![]() |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
So yesterday I went to play with the callipers
Started off by cleaning them and seeing of the pistons would even move with pads in place, and a large screwdriver to encourage them. https://hosting.photobucket.com/imag.../IMG_8829.HEIC Removed the pipes. https://hosting.photobucket.com/imag.../IMG_8833.HEIC Then fired up my supersized compressor to drive the pressure through the system to try budge the pistons. Sealed the front end with good old ductape https://hosting.photobucket.com/imag.../IMG_8831.HEIC Ultimately, my skills and the condition of the callipers did not match up. So I will walk away from these, probably try sell them to someone who is a dab hand at refurbishment of callipers to sort out. Then replace the callipers and buy some new pads and hardware. Will get to that next week. Following this I went to the rear brakes. Remember this ? https://hosting.photobucket.com/imag.../IMG_8574.HEIC Would have covered this lot at some point. Missing two studs, and one off the front hub too. Sure there will be some somewhere to buy or scavenge. https://hosting.photobucket.com/imag.../IMG_8834.HEIC Looking decent from here. https://hosting.photobucket.com/imag.../IMG_8836.HEIC Whoooops…… OK, maybe not. So that will be new drums, pads and possibly hardware or a rebuild for the rear. https://hosting.photobucket.com/imag.../IMG_8835.HEIC Also fitted the 4x108 to 4x100 @20mm thick adapters and 5mm spacer. This gets the wheels right out to the edge of the mudguards. I will look at a small engineering solution to replace the wheel nuts the adapters came with, with some studs welded in there, and then some shallow nuts to hold them onto the hubs. https://hosting.photobucket.com/imag.../IMG_8838.HEIC Of course with light failing, I had to at least try the wheels on as well. Seems like everything fits in there, despite the drum being absent. https://hosting.photobucket.com/imag.../IMG_8839.HEIC And some centre caps/cups will need to be sourced at some point. https://hosting.photobucket.com/imag.../IMG_8840.HEIC Today slow day, due to no new parts to fit, will probably be to go back to the body and start working on the screen support for the Land Rover screen @glenanderson donated to the build. Or maybe rip out all the gauges that were fitted before, none of which I intend to use…….. Remember what it looked like when we fetched it. Rear drum in evidence too. https://hosting.photobucket.com/imag...53b68d2828.jpg Centre console not my taste. https://hosting.photobucket.com/imag...3f92805e05.jpg Coffee, then garage. . |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
What?
Weekend over My new DeWalt tools landed. Amazed at just how different they are to the Makita units I have/had. Ergonomics and size/weight is really well balanced. https://hosting.photobucket.com/imag...Render(42).jpg A quick couple of pics about something that is so different for me, here in the UK the way roads are marked. A melted, hot type paint poured from a jug into a drawn trough. https://hosting.photobucket.com/imag.../IMG_8850.HEIC https://hosting.photobucket.com/imag.../IMG_8851.HEIC In other news, mate @paulf came to collect his hydraulic press in his split bus, dyno’d at 170bhp it has to be interesting if driven hard. https://hosting.photobucket.com/imag.../IMG_8870.HEIC While he was here @nickwheeler called me to see if I was here. Of course, so 30 minutes later he joined us. Paul had a home, wife and kids to get to, and left in his bus, and it sounded sooooo healthy. Thanks mate. Nick and I carried on talking all things automotive and tools. Ultimately I managed to convince him to try using the blow out tool he had brought over to see if after my failure, he could convince the pistons to move. Bigger hammer, dismantling and pressure, all failed to get any progress. So we realised that maybe these callipers have seen better days. So the next job will be to put together a package of front brakes and the bits needed. https://hosting.photobucket.com/imag.../IMG_8873.HEIC Regarding the rear brakes, Nick had also brought some parts he had bought years ago and never used. https://hosting.photobucket.com/imag.../IMG_8874.HEIC Looked like it is a fit, maybe this is another of those interchangeable parts one finds when working with cars. https://hosting.photobucket.com/imag.../IMG_8876.HEIC Looking forward to getting some more new parts together to fit before reuniting the chassis and running gear. We are getting there, bit by bit. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Took a very quick look between meetings at the Rallydesign site via a Google search.
Pads seem to range in price widely. Also noticed that prices exclude VAT. Yes you have to pay it but it does show that different companies advertise differently. https://hosting.photobucket.com/imag...Render(43).jpg Rears will be similarly interesting as there are different options it seems. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Yesterday I met my postman about a kilometre from home up on one of the farm roads.
