Re: What did you do to your truck today.The 3rd chapter
Nice paint job
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
Could be I was going by the GM part number below the grommet in the photo. It may still work. I just recognized that one from to many years workin on those engines. |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Took the roll pin out of the shift lever. It should be a press fit, but it's a slip fit now, and slides down over time and use. Going up to the hardware store to buy a new one. If that doesn't work I'll just put in a bolt with a smooth shank.
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Ended up buying a Dorman Pcv grommet has the right measurements and looks like the one I took off . Says it’s for a 68 250 ci
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
3 Attachment(s)
Got my finished small block loaded into my Suburban for transport to the installers place.
|
Re: What did you do to your truck today.The 3rd chapter
Motor looks great
|
Re: What did you do to your truck today.The 3rd chapter
Agreed, the engine looks great, I couldn't help but notice the 'Princess Auto' box there then realized you're in Canada too. :)
I don't think I've seen a 12 point bolt on the crank before. |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Finally got the floor finished and added new wheel wells. Next step when I recover is prep for paint. This is my daily driver so I did the bed while on the truck
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
5 Attachment(s)
Todays fun . Fixed the brackets and put it back together . Waiting on the new alternator this one the bearing is going and I don’t have the time to rebuild it and it’s a 37 amp model to boot. Never seen this before a red piece of plastic in the oil dipstick . Thought it was orange paint and I boggered it up a little with the wire wheel .
|
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
Screen shot from a video of it running shame we can’t upload directly from a phone or computer on this forum . The plastic filter is temporary have a metal one coming. The upper bracket I clamped onto a heavy piece of metal to help avoid any warpage it worked
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Installed the fuel tank in this frame-off. It was the "hardest" thing I had left to do.
For tips perhaps, I installed Classic Heartbeats grommet. Slid it on the filler neck with dish soap. Installed the tank loosely, with my son's help. Tried dish soap to get the grommet through, failed, probably not the soap. My son kept a blow drier on it while I started it from the inside, finished from the outside, not bad at all. All with a ball-end tool, I swear by them for installing grommets. NOS fuel cap or was until today. 71 is a rare cap, but I found one on the cheap long ago. |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Great reading guys, love all the pics n tricks and all ...........
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Cleaned up the bed for the next car show this Saturday.
|
Re: What did you do to your truck today.The 3rd chapter
Wow Ned, great looking wood, well done.... good luck at the show!
|
Re: What did you do to your truck today.The 3rd chapter
5 Attachment(s)
Ned that quarter sawn looks beautiful.
Found why temp gage wasn’t working on the 68 stepper as I retapped the harness . Wasn’t the sender wire was brittle and had green corrosion where it exited the harness . New wire and spliced where it was still good in the harness used solder and heat shrink . I retapped the entire harness mainly looking for other bad wires found none . Took out the leaky heater core and found a huge mouse/chipmunk nest |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Finished up the install of the S10 washer bottle and pump. Don’t think the squirters ever worked that good.
|
All times are GMT -4. The time now is 05:56 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com