Re: My 52 GMC Build
 

there arent check valves in the ports of the hydro boost master cylinder outlets, and air rises, so pressing the brake under accumuator pressure forces the air back and forth until it bubbles out the reservior.

I didnt believe it either, I started with a slap empty system when I changed the rear axle in my 65 with a tahoe hydroboost setup, cracked the ports, dripped, tightened, started engine, stepped on the pedal a few times and had 4 wheel brakes clapping at me. the pedal kicked a few times at first, but after that was smooth as silk. YRMV, but I bet they dont.

Re: My 52 GMC Build
 

Thanks for the info guys. Joedoh I think your right the peddle was better tonight. I now have a low one push peddle and can hear the brakes move. I bleed the brakes again got a few little bubbles. I will have to wait till I start the motor. I have never dealt with hydro boost before. Then my friend Joe stopped in and confirmed that how my brakes are now is how it should be with a hydro boost without the motor running. So thanks everyone I feel much better tonight. It was driving me nutz. On to the next on the list.

Re: My 52 GMC Build
 

awesome!

Re: My 52 GMC Build
 

Thumb lights eh. :)

Re: My 52 GMC Build
 

lol... yea but I agree with Kees... they look more like Minions!!! must have been the inspiration to Pixar.... :lol:

Re: My 52 GMC Build
 

So tonight I got a few little things done so I could put the passenger inner fender on loose. Replaced turbo oil return hose with one good for oil and installed block heater power cable. So I rotated the turbo housing so I can run the new piping along the inner fender. Yup that looks much better than the black flex hoses.
Attachment 1477838

Re: My 52 GMC Build
 

Nice! Where you get your piping and couplers, siliconeintakes.com?

I love that site. They have everything at good prices.

Re: My 52 GMC Build
 

that looks nice

Re: My 52 GMC Build
 

That looks nice! The worst part to me of a HX35 or HX40 is the stupid PITA ginormous snap ring that retains the compressor housing on the center section. :lol:

Re: My 52 GMC Build
 

Thanks allpurposepipes.com they sell all sizes of intake and exhaust pipe
Thanks
Thanks. To rotate the housing the ginormous snap ring is nice (squeeze with pliers and rotate)

Re: My 52 GMC Build
 

But if the snap ring pops out, it is not so fun. :lol:

Re: My 52 GMC Build
 

Thanks very much to CRGRS 66 for hooking me up with some custom power steering lines. They turned out great.
Attachment 1479367

Attachment 1479368

Re: My 52 GMC Build
 

So for today I started putting the doors together. I got the door latches modified for the door poppers. I'm using bike brake cable and adjusters so I can get the right pull and have the solenoid out of the way of the window.
Attachment 1479369

Re: My 52 GMC Build
 

Oh and Saturday night we where out for dinner. My friend Joe text me and said he left something in my shop for me. This is what I found. :metal:
Attachment 1479395

Attachment 1479396
The license plates for the truck are LOWER50S I have had them for almost 9 years.
We had talked about doing this instead of tint. It's perforated vinyl we settled on a design but I had no idea he went and did this. Thanks Joe

Re: My 52 GMC Build
 

All looks good Lower50's!
Great idea on the rearwindow!

Re: My 52 GMC Build
 

Really nice! Where did you get them? They are way nicer than any I've cobbled together from NAPA.

Re: My 52 GMC Build
 

Regional hose. CRGRS 66 works there.

Re: My 52 GMC Build
 

That looks cool! Good to have buddies look'in out for ya!

Re: My 52 GMC Build
 

nice stuff, whats the deal with your latch there? interesting to see how that is set up.

Re: My 52 GMC Build
 

Not so funny thing happened to me today, jumped on my bike to go for a spin down the mountain and surprise....no brakes! Some a-hole stole my brake cables. Lower 50s, you haven't seen any used cables have you? Window treatment looks good, when my buddies stop by all they do is leave me with empty beer cans! LOL
Rob

Re: My 52 GMC Build
 

Thanks Rob and no I went and bought new cables on my way to work. LOL

Re: My 52 GMC Build
 

Got the door poppers all built. The solenoids are mounted to the lower access panel of the door for easy service and no holes in the door. Short vid below pic.
Attachment 1479745

http://vid51.photobucket.com/albums/...ps7cvkthy9.mp4

Re: My 52 GMC Build
 

I also installed the rubber outer window scraper and my door drip wings.
Attachment 1479775

Re: My 52 GMC Build
 

Good stuff. I like the modern aspect of the poppers but not keen on shaved handles. Are you shaving them or just adding poppers?

Re: My 52 GMC Build
 

They are shaved
Attachment 1479888

Re: My 52 GMC Build
 

Re: My 52 GMC Build
 

Today was a great day!! I got the door windows installed and door poppers in. It all went together as smooth as frog snot.
The last 2 pics show the popper installation with the cables.
Then a vid of the poppers in action.
Attachment 1480081

Attachment 1480082

Attachment 1480083

Attachment 1480084

http://vid51.photobucket.com/albums/...psald1k0tm.mp4

Re: My 52 GMC Build
 

Truck is looking good . Nice work on the door poppers. Do you have a manual back up for them?

Re: My 52 GMC Build
 

65sub Yes I will have a few options to get in.

Re: My 52 GMC Build
 

Nice work on the door poppers. Very cool set up.

Re: My 52 GMC Build
 

Thanks AD
Well I have been working on the electrical panel plate. It's now ready to get mounted to the fire wall. I have 10 relays and 20 circuits.
Attachment 1482725

Re: My 52 GMC Build
 

Looks great..........

Re: My 52 GMC Build
 

nice panel, very clean and organized. gotta luv that. something that takes soo long to do and no one will ever seem to notice. like hey this truck drives sooooo great, must be all that clean wiring!

Re: My 52 GMC Build
 

That's a real clean panel Lower50's!!
I must build myself a new one.....

Re: My 52 GMC Build
 

Thanks Coach
Thanks. True and if and when I need to fix something I will know where to look.
Thanks Kees

Re: My 52 GMC Build
 

Very nice work...Jim

Re: My 52 GMC Build
 

Great work on the electrical panel. Nice layout and very clean! Those poppers are sweet. Kind of makes me want to put some in my 40 Ford.

Re: My 52 GMC Build
 

That is very clean! What are the 10 relays controlling?

Re: My 52 GMC Build
 

Hi Bob, you're build is looking good. I saw a pic posted on Instagram. Are you on there? If you haven't seen it, I'll post it here.

Re: My 52 GMC Build
 

I need to learn a lot about this stuff. Why use relays in place of fuses? If a relay is a switch, what is the difference in powering a box full of fuses with one switch(key switch) or using a bunch of relays with fuse links? I need some quick education. I'm googling what I can but there is nothing specific to auto, or explanations of what and why? I'm kinda dude that needs to know why I'm doing something. Any of your help would be greatly appreciated.

Chance