He drove next to me while I was doing my exercise walk. Told me he had delivered a parcel for me, through the letter slot in the front door. International delivery he said. I knew instantly what it was. Vladimir, in Russia had told me in one of our Whatsapp chats that he had put a small parcel in the post for me. So when I got home, the shape gave it away. Russian License plate for my collection. Even better, it falls into my preferred group of different, unusual etc as it is a temporary plate for moving vehicles from one city or region to another. Thick laminated, and flexible so it can be tied on with string. https://hosting.photobucket.com/imag...DB12F1796E.jpg Also included, some working gloves for the garage, a Lenin Lapel badge for my weirdness cabinet, and then a necklace for Sally, so nice in this community that people feel the need to acknowledge the others in our builds. Also in the parcel…….. A horse decoration form the 1800’s that Vladimir found while treasure hunting in a field. Being a Horse decoration, this may possibly become the keyring for the Rezin Rockit. Horsepower and all that. https://hosting.photobucket.com/imag...25B7AAA0C9.jpg Life is good. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Very cool parcel for you. The horse medal goes with your spurs too.
It is neat to see all the truck/car people around the world enjoying each others projects. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Quote:
Blessed for sure. Popped into Kevins place today on the way home from getting a haircut. His build is really getting on now. Not bad for a retired well over 70 and never built a car, kinda guy. He is so energised and excited right now. https://hosting.photobucket.com/imag.../IMG_8960.HEIC https://hosting.photobucket.com/imag.../IMG_8959.HEIC Love these castings. Still to be attached. https://hosting.photobucket.com/imag.../IMG_8961.HEIC Then back to meeting 4/5 for the day. My butt and back hurts. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
[quote author="@westbay" source="/post/2702311/thread" timestamp="1634628750"]Going back to the brakes ...and while the wallet is open ! ... what state is the master cylinder in ?[/quote]
LOL….. You and @pauly make a formidable spending team. https://hosting.photobucket.com/imag.../IMG_8975.HEIC Other side. https://hosting.photobucket.com/imag.../IMG_8974.HEIC https://hosting.photobucket.com/imag.../IMG_8976.HEIC Speaking of brakes, having seen the cost of rear brake drums at around £100.00 per pair, I will need to find out if anyone in the Medway are can stick them on a lathe and clean them up for me. Happy to reuse them if the can be cleaned up. So I took the remaining complete unit apart….. Greasy. https://hosting.photobucket.com/imag.../IMG_8980.HEIC Had thought that part of the brake lining was missing as the other side looked like this. Nope, that is what the look like. https://hosting.photobucket.com/imag.../IMG_8982.HEIC https://hosting.photobucket.com/imag...Render(44).jpg https://hosting.photobucket.com/imag.../IMG_8986.HEIC Was chatting with Tony @westbay earlier about the price of the drums. Looked at the price of shoes…… Crazy. £13.00 for 4 includes shipping. How?? https://hosting.photobucket.com/imag...x/IMG_4892.PNG Hardware/fitting bits are more than the shoes. Guess I need to order the shoes if I can find a machinist. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
DIY CITY……….
Having spoken to mate Darren last night to find out if there are any engineering shops I can use to get the existing drums skimmed, he suggested I come to his shop and put them on one of his lathes on Sunday and start by just cleaning them up as they could pe perfectly servicable under the rust and greasy residue shown. So Sunday will be a bit of DIY and hopefully we get the drums recovered to full function. Shoes for them are surprisingly cheap/affordable. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Been to work this week.
Not dressing in the usual work from home clothes or my favourite garage outfits was a bit weird. Days are getting shorter too, so finding pockets of time for the build or my 6km farm walks gets more difficult. Before breakfast, lunch time or between Zoom and teams meetings. https://hosting.photobucket.com/imag...0B74EC869B.JPG This was todays attempt at stealing time from myself. Knotwheel of Truth @pauly (tm) https://hosting.photobucket.com/imag.../IMG_9072.HEIC Oooohhhh….. https://hosting.photobucket.com/imag...Render(49).jpg https://hosting.photobucket.com/imag...Render(46).jpg https://hosting.photobucket.com/imag...Render(45).jpg Then after the wire wheel, this was the result. Needed more sanding. https://hosting.photobucket.com/imag.../IMG_9076.HEIC https://hosting.photobucket.com/imag.../IMG_9080.HEIC Using the new Dewalt cordless tools felt good, justifying the purchase. https://hosting.photobucket.com/imag...Render(47).jpg Finished. Brake shoes can do the rest of the finishing. https://hosting.photobucket.com/imag.../IMG_9082.HEIC Happy with the result so far. Resuscitated |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
I really wanted to paint the drums and Callipers ORANGE to go with the polybushes………
But patience being one of my absolute virtues, that has been wearing thin lately, I did not want to wait to find Orange, so ended up at three shops that all had Red, Black, Silver in VHT Paint. So by the time I got to Aghabridge at the local industrial site I declined the colours they had, then as I had my hand on the door, I turned around and asked for a can on Simoniz VHT in Red. I may still regret this move, but waiting for Ebay to deliver a can at £15.00 including the postage vs £9.00 for this can……. May be a false economy. Lets see if I can live with it. Blanked off the insides of the drums with my loyal CAD plugs. https://hosting.photobucket.com/imag.../IMG_9097.HEIC Shiny wet paint. https://hosting.photobucket.com/imag.../IMG_9098.HEIC And drying. https://hosting.photobucket.com/imag.../IMG_9100.HEIC Once I order the front callipers, pads and shoulder bolts, they will get painted red as well to match. I really hope it all goes together as I am currently only on Black and Orange, with the Red now added. Stopping in at mate Kevins workshop yesterday He was super excited as he had been given a pair of 60’s VW Beetle front indicators to use as rear indicators on the rear mudguards They need some work as there is some rust under the chrome. However, I also know that the older 50’s Beetles have smaller units that may look a bit nicer and daintier on the rear fenders. Question is…………. Does anyone have decent, complete a set of the older units to sell or donate? Please post or PM me. https://hosting.photobucket.com/imag...541230cf4c.jpg https://hosting.photobucket.com/imag...5ee4c0ddef.jpg Also rescued from Kevins bin, these flaring tools, said to be rubbish. If anyone wants to collect them, free of charge, or pay postage, they are available as a joblot to any masochist out there. https://hosting.photobucket.com/imag.../IMG_9095.HEIC Friday……. Weekend soon. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Glad to see you making such good progress. Looking sharp in the coat & tie!
