tank. I can understand the efi guys moving them but this big block is gonna be drinking right out of the cab. I've been using a miller 140. It's been great, my first time welding with gas and all I can say is wow

Re: 67c10 build
 

No ebfabman but those sand disk sure clean up the welds nice

Re: 67c10 build
 

Can you get me a pic of how you bent that panhard on the truck?... I am looking at doing that...
That Chassis just looks awesome... Great work going on the cab... I also did a complete new bed... That sure has save me alot of time... Dan

Re: 67c10 build
 

Driver side was about the same as far as work but only partial inner rocker and this side needed a little bit of the floor pan

Re: 67c10 build
 

I lucked out, all the cab supports were good so I just hit them with some rust converter and primed them

Re: 67c10 build
 

Had to split the rocker on this side to get it to align with the door

Re: 67c10 build
 

Someone's been busy, build looks awesome keep up the
good work!

Re: 67c10 build
 

very nice updates, looking good

Re: 67c10 build
 

Thanks Cameron, how's yours coming along? Hope to attend my first meet next year with my truck. Hector I ended up going with your tires size, looks much better now in my opinion. Can't wait to see those rally's on your truck.

Re: 67c10 build
 

Haven't made much progress but I hope to bend up all of my brake lines starting next week.

Re: 67c10 build
 

Rust is evil. Found a little more when trying to fill a pin hole. Took a 2" wholesale and made a series of holes till I found no more rust

Re: 67c10 build
 

Not sure why it posted sideways, hope this ones better. Got it welded up and it finished nicely

Re: 67c10 build
 

Hope this pic turns out or I don't know what to do. Finished up both fenders, not sure it was worth the time but there both original and fit great

Re: 67c10 build
 

nice metal work... keep it up!