![]() |
Re: LFD's 4dr Tahoe Build
your boy is getting big, i remember when my kids played in my trucks now they are all driving them:lol: it goes by fast so enjoy it, and oh nice work on the truck:lol:
|
Re: LFD's 4dr Tahoe Build
Is this the one you had in a baby seat in Lo-Buck?
|
Re: LFD's 4dr Tahoe Build
Quote:
Kevin LFD Inc. |
Re: LFD's 4dr Tahoe Build
Quote:
|
Re: LFD's 4dr Tahoe Build
So once my Wife came home I had some time to go out and play abit. I got the rear end of my "6 link" bars finished up and was able to mock up one side to make sure it lined up with the stock C4 Mono leaf link, and it does:metal:
I also got the rear mount for the Diff made and installed but I still have a bit of welding to do once I pull it back out. Then it is off to get a run over the surface plate to make sure I won't get any leaks down the road. You can see the spacer I Tig'd to the out side of the diff mount and I have done this to all link mounts for added strength as well as to take up the extra 3/8" of length in the shoulder bolts I have. Kevin LFD Inc. [IMG]http://i16.photobucket.com/albums/b20/rokcrln/Link5.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b20/rokcrln/Link6.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b20/rokcrln/Link7.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b20/rokcrln/Link8.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b20/rokcrln/Link9.jpg[/IMG] |
Re: LFD's 4dr Tahoe Build
Great build, I'm subscribed. I'm putting a C4 IRS in my truck soon. Did you do anything to the aluminum parts on your irs to clean them up? In the pictures they look bright and clean. Do you plan to leave them as is or paint them with your new diff cover? How about the the ABS sensors do you have any plans to do away with them or just leave them.
|
Re: LFD's 4dr Tahoe Build
Quote:
Kevin LFD Inc. |
Re: LFD's 4dr Tahoe Build
I played a bit tonight with my rear link set up and made good progress. I finished the end of the first link and for not being a very good Tig welder I say it turned out well. Once I get my RE8's I can build the bag mounts and start on the shock mounts as well. I need to order a few Hiem joints for the track locater on the hubs but the last pic shows the direction I am going with it.
Kevin LFD Inc. [IMG]http://i16.photobucket.com/albums/b2...rln/Link10.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link11.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link12.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link13.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link14.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link15.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link16.jpg[/IMG] |
Re: LFD's 4dr Tahoe Build
Wow, it really takes a smart dedicated brain to accomplish that. NICE!!!
|
Re: LFD's 4dr Tahoe Build
Those turned out great! Are you going to put bushings or another mechanism on the end-links (between components) in case the suspension ever unloads?
|
Re: LFD's 4dr Tahoe Build
Quote:
Now for the fun part I get to spend most of tonight with the Plasma making all my parts and pieces for the other side so it all matches and still add 1 or 2 gussets to this rear mount. I hope to have my Re8's soon so I can start mocking up placement and ratios and see what is left for the shock placement. Kevin LFD Inc. |
Re: LFD's 4dr Tahoe Build
Can you share what sizes you are using for the Hiem joints for the track locater? Are they 5/8x5/8" and is the tubing 1" ID? I'm about to order the supplies for my IRS and I wondered what you went with.
|
Re: LFD's 4dr Tahoe Build
Quote:
I have not ordered mine yet. I will be calling in the morning to see what will work best for my set up. If you are doing this in a truck I would use the stock rear diff cover and just raise the frame 4" and use the stock set up for the track. I only went through this in order to keep the rear floor as low as I could for the rear seat my wife wanted. Kevin LFD Inc. |
Re: LFD's 4dr Tahoe Build
Kevin,
Do you need a slam bag rs8 for mock up I have three in my garage and one is damaged to use for mock up welding purposes! Tony from Norcal |
Re: LFD's 4dr Tahoe Build
Quote:
You did mean to say RE8 right? Thanks Kevin LFD Inc. |
Re: LFD's 4dr Tahoe Build
Hey Kevin this suburban is so ambitious. The rear hatch with hidden hinges is great. I was wondering if you are going to do something slick with the tail lights. I always thought there was too much metal around the lenses. Maybe a larger tailight that appears stock would fill the void. Just thinking outloud. Anyway great job with all your work. I will keep tabs on your progress.
|
Re: LFD's 4dr Tahoe Build
I am still holding you to the CHEVROLET lettering across the back :)!
|
Re: LFD's 4dr Tahoe Build
Quote:
Quote:
Kevin LFD Inc. |
Re: LFD's 4dr Tahoe Build
Quote:
Thought you said you had one upstairs you were going to use? Everything looks great BTW. |
Re: LFD's 4dr Tahoe Build
Quote:
|
Re: LFD's 4dr Tahoe Build
1 Attachment(s)
Quote:
|
Re: LFD's 4dr Tahoe Build
Or, check with NWD02...he's putting in a panel with the older chevrolet script so he might be willing to hook you up with the original letters. I have a gate that the letters are pretty good on but the bottom's rotten that I could cut out the letters for you...but shipping would probably kill the deal for you.
|
Re: LFD's 4dr Tahoe Build
2 Attachment(s)
Quote:
Quote:
Quote:
Kevin LFD Inc. |
Re: LFD's 4dr Tahoe Build
Whos truck are the backwards stuff going into..?