Your mate Kevin's car is outstanding, I actually think the current vw indicators look right on that size car. But what do I know about British cars... Anyway, Have a GREAT weekend! |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Quote:
Trust all is good with you and the family. You are right, Kevin’s car though pretending to be a Deusenberg is a Jaguar engin in a Rolls Royce. It is a lovely thing, and the fact that he is self taught, right down to the aluminium stretching and upholstering, is pretty impressive. [quote author="@grizz" source="/post/2702767/thread" timestamp="1634973674"][quote timestamp="1634972234" source="/post/2702766/thread" author="@kevins"]There are no seals they rely on the seals in the wheel bearings, to change these you need a slide hammer to get the shafts out and a press to get the bearing and retaining ring on, fortunately bearing kits are only around a tenner. I'd do both if I were you.[/quote]Time to scrap this barsteward of a thing. More tools I do not have. [/quote] So it looks like I am way too committed to this thing. Maybe I should be committed, or get on with it. Just spent some more cash. From the £49.50 per calliper, this is where that ended so far. Brake lines and hardware will add to that of course. https://hosting.photobucket.com/imag...Render(51).jpg I really dislike working with dirty parts, even if they are broken, non functional, or getting replaced. https://hosting.photobucket.com/imag.../IMG_8982.HEIC As a bit of Zen searching last night when I realised that this thing has thrown me another curved ball, I thought wasting a bit of fresh petrol, maybe a liter in total, I would at least clean up the rear drums and their parts. https://hosting.photobucket.com/imag...x/IMG_9156.JPG Result. https://hosting.photobucket.com/imag.../IMG_9162.HEIC Next one. Dry, no leaks, but it will have to be done while I do the other side. https://hosting.photobucket.com/imag...Render(50).jpg And done. https://hosting.photobucket.com/imag.../IMG_9164.HEIC I have decided to step away from the build for today, if I can get it right, and do the hedges and garden beds for the last time this season, hopefully. Maybe cut the grass too. Oh, and see Sally. Nice day out. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Yup…….
I like animals, and love them visiting. George from two houses down spent a lot of time here yesterday while we were clearing up the garden. https://hosting.photobucket.com/imag.../IMG_9214.HEIC https://hosting.photobucket.com/imag.../IMG_9218.HEIC I cut all my hedges, and Mickey’s next door as he hates doing it. Sally cleared garden beds, I raked up pine needles and leaves, followed by cutting the grass. Once all that was done, including going to Sallys place to sell her cross trainer and see it leave she went in to watch Gogglebox, one of her few luxuries that I can’t abide. So I went to the garage for a couple of slow hours to do little jobs. Nothing mechanical, just sorting stuff out, rearranging my carp. Eventually gave up and grabbed a pair of pliers and the Dewalt with a decent 6mm bit……..l Been wanting to do this job since getting the Rezin Rockit. Drilling out all the rivets. Now you see them. https://hosting.photobucket.com/imag.../IMG_9238.HEIC Now you don't. https://hosting.photobucket.com/imag.../IMG_9239.HEIC Fiberglass resin filler for the holes next. I left the steel tabs, for now, they may become part of the fake door latching mechanism. No bootfair, no plans today. May take the S10 for a drive……. Just need somewhere or someone to visit. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Seems cables have been stolen in my area.
