Re: SkinnyG's '61 Apache
|
Re: SkinnyG's '61 Apache
Primed the nose, the underside of the steps (so I can weld the reinforcement, then I'll prime the tops), as well as the inside of one of the fenders (so I can flip it over tomorrow). No blasting done today because comedy of activity timing.
https://www.gwellwood.com/wordpress/...20-672x504.jpg |
Re: SkinnyG's '61 Apache
|
Re: SkinnyG's '61 Apache
Finished priming the fender the other day, along with the steps after I welded the brace underneath. No idea if short steps are reinforced underneath or not; can't hurt.
I've been doing more blasting. The left rear fender is blasted, the step supports are blasted, and two bed rails are now blasted. Also filled a couple holes in the bed sides that used to hold something. Well, a couple were for the spare tire mount, but dunno about the others. Started thinking about organizing the air ride next. |
Re: SkinnyG's '61 Apache
Quote:
|
Re: SkinnyG's '61 Apache
I kinda had a hunch that was so. Still, can't hurt, eh?
One more bed brace to blast, and I think I'll be doing the final light blasting of the bed for primer. https://www.gwellwood.com/wordpress/...3s-672x378.jpg https://www.gwellwood.com/wordpress/...4s-672x378.jpg In between the previous sandblasting episodes (waiting for the air compressor to cool, for example), I started placing the Air Ride components. While I initially planned to tuck an air tank or two inside bulbous rear fenders, I ended up placing the kit's air tank on the left side leg of the "X". This frame makes it tricky to place a tank, though it is easier with the bed floor raised. You need to take into account room for the driveshaft, room to plumb the lines, tank servicability, access to tank drain, operation of rear sway bar, serviceability of differential, etc..... The compressor will likely go right where I have it in the picture. I'll be running single exhaust down the passenger side, so no room over there. https://www.gwellwood.com/wordpress/...8s-672x378.jpg |
Re: SkinnyG's '61 Apache
|
Re: SkinnyG's '61 Apache
Finished blasting the last of the bed rails. Also blasted all the metalwork/shrinking marks from the inside of the bed.
Outside of the bed next. Still need to blast the hood, the grill, the headlight bezels, and the cab. |
Re: SkinnyG's '61 Apache
Blasted the outside of the bed, and some parts of the bed bottom I had missed. Next will be to up-end the bed, finish blasting the underside, and then should be ready for primer. I hope. I'm always ready for surprises.
I have about 15 hours worth of time-lapse sandblasting video. https://s3.us-east-2.amazonaws.com/p...1s_mmthumb.jpg |
Re: SkinnyG's '61 Apache
First side of bed parts being primed. Second side tomorrow morning. Trying to work three times as fast.
https://www.gwellwood.com/wordpress/...4s-672x378.jpg |
Re: SkinnyG's '61 Apache
:lol: I need whatever you've been taking :lol:
|
Re: SkinnyG's '61 Apache
Great job SkinnyG!! I could use some of that energy here!! but at over 100 degrees... it makes it hard.
|
Re: SkinnyG's '61 Apache
We're currently around a livable 95°F. I did do a lot of sand blasting when we were at 111°F and everything was on fire.
|
Re: SkinnyG's '61 Apache
In the morning I flipped everything over and did the other side. What surprised me is the bed parts took an entire gallon of Epoxy Primer. Mixed 1:1 with activator, that's two gallons sprayed! At over $200 for both, I can see this truck taking $1000 in primer alone. Wow. I'm pretty sure I put three gallons of primer (and three gallons activator) into the cab and doors, front fenders and nose. Hmmm. Make that $2200 in primer once the cab and frame are done. Wow.
https://www.gwellwood.com/wordpress/...5s-672x378.jpg |
Re: SkinnyG's '61 Apache
Better call Maaco for the paint. They can do a whole car start to finish for >$500 :lol:
|
Re: SkinnyG's '61 Apache
The $500 quality shows, too. :D
|
Re: SkinnyG's '61 Apache
Blasting the hood. This was three or four hours. No, nothing on the other side, just this...
https://www.gwellwood.com/wordpress/...50-672x504.jpg |
Re: SkinnyG's '61 Apache
Four more hours of blasting got me here. Still haven't touched the topside.
https://www.gwellwood.com/wordpress/...15-672x378.jpg |
Re: SkinnyG's '61 Apache
I'm sure it's frustrating not seeing more progress with the time involved, but just think how good it will feel in the end when you get it in epoxy and you know that it was bare/clean metal. Keep up the good work!
|
Re: SkinnyG's '61 Apache
It is slow progress, and I get that. I'm saving myself upwards of the $1800 I was quoted to blast absolutely everything on the truck like I am doing. The blaster cost me $135 and I love it.
The rough part for me is being stuck inside my head while blasting. My brain needs to be occupied; I really struggle with mindless tasks. |
Re: SkinnyG's '61 Apache
Quote:
|
Re: SkinnyG's '61 Apache
|
Re: SkinnyG's '61 Apache
AND picked up some PPG Delfleet paint for the frame when I get done blasting the frame. I don't want to sand the frame, so if I can blast it, epoxy prime it, and then paint it within the epoxy's re-coat window, I won't have to sand. Yay me.