|
Re: LFD's 4dr Tahoe Build
Gate is on the Blazer I sold to Hickman and the dash is back in my attic;)
Kevin LFD Inc. |
Re: LFD's 4dr Tahoe Build
Well I think for sure today was the hardest day of this build so far, but I got it. I was working on the front 4 link bars for the C4 and had a heck of a time in trying to keep the bars low and still maintain the smallest amount of front to back wheel travel during the full range of up and down wheel travel. I started out with equal length bars and had them parallel to the frame and that gave me over 1 1/2" of front to back wheel travel through the 10" of travel. After allot of different set ups and allot of thinking I ended up with 30" top bars and 31 1/4" lower bars. They are parallel to the ground at ride height and during the full 10" of travel my front to back movement is less then 3/8" total. I have it set up for the wheel to be centered in the wheel well at full dump and at ride height it is back 5/16".
Here are a few shots with the laser set up for checking the final configuration. First shot is full stuff and the laser is dead center of the hub Axel nut. Next is ride height and a close up of the tape. Then the last hub shot is at full lift and it is once again perfectly centered. I still need to play with my track bars abit because I am getting a few degrees of tow change during full travel and I think I can get it all out with some more work. If I can get it to zero it will also decrees the 5/16" number a very small amount. Kevin LFD Inc. [IMG]http://i16.photobucket.com/albums/b2...rln/Link27.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link28.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link29.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link30.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link26.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link25.jpg[/IMG] |
Re: LFD's 4dr Tahoe Build
So in order to make it all work I had to bring the top bars into the floor by 2". This really won't be a problem because my seat mounts are just above this and will still allow for a sheet metal cover over the seat mounts and top bars and the seat will still lay forward and down flat like it should. I will make some simple covers to go over the bars but leave access for the bolt to be removed. The upper bar has to have a down ward bend to it in order to clear the rear floor step structure and also to keep the bar below the magic 2" floor #. I will bend this bar in my hydro bender but first I will sleeve the inside of the 1 1/4" tube with a .120 wall 1" on the inside then if I feel it is needed I will add a gusset blade to the bottom of the tube.
The lower links are parallel to the ground at ride height and are angled in to the frame about 3"+- at the leading end of the bars to minimize the front to back travel of the hub during the up and down travel. I have 10" of travel 5" each way from ride height and that should have the frame 1" off the ground with a 31" tall tire and 6" of frame clearance at ride height. Kevin LFD Inc. [IMG]http://i16.photobucket.com/albums/b2...rln/Link21.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link17.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link22.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link18.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link20.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link23.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link24.jpg[/IMG] |
Re: LFD's 4dr Tahoe Build
nice work, its lookin real good
|
Re: LFD's 4dr Tahoe Build
1 Attachment(s)
Check this out. I'm putting it on my tail gate. Something a little different... MEKDAD machined it for me. :metal:
|
Re: LFD's 4dr Tahoe Build
Looking good LFD :metal:
|
Re: LFD's 4dr Tahoe Build
Looks good Kevin.
|
Re: LFD's 4dr Tahoe Build
Quote:
Kevin LFD Inc. |
Re: LFD's 4dr Tahoe Build
I know not much but it was my evenings work all the same. I finished welding the bars and added a small brace to the two bent arms. Here is a pic of the section I cut out for the poly end to weld to so you can see what is on the inside. The sleeve runs from the ploy end to 4" back from the rod end. Combined it is just over .250 thick and I will add 4 plug welds on each side of the bend to lock it all into one piece. I am waiting on 3 new threaded ends that I should have on Tuesday so I can finish up these bars and start on the toe in/out bars on the diff cover.
Kevin LFD Inc. [IMG]http://i16.photobucket.com/albums/b2...rln/Link31.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link36.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link35.jpg[/IMG] [IMG]http://i16.photobucket.com/albums/b2...rln/Link34.jpg[/IMG] |
Re: LFD's 4dr Tahoe Build
Wow Kevin, that IRS is sure taking you lots of hard work, evrybody can weld but not evryone can design. Im pretty sure your 5.3 conversion will be easier
cant wait for that! :cool: |
Re: LFD's 4dr Tahoe Build
It sure has been allot more work then I was thinking but it is still worth every bit as I see it coming together. If I would have just been ok with cutting up higher in my floor this would have been allot faster and easier but I want a certain look when it is done so I brought it on my self. I too believe the 5.3 swap will be a cake walk especially with PorterBuilt's C4 Drop Member that is on it's way. I still have a few trick up my sleeve that will add extra work but it will all be worth it in the end. Thanks for checking in somtimes I think I am just posting this for my self:lol:
Kevin LFD Inc. |
Re: LFD's 4dr Tahoe Build
Quote:
|
Re: LFD's 4dr Tahoe Build
Quote:
|
Re: LFD's 4dr Tahoe Build
Quote:
|
Re: LFD's 4dr Tahoe Build
Quote:
I'm always lurking and taking notes :lol: |
Re: LFD's 4dr Tahoe Build
Quote:
Quote:
Quote:
Quote:
Thanks for the feed back guys. I would have the front 4 link done tonight and installed but the Brown truck seems to have forgotten were I live and my threaded ends are not showing up. I need to get the 4 bars installed so I can start figuring out just were my toe in/out bars need to be set for proper tracking. Kevin LFD Inc. |
All times are GMT -4. The time now is 07:32 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com