Non existent internet and wifi as a result. Phone has a bit of 3G or 4G that comes intermittently. Went for my 6km walk yesterday, what a lovely day. Also gave me time to take a break from the Rezin Rockit. Thames river and Essex. https://hosting.photobucket.com/imag.../IMG_9255.HEIC And looking back toward the Medway river. I love being surrounded by large water masses. https://hosting.photobucket.com/imag.../IMG_9253.HEIC And one of my turning points, where some magic continues to happen. https://hosting.photobucket.com/imag...2A1E1DB3CC.jpg Up closer, changes every day. Hood ornament and mount added now. https://hosting.photobucket.com/imag.../IMG_9258.HEIC Later the day I took the truck, went for a drive, did some shopping and had a guy in a Tesla speak to me, telling me he loved the truck and the sound. The Tesla is his company car and he made an interesting comment, saying is was ultra capable, but has no soul. Quite telling, we as humans do love the advancement of the species, but the visceral qualities of a petrol or fossil fuelled engine still gets us going. The views are always lovely andthe camera does not do it justice. I popped into Kevins on the way home. He has also decided to now go with the VW Beetle indicators on the rear fenders. https://hosting.photobucket.com/imag...6EC6FE3573.jpg All too soon the weekend was over. But the truck made me grin. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Another job that I will hopefully get to soon.
The floor was modified and repaired before I got the car. I am wanting to reinforce, and possibly paint it once done, to match the rest of the fiberglass, to either white, or maybe mask it all and go black on just the floor. A bit ugly right now. https://hosting.photobucket.com/imag.../IMG_9280.HEIC Using some of this impressive fiber filled resin stuff, I filled all the little holes after prepping them and carefully countersinking those (2) I had not gone through completely. https://hosting.photobucket.com/imag.../IMG_9282.HEIC Next step will be a careful rub back with a flat soft block. So that the holes are filled and ready for whatever treatment I decide to give it. Paint, wrap, stickers……. We still need to decide a route for final decoration. https://hosting.photobucket.com/imag.../IMG_9367.HEIC DHL texted early this morning to say they were delivering the front callipers and hardware between 2.54Pm and 3.54pm Looking forward to masking and painting them before fitting over the weekend. I have next Monday, Tuesday and Wednesday off work, so will certainly be spending some time down at the garage. Kettle is on if anyone wants to come help or hinder. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Day job is really getting in the way right now.
And of course shorter days mean that by 6.00pm time is up. Yesterday was a long, busy online day, loads more to do this week. I have about 10-15 hrs of online training to do, 14 modules, each with a 10 question test at the end, and pass mark 90% Still, Mickey knocked at about 4.30pm as I never even heard the couriers deliver despite being here. Happy to say…….. We have parts. https://hosting.photobucket.com/imag.../IMG_9383.HEIC And some of these. https://hosting.photobucket.com/imag...Render(52).jpg Of course shiny and new is lovely. But Red is better. More later. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
So what does £60.00 buy you? Or $83.00 plus shipping.
One of these, without hardware or pads, or paint. https://hosting.photobucket.com/imag.../IMG_9384.HEIC Paint? Oh, and masking up and heating. Heating helps the paint dry faster and more succesfully. https://hosting.photobucket.com/imag.../IMG_9386.HEIC Result. https://hosting.photobucket.com/imag.../IMG_9389.HEIC And then ready for assembly and fitting. https://hosting.photobucket.com/imag.../IMG_9391.HEIC Hopefully I will figure it out when it comes to the assembly and fitting. Any advice and warnings on the reassembly appreciated as always. I do not have @nickwheeler or @kevins and @pauly on site to guide and bollock me when working. Happy with how they came out though, at £180.00 or $250.00 they best be good once fitted. . |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
So there I was doing my daily brisk 6km walk.
Coming back down the last 0.5km I pass two ladies walking an old Labrador, and a cross bred “Labradoodle” that has always been aggressive, goes for anyone that he sees or passes. I always go down and greet him and make a fuss for a few moments, as I really love animals and want him to feel it as well. Yesterday I was trying to set a new target time for the walk, so when Milo the dog went off barking and lunging at me as usual, I gave him a wide berth and kept left. As I passed he lunged and bit me on the upper thigh, hard. Thankfully he seems to have hit the rear pocket of my tracksuit pants. I was livid, and wanted to destroy him immediately. I went off at him, and clearly scared the living daylights out of his owner and the other lady, Labrador owner. I was going to report it to the police in my anger, and pursue his destruction. In the end I calmed down, and later one of my other neighbours popped around to hear what really happened, small village mentality. What does one do in this situation? The owners husband, interestingly has not come to see if I am OK, or apologise. https://hosting.photobucket.com/imag.../IMG_9435.HEIC I was on training meetings till 4.30pm and after that I grabbed a coffee and went down to the garage to try finish painting the chassis that I had spent a part of my lunch break getting started earlier. https://hosting.photobucket.com/imag.../IMG_9426.HEIC So got going again by 5.40 with the Hammerite. https://hosting.photobucket.com/imag...A61DAFD298.jpg By 18.10 it was pretty much dark, and I had turned on the garage lights earlier so that I could finish the painting on the upper side. I also ran out of paint, perfectly when I finished the upper side. https://hosting.photobucket.com/imag.../IMG_9449.HEIC Went to look this morning, not too bad a few spots to touch up where covering is not complete. https://hosting.photobucket.com/imag.../IMG_9457.HEIC Weather is turning, so lets hope it dries nicely before I flip it over. Then we are ready for partial reassembly. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Just a reminder to all who look in here, and care.
