The 1947 - Present Chevrolet & GMC Truck Message Board Network
Page 13 of 27 « First 389101112 13 141516171823 Last »
Show 40 post(s) from this thread on one page

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   Tools, Shops and Shop Safety (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=89)
-   -   Lets Play Whatz It? !! (https://67-72chevytrucks.com/vboard/showthread.php?t=481596)

dwcsr 10-05-2011 04:25 PM
Re: Lets Play Whatz It? !!
 
Quote:
Originally Posted by stellar (Post 4936672)
here is another one, but I don't know what it is. (RULE VIOLATION) this one is free if you pay the boating fees.
This is part of a distributor machine. Its an attachment but I forgot what exactly its for. Might be for magnetos

stellar 10-05-2011 04:28 PM
Re: Lets Play Whatz It? !!
 
Quote:
Originally Posted by dwcsr (Post 4936726)
This one is already on page 2 king pin alignment tool
Well no wonder you knew what it was. Do ya want to buy another one so you can do both sides at once? Sorry for the Fup

What is the other one? I have been asking for years and can't find out. It is made by Allen electric. They made electrical test equipment. I hope one of the computer wiz kids can find it somewhere. I can't.

stellar 10-05-2011 04:33 PM
Re: Lets Play Whatz It? !!
 
Quote:
Originally Posted by dwcsr (Post 4936749)
This is part of a distributor machine. Its an attachment but I forgot what exactly its for. Might be for magnetos
Magneto was my guess too. I contacted a mag repair shop years ago and sent pics and they didn't know either, but said it may be for that.

You are too good to play any more. just show the whatz it stuff. I will dig around and look for something else.

dwcsr 10-05-2011 05:47 PM
Re: Lets Play Whatz It? !!
 
Quote:
Originally Posted by stellar (Post 4936755)
Magneto was my guess too. I contacted a mag repair shop years ago and sent pics and they didn't know either, but said it may be for that.

You are too good to play any more. just show the whatz it stuff. I will dig around and look for something else.
These guys will know what it is
http://www.distributortester.com/index.asp

RUSHNBOBO 10-05-2011 08:40 PM
Re: Lets Play Whatz It? !!
 
somebody put up a pic ...I'm getting bored

dwcsr 10-05-2011 10:55 PM
Re: Lets Play Whatz It? !!
 
1 Attachment(s)
Automotive, Very rare, used in the 30's to late 50's

gmtec93c1500 10-06-2011 04:33 PM
Re: Lets Play Whatz It? !!
 
my first thought was to push calipers back ... but they never had hydraulic brakes in the 30's.... some sort of seal installer? im thinking theres another piece to this tool something to catch the little legs on the sides

dwcsr 10-06-2011 06:58 PM
Re: Lets Play Whatz It? !!
 
Quote:
Originally Posted by gmtec93c1500 (Post 4938880)
my first thought was to push calipers back ... but they never had hydraulic brakes in the 30's.... some sort of seal installer? im thinking theres another piece to this tool something to catch the little legs on the sides
Nothing to do with brakes, not a seal installer. There are suppose to be 2 more bars or handles about 6 inches long like on the top that screw into the holes in the second section. It only is used for GM cars and light trucks 3/4 ton and down. The top section is threaded internally and screws onto the part that this tool services.

gmtec93c1500 10-06-2011 07:54 PM
Re: Lets Play Whatz It? !!
 
king pin presss?

RUSHNBOBO 10-06-2011 08:04 PM
Re: Lets Play Whatz It? !!
 
Rear Spring Shackle Bushing Remover and Replacer ?

motornut 10-06-2011 10:06 PM
Re: Lets Play Whatz It? !!
 
ball joint tool ?
my socket for the 4X4 balls it "screws" the ring in kinda looks about the size of the center bit

71swb4x4 10-06-2011 10:40 PM
Re: Lets Play Whatz It? !!
 
