Re: My 52 GMC Build
Quote:
|
Re: My 52 GMC Build
2 Attachment(s)
Got the rear all pulled apart. The plan is that Monday morning to pull the cab.
Attachment 1449769 Attachment 1449770 |
Re: My 52 GMC Build
don't you just luv taking it all apart when it takes so long to put together in the first place!!!!!!!!!!!
|
Re: My 52 GMC Build
Quote:
|
Re: My 52 GMC Build
5 Attachment(s)
Today I pulled the cab. To all the guys on this forum that have posted this method of lifting the cab. Thankyou!!!!!! Lifted straight and solid.
Attachment 1451103 Attachment 1451104 Attachment 1451105 Attachment 1451106 Attachment 1451107 |
Re: My 52 GMC Build
2 Attachment(s)
Back in the shop, I put the truck on the floor. I made up the K frame tubes and rear 45* supports. The left 45* support is different because the trans cooler is going there. I used 2X4X1/8" tube, frame is 2X5X3/16".
Attachment 1451111 Attachment 1451112 |
Re: My 52 GMC Build
Looking awesome! Must be exciting to be getting ready to put it together one final time.
Posted via Mobile Device |
Re: My 52 GMC Build
Put it together, take it apart, put it together ....folks don't realize how much work goes into a nice build. Good progress!
|
Re: My 52 GMC Build
super dope
|
Re: My 52 GMC Build
Not much to show with pictures today. I finished welding up the inside of the frame now that the cab is off. Also welded the exhaust tip completely on, tabs to hold exhaust to frame and primed frame. Plumed in the temp gauge sensor for the trans and fittings for trans cooler. Should be lots tomorrow!!
|
Re: My 52 GMC Build
5 Attachment(s)
Today I painted the new frame pieces and running board frame. I also finished up the exhaust. Welded in an EGT bung, put the turbo gasket in and sealed up the cup flanges. Then as I put it all together I put wrap on the exhaust. The wrap I used is rated at 1400*. (Note) this is very itchy stuff the insides of my fingers itch like hell. Wear rubber gloves.
Attachment 1451615 Attachment 1451616 Attachment 1451617 Attachment 1451618 Attachment 1451619 |
Re: My 52 GMC Build
5 Attachment(s)
Today I got the transmission cooler mounted and plumed in. Then I got the fuel lines and brake line bent up and fastened. This is the nickel coated line very nice to work with hardest part is getting it straight. I'm trying to get all the under cab stuff done so I can get the cab back on. Maybe tomorrow.
Attachment 1452037 Attachment 1452038 Attachment 1452039 Attachment 1452040 Attachment 1452041 |
Re: My 52 GMC Build
You are flying! Looks good. What transmission cooler is that?
|
Re: My 52 GMC Build
Thanks I get lots done when I work afternoon shift. The trans cooler is a Derale 13950. It can be used by itself and comes with a thermal couple so it just does it's own thing when needed. Also mount it anywhere.
|
Re: My 52 GMC Build
yah your rockin and be rollin soon. I luv the copper nickel line. perhaps you can get that straightner eastwood sells. aluminum line does the same thing.
|
Re: My 52 GMC Build
2 Attachment(s)
Thanks 99 I got the lines close to perfectly straight just took a while.
Well after spending 34 hrs working on the truck last week I got the cab back on for the last time. I mounted the air horn, ran all my power wires to the rear. I also got rid of the old steering and put the new stuff on with the drop tie rods. Attachment 1453821 Attachment 1453822 |
Re: My 52 GMC Build
5 Attachment(s)
Then seam sealed the cab and gave the floor and fire wall a good coating of rubberized rocker guard. I then ran the transmission wires into the cab.
Attachment 1453823 Attachment 1453824 Attachment 1453825 Attachment 1453826 Attachment 1453827 |
Re: My 52 GMC Build
coming together, dang 34hrs a week, that's about my average monthly time I work on my trucks.
|
Re: My 52 GMC Build
Ya I went 100% on it because the cab was sitting out side. I had friday off work so that helped.
|
Re: My 52 GMC Build
man this thing is gonna be sick I like the back half set up
|
Re: My 52 GMC Build
You're getting so much finished up. Man... 34 hours a week is like working two jobs. :lol:
Nice work! |
Re: My 52 GMC Build
Quote:
|
Re: My 52 GMC Build
1 Attachment(s)
Well I didn't think I would get out to the shop last night. I got the rear shock mounts made and installed. I used s-10 shocks. They are angled for 2 reasons. With the air bag over top of the axle it makes the rear very stiff with little pressure so I did not want the shocks to have full power. Also that's the only spot they fit lol. Jumping on the frame at ride height seems good.
Attachment 1454349 |
Re: My 52 GMC Build
I just signed up as a Premium member.
|
Re: My 52 GMC Build
Quote:
|
All times are GMT -4. The time now is 02:32 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com