It is the yearly Tuba Trucks Toy Drive on November 13 Details copied below. Quote:
|
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Mickey is heavy on tools.
Currently has my wheelbarrow and making sure it doed not come back as taken. On the way home from getting milk and bread this morning I saw these thrown out down the road. Knocked and asked if I could have them. Home owner helped me load them. Free cash again as I knew I would have been buying a new wheelbarrow soon. https://hosting.photobucket.com/imag.../IMG_9461.HEIC Life keeps giving. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Keep an eye on that bite, if you see any infection get your Butt to a Doctor!
|
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Quote:
Or else you release Eve on me :mm: Got the chassis flipped onto its side today. It is not light, despite appearances. https://hosting.photobucket.com/imag.../IMG_9476.HEIC Used the new paint I got this morning. Done. And I am happy with it so far. https://hosting.photobucket.com/imag.../IMG_9477.HEIC Will get Mickey to help me lower it carefully tomorrow. Slow, but progress is still progress. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Mate Andy in Tulsa sent this video clip today.
How to reduce a spring by 2 inches in 10 seconds. https://youtu.be/7h1PZdJ6d6I Need to find out just why he needs this tool. Not that he needs a reason. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Courier rang my doorbell at 8.45 last night.
https://hosting.photobucket.com/imag.../IMG_9510.HEIC https://hosting.photobucket.com/imag.../IMG_9509.HEIC Guess we are in the braking game now. Loads of little pinging springs to go everywhere. Ohhhh…… Best part, I have three days off work. Kettle is on. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Spent a large chunk of time over at Unit Engineering in Queenborough on the Isle of Sheppey yesterday recharging my manliness batteries.
Went to drop off the three remaining bags of blast media that I never used on the chassis, and tomspend time with mate Darren and some car guys. Also went to convert the CAD pattern pieces into 6mm steel plate. https://hosting.photobucket.com/imag.../IMG_9528.HEIC https://hosting.photobucket.com/imag.../IMG_9546.HEIC Darren just bought in a 2.5 meter bed folder. https://hosting.photobucket.com/imag.../IMG_9542.HEIC Amazing how it folds the steel like it was some toilet paper. https://youtu.be/eS7U8hZX_OM Effortless. https://hosting.photobucket.com/imag.../IMG_9549.HEIC Done. https://hosting.photobucket.com/imag.../IMG_9551.HEIC I will trim the plate to fit both in length, width and height before welding it all together. https://hosting.photobucket.com/imag.../IMG_9559.HEIC Triangulated gusset goes at the rear, against the chassis. https://hosting.photobucket.com/imag.../IMG_9560.HEIC Total overkill, but hey….. it is what was there. Suddenly windy and chilly today, 2 T-Shirts and a hoody weather now. . |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Not much done over the weekend, really rubbish weather, rain etc but was busy, and also rested a bit which was nice.
Last night I thought I would sit in the lounge and assemble the front brake callipers while Sally watched her guilty pleasure “Gogglebox” I can’t abide it and don’t get it. Anyway, I ran into problems moments after starting. One pad went straight in, the second one got gently stuck, and despite trying a few times, I decided to put it down as it was dark outside and the light indoors not ideal. So the question is, do I file a minimal sliver off the edge of the backing plates that seem to stick, or am I missing a trick on the reassembly ? I am not good at force. As @nickwheeler would attest to. https://hosting.photobucket.com/imag...Render(54).jpg It has to be a simple solution, surely. Looking at the original calliper again, I just realised that i never added the thin plates that fit behind the pads. This may be the solution. Along with possibly checking to see if the pistons want to go a bit deeper into the calliper. https://hosting.photobucket.com/imag.../IMG_9660.HEIC Could it be this simple? Will head down to the garage a bit later when it warms up. After all, three days vacation means some real garage time. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
The callipers look good in paint.
I would install the shims along with a touch of copper slip on the back of the pads. Once they are sat on those pins they should all align nicely. If too tight, I would file the edge of the pad - just to remove some of the paint build up. hows the dog bite? |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Quote:
Spot on…… All solved with a bit of filing in the vice. The backing plates are guillotined in a factory, and that minimal untidiness on the cut made one plate microspically thicker than it needed to be. Once filled back, easy fit, copper slip and assembled. Dog bite bruise receding. Still pissed at the owners, not the dog. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
I was headed out to go buy a few bits needed for the work planned today.
