![]() |
Re: My 63 Project
1 Attachment(s)
Door thresholds in.
What is the best way to secure the door rubber trim in?? Glue?? Double sided tape??? |
Re: My 63 Project
1 Attachment(s)
Little bit o bling!!!
|
Re: My 63 Project
1 Attachment(s)
Custom drive shaft made and installed.
|
Re: My 63 Project
1 Attachment(s)
Quote:
|
Re: My 63 Project
1 Attachment(s)
E-Stopp installed. I tested it and it works very nice!!!
|
Re: My 63 Project
And here is the E-Stopp in Action.... Once it applies the parking brake, you can not move the truck!!!
https://www.youtube.com/watch?v=BoOGGFS51gA |
Re: My 63 Project
1 Attachment(s)
Nothing new in this picture, I just liked the look with the light inside. Thought it was cool.
|
Re: My 63 Project
1 Attachment(s)
Windshield installed.
|
Re: My 63 Project
1 Attachment(s)
Back window.... Not so much so.
The gasket is too big for this original back window. So my glass guy is going to cut me a new, just a bit smaller, back window. |
Re: My 63 Project
1 Attachment(s)
Got some pictures of the shroud.
|
Re: My 63 Project
Today is the day!!! We cranked the motor without gas to make sure we had oil pressure and to make sure the motor would turn over. Added some gas. And here is the results. This is the video of the very first attempt to start this motor.
|
Re: My 63 Project
Ok.. so let's try again to upload the first start video....
https://www.youtube.com/watch?v=V9oDF6myngE |
Re: My 63 Project
1 Attachment(s)
I decided that the carb needed a rebuild since the motor would not rev quickly. And since this carb had been sitting for like the past five years or so. Here is my first go at a carb rebuild.
|
Re: My 63 Project
1 Attachment(s)
And the after. She fired right back. And idled down nicely. Have to some more tuning but she runs a ton better. And now the motor will rev!!
|
Re: My 63 Project
Bad ass build so far, nice attention to detail!
|
Re: My 63 Project
Great Build! Just read the whole thing! How much clearance do you have on the bottom side of the driveshaft with the flipped crossmember?
|
Re: My 63 Project
1 Attachment(s)
Quote:
Looks to be about an inch and a half. |
Re: My 63 Project
Cool, thanks for the picture, I am planning a 4" drop on my truck, I think I will try this trick!
|
Re: My 63 Project
Quote:
|
Re: My 63 Project
So we got ambitious today and pulled her out for a run up and down the street....
https://www.youtube.com/watch?v=FA4O...ature=youtu.be |
Re: My 63 Project
1 Attachment(s)
That edlebrock had some issues with jetting and such. And it really wasn't the right carb for this motor.
So.... Holley (quick fuel) 780 CFM!!!! |
Re: My 63 Project
1 Attachment(s)
Let her spend a couple of nights outside.
|
Re: My 63 Project
1 Attachment(s)
Got the bed sides back on her. The drivers side isn't bad. The passenger side is probably beyond repair.
|
Re: My 63 Project
3 Attachment(s)
So I took her out for her first car show this weekend... The Las Vegas Super Run.... We had a good time and LOTS of people stopping by to ask questions...
|
Re: My 63 Project
1 Attachment(s)
Along with my good friend Tony who brought out his original 65 Mustang that he purchased new for $3400 in 1965.
|
All times are GMT -4. The time now is 02:50 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com