Re: What did you do to your truck today?
1 Attachment(s)
got my truck back on all fours, brakes ,fuel, air lines done
|
Re: What did you do to your truck today?
Dino
Looks Great!! |
Re: What did you do to your truck today?
That is so impressive!
|
Re: What did you do to your truck today?
3 Attachment(s)
Got the fenders back from the painter yesterday, looking sharp. If you look at the back side of the fender you can see all the small nick where I figure somewhere along its life must have been in a fender bender.
|
Re: What did you do to your truck today?
Well I took ol'blue out for the longest ride I have been on since I have had it on the road.. The wife and I did 100 miles ,and ol'blue made it home .. Even drove through a drownpour and neat lightening show...wipers are next on the list ......
|
Re: What did you do to your truck today?
Quote:
|
Re: What did you do to your truck today?
was a lazy day after yard work I turned the hose on her and washed all the dust off of the old girl,then I took the front fenders,hood,rad support off.need to finish putting plug wires on and start her up after new head gaskets.O well time for a beer there is always next weekend.
|
Re: What did you do to your truck today?
i searched the net for an affordable disk brake kit (with no luck) for my 66 I'm picking up next weekend .
|
Re: What did you do to your truck today?
Almost finished up the rear main seal replace I started yesterday. Need to torque pan bolts, put filter and oil in and fire it up.
|
Re: What did you do to your truck today?
Installed new distributor, coil, rotor, cap, wires, plugs, set timing, repaired my fuel line, GOT MY NEW 63 started for the first time!!!!!! Unfortunately I still can't figure out the fuel issue, the carb is still dry. All I can think of is replacing the fuel pump. But what a relief to hear the engine start. The truck didn't run when I bought it so I am pretty happy not to have to replace an engine.
Posted via Mobile Device |
Re: What did you do to your truck today?
removed and polished my t3 headlights! really!
waiting for my stock speaker so i can install stock radio/speaker... |
Re: What did you do to your truck today?
Quote:
Today I went outside and pulled the cruise parts out and guess what - They won't even fit between the motor and firewall... Oh well, chucked it out... It was the factory vacuum operated thing from the suburban that I pillaged the engine, tranny, and rear end from. Sam |
Re: What did you do to your truck today?
tightened up all my bed bolts, welded a filler for the gas fill place, worked on my interior, and checked everything after doing the rear axle flip and installing a c-notch.
Everything is looking great! Getting ready to make this my DD for awhile..... |
Re: What did you do to your truck today?
Quote:
Thanks. Sam |
Re: What did you do to your truck today?
Today, CB radio install, made a bracket that sits on the floor for the CB, holds CB/mic. Later, welding the cross bard for my rear facing trailer hitch receiver box onto frame, and mounting the box, moving the license plate, adding a slider hitch receiver holder and chain loops.
|
Re: What did you do to your truck today?
Quote:
Not of the actual process....but I can take a couple if you want to see how everything went together..... |
Re: What did you do to your truck today?
1 Attachment(s)
I got my DJM springs yesterday and installed them today looks a little better 3" closer to the ground....Vernski:metal:
|
Re: What did you do to your truck today?
vern lets see a shot from the side..
|
Re: What did you do to your truck today?
dino i love your garage wall!!! somebody has some graffiti skills....:metal::metal:
|
Re: What did you do to your truck today?
Vern Are you gonna use it for snow plow??? You need a little room to go Over the drifts!!!
|
Re: What did you do to your truck today?
Quote:
|
Re: What did you do to your truck today?
1 Attachment(s)
Quote:
Sam |
Re: What did you do to your truck today?
Still working on my bed.
Cut the mini tubs out. Going to use stainless steel tubs. http://67-72chevytrucks.com/vboard/a...1&d=1313460998 http://67-72chevytrucks.com/vboard/a...1&d=1313461090 http://67-72chevytrucks.com/vboard/a...1&d=1313461195 http://67-72chevytrucks.com/vboard/a...1&d=1313461373 http://67-72chevytrucks.com/vboard/a...1&d=1313461482 |
Re: What did you do to your truck today?
Just put on a 6 blade factory steel fan and just ordered a new alum three row rad from champion, next wil be the fat block.
|
Re: What did you do to your truck today?
Quote:
|
All times are GMT -4. The time now is 10:34 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com