Just as I was about to leave for town. The doorbell rang, I was out back, and thought it was Mickey next door, shouting at him to come around back, it turned out he was actually on his rear patio too, so I went around and found a cool guest out front. The one and only Nick Wheeler (I do have surname envy) Perfect timing, had he arrived 10 minutes later I would have been down the road in the truck. So we had coffee, cookies, chat and then made our way down to the garage and started to address the brakes. First problem identified was that the back plates are cut by guillotine in the factory, and a small bit of filing back, saw them slip in as expected. https://hosting.photobucket.com/imag.../IMG_9665.HEIC Nick had pre-emptively brought his brake pipe flaring tools and some pipe for us to give making pipes a go. https://hosting.photobucket.com/imag.../IMG_9668.HEIC Man on a mission. https://hosting.photobucket.com/imag.../IMG_9667.HEIC So Nick showed me how to make one pipe, and then it was my turn. How I like to learn. Despite having made up all the nines for the C10 a few years ago, this tool is different and pretty foolproof. https://hosting.photobucket.com/imag.../IMG_9670.HEIC https://hosting.photobucket.com/imag.../IMG_9671.HEIC Then add the hardware (remember it all only goes on one way if you want it to work) https://hosting.photobucket.com/imag.../IMG_9672.HEIC The tool even shows you Operation 1 and then 2 to do the different sides. https://hosting.photobucket.com/imag.../IMG_9676.HEIC Of course if you overdo the pressure like me…… Oooopps. https://hosting.photobucket.com/imag.../IMG_9678.HEIC Cut off and start again, thankfully I had cut the pipe a bit longer than needed. Next job was to do a second brake hose mounting plate. Where do you buy something that is not for sale out there? Grab some plate, copy it, cut to shape with tin snips, drill holes, file nd tidy, fold tabs etc. https://hosting.photobucket.com/imag.../IMG_9673.HEIC https://hosting.photobucket.com/imag.../IMG_9679.HEIC Then time for a break, made some lunch, and then headed down to The local motor spares shop, got the 500mm brake hose identified, and ordered one for tomorrow. Followed by the industrial estate, bought some shoulder bolts to replace the ones I hd bought from Rally Design as the ones they sent were the wrong thread pitch. Followed by a visit to Aghabridge for some brake line fittings, some of which, along with the shoulder bolts, Nick will be trimming back on his lathe at home before we can fit them. Back at home we refitted the drivers side calliper and then the pads, plates, pins, springs and R-clips followed by brake pipes and hose. Pretty chuffed at this point. https://hosting.photobucket.com/imag.../IMG_9681.HEIC And once turned aside the refit went quick. https://hosting.photobucket.com/imag.../IMG_9682.HEIC One more coffee, a discussion about wheel adapters, wheel nuts, studs and lowering and then @Nickwheeler left for his next appointment which he can tell about. A great day, thanks to having help and brains on site. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Todays first job, after having had a lovely holiday breakfast of two fried eggs between slices of toast will be getting into the rear of the garage and removing one strip light I know is fitted to the rear wall.
Once I remove half the C10 parts and load bed stacked in there. Realised that it is pretty much dark by 5.00pm now and by Christmas it will be 3.30pm when play will be halted outside. So fitting the strip lights this morning before heading out to go collect the brake hose ordered yesterday is my plan. Remember when I had less clutter. These lights actually never ended up working. http://i294.photobucket.com/albums/m...ps96ef1262.jpg So hopefully by 11.00 the carport will have three strip lights up, if I can keep my shiit together and not get distracted Day 2 of vacation. . |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Loooong overdue job on the carport built last year done yesterday.
I removed strip lights from inside the garage and mounted them outside in the carport, all individually wired and plugged so that I can select which to run. I had smashed one pair of tubes before when I dropped a light, so headed to the local electrical wholesalers to get replacements, and while out there I got an LED spotlight, going for a 50W unit claimed to deliver 4500 lumens. Should be great for dark time work. https://hosting.photobucket.com/imag.../IMG_9732.HEIC https://hosting.photobucket.com/imag.../IMG_9733.HEIC Went to see how they worked after dark last night. I think they will do. https://hosting.photobucket.com/imag.../IMG_9747.HEIC https://hosting.photobucket.com/imag.../IMG_9746.HEIC https://hosting.photobucket.com/imag.../IMG_9743.HEIC May add one more to the front edge of the carport as well to improve coverage. Happy though. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
So while I fitted the lights, @nickwheeler carried on assembling the other side of the front end with the new hose and cut down bolt and nuts.
https://hosting.photobucket.com/imag.../IMG_9729.HEIC And finally…….. BOOOOMM !!!! SOOO PLEASED TO HAVE IT BACK HERE. https://hosting.photobucket.com/imag.../IMG_9737.HEIC Then we had a coffee and jam donuts to celebrate. Followed by a start up on the rear brakes as the slave cylinders ordered had been delivered in less than 24 hours. Unlike me, Nick does not have a foul sailors mouth, the air around his head was crystal clear once we started disassembly, whereas I was in a puff of blue smoke tinged with frustration. Even the disassembly was just not easy, though I am sure there could be an easy disassembly technique. Once removed…….. https://hosting.photobucket.com/imag.../IMG_9739.HEIC Trying the new ones I had bought off eBay it seemed they just did not want to fit, either on the backing or in the drums. https://hosting.photobucket.com/imag.../IMG_9740.HEIC At this point a reference to the service manuals Nick and dan had brought here before, showed that there are actually two sizes specified…….. 8” or 203mm for the lower spec 1300cc and 9” drums for the 1600, 2000 and 2300cc models. So as luck would have it, I had bought 9” brake shoes, and then the slave cylinders I ordered were wrong too, they have a round mounting on my brakes, but the ones I had ordered have a more oval shape, so do not fit. Guess I have a full set of new, unused parts for sale. Original part number, now need to find a pair. https://hosting.photobucket.com/imag.../IMG_9744.HEIC And the original slave has some almost illegible details. https://hosting.photobucket.com/imag.../IMG_9745.HEIC FRUSTRATED.Com Later, and after dark, the lights seem to be really good, I will add one more just inside the roof on the final beam. Seems shadows will also not be a big problem, maybe. I guess progress is progress, regardless. . |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Some random stuff.
