![]() |
Re: DURG's Black 65 C10
Outstanding!
Remind me of your wheel/tire sizes for this truck please? |
Re: DURG's Black 65 C10
22x9 and 20x8.5
|
Re: DURG's Black 65 C10
It looks fantastic!
|
Re: DURG's Black 65 C10
just WOW....
|
Re: DURG's Black 65 C10
Doing just a little on the truck. I refurbed the stock shroud. I was thinking about using a metal barrel shroud like on my 62 Impala but it looked like the stock one would be salvageable and fit with the raised crossmember and aluminum radiator. Everything is tight with the front GM serpentine belt setup. I also got the steering column and steering linkage bolted up where it's going to be. This was close everywhere because I did not want to run a heim joint and 3rd universal.
http://i224.photobucket.com/albums/d...psxetxnc82.jpg http://i224.photobucket.com/albums/d...psb2mrpl6r.jpg http://i224.photobucket.com/albums/d...pslhfwzgyu.jpg http://i224.photobucket.com/albums/d...pskstdm7fx.jpg |
Re: DURG's Black 65 C10
Looking good,shes going to make some smoke this summer!
|
Re: DURG's Black 65 C10
I doubt it. I have to do a complete wiring harness install as well as exhaust, brake lines. windshield gasket, bed wood install and a lot more. My time is really limited. Working OT and the boy has travel baseball and basketball. The wife is training for an Ironman in Canada so we will be heading up there for a week. Just really busy. It was enjoyable working on the truck so that is what is important. No timeline. I can retire in 23 months so it may not even be done by then, but that's OK too.
|
Re: DURG's Black 65 C10
Did a couple things on the truck for a change yesterday. Installed the starter, bolted up torque converter, and made a throttle linkage with heim ends on each end and put on double throttle return springs. I got this cool vintage Pepsi cooler from my father in law to take with the truck or my Impala to shows. Usually I see the Coke ones but I thought this one was kind of cool.
http://i224.photobucket.com/albums/d...psycthmyfv.jpg |
Re: DURG's Black 65 C10
Quote:
|
Re: DURG's Black 65 C10
Quote:
|
Re: DURG's Black 65 C10
Quote:
Edit: I found a thread elsewhere that explained. |
Re: DURG's Black 65 C10
Has a mid stop position and keeps the door from over opening and damaging trim strip.
|
Re: DURG's Black 65 C10
I should do this too!
|
Re: DURG's Black 65 C10
Actually ventured out to the garage for a couple minor things. Installed hinges on the PB relocation brackets and installed the Wilwood prop valve. Not much but it's more than I have been doing.
http://i224.photobucket.com/albums/d...psom3jscwf.jpg http://i224.photobucket.com/albums/d...psekflsauo.jpg |
Re: DURG's Black 65 C10
Nice you do such clean work!!
|
Re: DURG's Black 65 C10
Keep chipping away. This is one of my favorites, can't wait to see it compkete
|
Re: DURG's Black 65 C10
May I ask what steering column you used with the factory deluxe wheel?
|
Re: DURG's Black 65 C10
I have a custom length Ididit column.
|
Re: DURG's Black 65 C10
1 Attachment(s)
Been working on truck again. Completed exhaust, brakelines. Popped windshield out and cleaned most of the old sealant off. Put tank back in with an NOS filler neck. Filled power steering, master. Shortened snorkel of a stock top air cleaner and drilled a bunch of 2" holes around the perimeter. I left the factory stenciling on instead of putting holes there. Not 100% sold on this air cleaner top yet though.
|
Re: DURG's Black 65 C10
Always liked this truck build
|
Re: DURG's Black 65 C10
sweet build man it takes a lot of time but man its a sweet ride just re read the hole build up till now keep up the good work .
|
Re: DURG's Black 65 C10
I dig the air cleaner, maybe clean up the holes with a dimple die?
|
Re: DURG's Black 65 C10
I like it!!! Is there a way you could put a flare on the end of the snorkel?
|
Re: DURG's Black 65 C10
Thanks for updating the thread. One of my favorite builds here and an inspiration to keep working on mine.
Happy New Year! Keep warm |
Re: DURG's Black 65 C10
That fan shroud looks fantastic. Did you have to repair any cracks or holes? If so, did you use a JB Weld product or other?
|
All times are GMT -4. The time now is 10:05 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com