Here you go guys, get-r-dun!! http://67-72chevytrucks.com/vboard/s...d.php?t=487664

dwcsr 10-07-2011 12:08 AM
Re: Lets Play Whatz It? !!
 
Its not for springs or suspension or steering. Its a tool that you would say why the hell did they make a tool for that? It is a Kent Moore made tool.

gmtec93c1500 10-07-2011 12:25 PM
Re: Lets Play Whatz It? !!
 
wheel stud installer?

RUSHNBOBO 10-07-2011 12:39 PM
Re: Lets Play Whatz It? !!
 
yoke installer, trans or diff ?

RUSHNBOBO 10-07-2011 12:40 PM
Re: Lets Play Whatz It? !!
 
steering wheel installer ?

dwcsr 10-07-2011 02:20 PM
Re: Lets Play Whatz It? !!
 
Its not an installer of anything, its not for steering or any part of steering or wheels or suspension., Not for the rear end or a yoke. Its used to remove only one item on the car or truck and each vehicle only has one of these parts. It is driveline related.

Its overly complicated for what it does and your going to say what the hell did they make that for? I have never had a time I actually needed it in about 50-60 times I have done this procedure and more times than not the part almost falls out even if its still good. Its also not used to install that same part.

If no one gets it I'll post a picture of a tool that is used after it.. Hopefully that will be enough input for you to guess.

dwcsr 10-07-2011 02:34 PM
Re: Lets Play Whatz It? !!
 
I'm going to add it is a GM Kent Moore J tool that starts with 0 that's how old this dog is.
so its j-0XXX

RUSHNBOBO 10-07-2011 03:19 PM
Re: Lets Play Whatz It? !!
 
1 Attachment(s)
Clutch Gear Bearing Puller ?

dwcsr 10-07-2011 03:26 PM
Re: Lets Play Whatz It? !!
 
Quote:
Originally Posted by RUSHNBOBO (Post 4940629)
Clutch Gear Bearing Puller ?
Yes, It takes more time to install that clunker than it would take to just pull the input shaft out by hand.

RUSHNBOBO 10-07-2011 03:40 PM
Re: Lets Play Whatz It? !!
 
Quote:
Originally Posted by dwcsr (Post 4940646)
Yes, It takes more time to install that clunker than it would take to just pull the input shaft out by hand.
Damn !!! that was a tough one; at least 2 hours searching......I actually got this part number..... "J 937" .....the "0" threw me off for a while; could be a slightly different flavor. ;)

dwcsr 10-07-2011 03:50 PM
Re: Lets Play Whatz It? !!
 
Quote:
Originally Posted by RUSHNBOBO (Post 4940672)
Damn !!! that was a tough one; at least 2 hours searching......I actually got this part number..... "J 937" .....the "0" through me off for a while; could be a slightly different flavor. ;)
Depending on who lists it, its either a J-0937 or J-937, I suspect that its J-937 because its companion tools have J-933 and J-932 on the tool itself.

RUSHNBOBO 10-07-2011 04:57 PM
Re: Lets Play Whatz It? !!
 
dwsr.......I don't know if you have or own this tool but this guy is looking for one, and many other vintage Kent Moore tools

http://vintageautostuff.com/chevrole...t-moore-j.html

dwcsr 10-07-2011 08:09 PM
Re: Lets Play Whatz It? !!
 
Quote:
Originally Posted by RUSHNBOBO (Post 4940819)
dwsr.......I don't know if you have or own this tool but this guy is looking for one, and many other vintage Kent Moore tools

http://vintageautostuff.com/chevrole...t-moore-j.html
I have the 937, 936, 933 and 932.

RUSHNBOBO 10-07-2011 08:21 PM
Re: Lets Play Whatz It? !!
 
Quote:
Originally Posted by dwcsr (Post 4941119)
I have the 937, 936, 933 and 932.
sent pm

Rush


All times are GMT -4. The time now is 01:30 PM.
Page 13 of 27 « First 389101112 13 141516171823 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com