On my daily walk, I have few touch points that end up giving me the 6.3km or almost 4mile walk I do. https://hosting.photobucket.com/imag...x/IMG_9768.PNG Alpaca corner. https://hosting.photobucket.com/imag.../IMG_9764.HEIC https://hosting.photobucket.com/imag.../IMG_9763.HEIC A new farmer has taken over the land lease from the Church, and he is ruthless, greedy and destroying infrastructure as he goes about maximising his profits. The tractors and trucks are ruining the road surfaces that were never made to be used at this scale. 300-450mm deep trenches along the edges as they collapse verges etc. I am not impressed. https://hosting.photobucket.com/imag.../IMG_9767.HEIC Lucky I guess its not my driveway. Waiting for the first cars to land in the trenches. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Not a road trip, but a 4hr trip on the road with a small detour to collect some fiberglass resin, matting, rollers etc from @adam73bgt that he collected for me a few months ago and stored in the back of his MG BGT.
Also stopped at Watford Gap Services for a pee and overpriced Costa Coffee along with the croissants Sally had made for us. Thank you mate for collecting and storage. Easy house to identify. https://hosting.photobucket.com/imag.../IMG_9809.HEIC Then back on the road…… Up to Sandford near Whitchurch in Shropshire to come help mate Craig and Lorraine get some yard work and heavy lifting done. They bought a converted barn house and a bit of paddock that needs a lot of work to get to where they want it. Awesome details, layout and features, including an AGA wood burning stove in the kitchen. https://hosting.photobucket.com/imag.../IMG_9867.HEIC He bought the old stables, enough for 4 horse and tack store and it is getting moved 100 meters to a new spot in the back field, joined later by a garage/workshop Also happening is a new access path through the back being built, purple line…. So petrol head stuff needs doing. Yellow graded access started yesterday, 20 tons of hardcore being delivered on Saturday, so loads of prep needs doing before then. https://hosting.photobucket.com/imag...Render(55).jpg So Sally and I are the extra muscle. Gas tank for heating and cooking had to be installed as the seller is redeveloping the old stables next door in the large paddocks into a new home, stables, riding school etc. So new tank installed https://hosting.photobucket.com/imag.../IMG_9813.HEIC The vintage Massey Fergusson you see working here is the result of COVID 19 when the owner operator lost his job and started his own business. Garden bed, shrubs etc removed. Wall later today. I brought some tools too to help cut back parts of the overgrown garden and access. https://hosting.photobucket.com/imag.../IMG_9826.HEIC https://hosting.photobucket.com/imag.../IMG_9836.HEIC https://hosting.photobucket.com/imag.../IMG_9839.HEIC https://hosting.photobucket.com/imag.../IMG_9842.HEIC Loads of hedges to cut back. https://hosting.photobucket.com/imag...58af19de96.jpg And lawns to cut. Everything is badly neglected and overgrown https://hosting.photobucket.com/imag...78fbc992e0.jpg There is a lot of lawn to cut, another Grizz-job as I do love a good looking lawn. Gas delivery done early this morning. https://hosting.photobucket.com/imag...ccb1001306.jpg Lawns starting to look good too. More today. And shed dismantling plus a glass greenhouse. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
This morning we started at 09.00 and moved about 4 ton bags of roof felt that was on the stables’ roof.
Then transferred and compacted further and into Hippo bags for removal. So I started on the lawn again once the other random jobs were done. Squared off the centre part as a plan was brewing. https://hosting.photobucket.com/imag.../IMG_9896.HEIC And in the mean time Larry had removed a pile of soil from where the new access path and driveway will be going. Next up would be the wall, followed by removing a few more hedge plants and large shrobs and trees. https://hosting.photobucket.com/imag.../IMG_9894.HEIC Eventually I got done with the lawn, the grass was so wet and thick from being overgrown, it took a load of clearing the machine nd basket. I think Lorraine is a bit miffed as it means she needs to do it this way next time. https://hosting.photobucket.com/imag.../IMG_9902.HEIC More work going on all day. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
amazing looking property Grizz - looks like a great project for them.
|
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Quote:
You are right, in English terms it is a great place. With the insanity of the British market right now, they had little choice. I am sure that if they could have a larger piece of paddock land, they would but you have to buy what is available. And this suits their basic needs. Though a ton of work and some cash is needed to pull it back into ship shape. Currently one of the biggest commodities is actually simple hands on deck needed. Next weekend he needs more hands to help pull down the stable black he bought, and to move it 50 meters onto his land. So that is the challenge of living 200 miles away into a new area where you have no friwnds or family to help with simple tasks that do need just extra hands. Wish I could help. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Just a bunch of pics today.
We all did a helluva lot of stuff yesterday and as I said to Craig last night, what we did was a lot more than the sum of its parts. Still, loads of progress. A lot of jobs needed to be done in order to line up for other jobs. After all the lawns were done, the next big task was breakfast at around 11.30, American style bacon, scrambled farm fresh eggs and mushrooms and onions. Then back out to cut backma load of overgrown hedging, trees and other wild growth. Clearing, bagging and more. Ohhh, and with the money saved by changing the roofing felt into the Hippo bags as Craig said, in my typical “Man Maths style” the saving, back into pocket, by recycling or reusing, repacking a Hippo bag left by the gas fitters is £132.50 if they remove it with your bad rubble, and you reuse your own turfs from it, along with recycling the contents. Sally, Lorraine carrie on cleaning and clearing loads of beds that have clearly not seen a gardeners hand in years. Larry carried on shifting soil, prepping for the Type 1 to go down and compacted (Monday) Craig worked, and played Ring Master to all. So in no particular order. Reversing all the way from the A41 motorway up a farm alley road. https://hosting.photobucket.com/imag.../IMG_9929.HEIC We had prepared and laid down some so e of the OSB inner walls from the stables so that the drive did not get too contaminated with the Type 1 https://hosting.photobucket.com/imag.../IMG_9934.HEIC Nicely dropped. https://hosting.photobucket.com/imag.../IMG_9943.HEIC Another job was to cut a gateway for an archway and person gate in the rear hedge and into where the workshop, stables and Craigs new office will go. https://hosting.photobucket.com/imag.../IMG_9953.HEIC Using the digger to lull the plants out, quicker than a spade and axe. https://hosting.photobucket.com/imag.../IMG_9959.HEIC This was one of Craig and Sallys jobs, while I carried on cutting trees, hedges etc. https://hosting.photobucket.com/imag.../IMG_9963.HEIC Trees along the way were cut back so the digger could get through to bring the Type 1 through from the front, remember the purple route on the satelite picture. https://hosting.photobucket.com/imag...51e8788f0b.jpg This was cut back by about a meter, also the rose bushes inside of it, cut out bit by bit and removed. https://hosting.photobucket.com/imag.../IMG_9923.HEIC Larry carried on with hi demolition mission. By day he is a farmer, but since Covid screwed his life up, he does a lot of this stuff, and really does take pride in what he does. Loads of manual lifting, shovelling by hand and checking it was coming together as planned. https://hosting.photobucket.com/imag.../IMG_9911.HEIC https://hosting.photobucket.com/imag.../IMG_9960.HEIC I gave up by 4.45 as my body was huring. Craig and Larry carried on for another hour in the dark, laying the membrane under the new drive, and bringing the first bucket of Type 1 around from the front and spreading it to hold down the membrane till Monday when the whacker plate comes and the stone will be compacted in two layers. After. Dinner, cooked by Lorraine, we headed home fast just after 7.00 pm Absolutely knackered. At our AirBnB there are chickens, cats and a dog called BEAR. She greeted us and came to spend about 20 minutes being loved and loving unconditionally. I love a dog mauling me, not bitting my butt. https://hosting.photobucket.com/imag.../IMG_9976.HEIC Rarely sits still. I was very happy, so was Sally, who wanted to handbag her and Donna the horse. https://hosting.photobucket.com/imag.../IMG_9981.HEIC Today we have yard work, moving a load of numbered plastic boxes, and maybe dismantling a smaller shed so a bigger shed can be built in its place incorporating the smaller shed on the side. Work till 2.00 pm Then head back, shower, clean up and hopefully head out, cleaned up to a couple of local shops, followed by a pub dinner. Of course things can still change dramatically. Later. |
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Looks like a great day’s work- knackered but satisfying to be outside working with your hands - I spend most of the day working with computers and would much prefer to be outside - just need to find someone willing to pay me
|
Re: Grizz's Redneck Express 1966 Chevy Short Fleetside RESTO-GO!
Quote:
We came up early on Thursday. On site by 9.30 Leaving Sunday Craig needs a few extra hands next weekend to just get these stables down and moved less than 100 onto his property. They have the digger for the heavy work and a small trailer. But need more hands really to make the final dismantling safer and ensuring the panels do not get broken as he is rebuilding it all once the new base is down. Anyone got a few spare hours to share/donate to him?? Venue is Sandford near Whitchurch in Shropshire. https://hosting.photobucket.com/imag.../IMG_9895.HEIC |
All times are GMT -4. The time now is 05:44 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com