The Delfleet is looking to be a fairly positive paint for final colour too. |
Re: SkinnyG's '61 Apache
Any idea how the delfleet is on rust prevention? I know rust is the enemy around here so whatever works good for keeping rust away on something mainly unseen like the frame is what I'd use regardless of finished look lol.
|
Re: SkinnyG's '61 Apache
It's a polyurethane enamel, so that will be the standard. Polyurethane and an Epoxy primer is about as good as I'm going to get.
Regardless, it lasted 60 years with poo coatings. |
Re: SkinnyG's '61 Apache
|
Re: SkinnyG's '61 Apache
Made a wheeled dolly to move the cab around, as it's next to be blasted.
And then realized I need to add some more brackets to the frame, as it will be blasted after the cab. I also machined the poly cab mounts. The 60-62 cab mounts are different than the 63-66 mounts, the early ones being square, and different thicknesses. My '61 had the 1" mounts on the rear, and 5/8" mounts on the front. Energy Suspension's mounts are both 1" front and back, so I chucked the offending mounts in the lathe, and cut them down to 5/8" for the front. Not sure I'm in love with poly mounts, but here we go. There isn't really other options that I've found, and rubber is a lot harder to cut down than poly. Crap ton of smoke in the air as most of BC is currently on fire. Couldn't see the sun at all this evening, and it was a while 'till sunset. |
Re: SkinnyG's '61 Apache
Don't want to put the cab back on the frame without having Raptor under it.
Can't put Raptor under it if I'm going to weld something on it later. Gotta figure out seats, and gas pedal now. Dang it. |
Re: SkinnyG's '61 Apache
In preparing to remove and blast the cab, I need to locate mount the gas pedal. In order to determine the gas pedal location, I need to mount the seats.
I cut the mounts off the original (trashed) seat, and fabricated a method to attach some Honda Civic buckets. I will be modifying the Civic back seat to be a center-seat/console. https://www.gwellwood.com/wordpress/...42-672x378.jpg |
Re: SkinnyG's '61 Apache
Those seats fit remarkably well.
P. :D |
Re: SkinnyG's '61 Apache
I set them so that the rails are centered on the brackets I made. The seat can go far enough back to touch the back wall. The seat also moves forward enough that even my wife can probably drive it (if she had to).
I fab'd the brackets to place the seat at the same angle that it was in the Civic - one challenge of fitting seats is getting the seat bottom at the right angle to support your thighs correctly. The purists would cringe that I'm not using a bench seat. I totally don't care. (big grin). |
Re: SkinnyG's '61 Apache
Quote:
|
Re: SkinnyG's '61 Apache
That's cool, at this level the purist head would explode anyway. :)
|
Re: SkinnyG's '61 Apache
Drive-by-wire gas pedal mount. This took an entire day. I think it's needlessly complex. Looks good, though....
https://www.gwellwood.com/wordpress/...04-672x378.jpg |
Re: SkinnyG's '61 Apache
Seat belts, also from the Honda Civic. 3x3" 1/8" Shoulder mount washer, to be welded in from behind:
https://www.gwellwood.com/wordpress/...18-672x378.jpg 3x3" 1/8" Floor mount washer, to be welded in from behind: https://www.gwellwood.com/wordpress/...14-672x378.jpg 1-1/2" x 1/4" "L" bracket: https://www.gwellwood.com/wordpress/...44-672x378.jpg Belts mounted (yes, I'll make a cover): https://www.gwellwood.com/wordpress/...33-672x378.jpg Also re-fabricated the turbo oil feed "T." The old one was too short (the turbo feed hindered the cam sensor connection), and did not have any way of removing it (no hex). Old and busted (left), vs soon-to-be-new-hotness (right, unfinished): https://www.gwellwood.com/wordpress/...35-672x378.jpg |
Re: SkinnyG's '61 Apache
Glass removed, decent mounting surfaces:
https://www.gwellwood.com/wordpress/...62-672x378.jpg https://www.gwellwood.com/wordpress/...63-672x378.jpg https://www.gwellwood.com/wordpress/...64-672x378.jpg A bit of rust I need to fix: https://www.gwellwood.com/wordpress/...67-672x378.jpg Cab removed and flipped back to scrape the rest of the undercoating off: https://www.gwellwood.com/wordpress/...68-672x378.jpg |
Re: SkinnyG's '61 Apache
Oil-pressure-sender-turbo-feed-"tee" finished and installed:
https://www.gwellwood.com/wordpress/...69-672x378.jpg Welded some carriage bolts in a few un-needed holes to mount the gas pedal bracket, welded up the gas pedal linkage opening, and added nutserts for the fuel pressure regulator: https://www.gwellwood.com/wordpress/...75-672x378.jpg Patch. Will be welded once I've blasted and epoxy primered inside: https://www.gwellwood.com/wordpress/...70-672x378.jpg https://www.gwellwood.com/wordpress/...73-672x378.jpg I "think" I'm ready to blast and prime the cab. |
Re: SkinnyG's '61 Apache
Skinny,
Seen a few people use the oil pressure sender as the take off for the Turboooooo now rather than the blanking plate above the oil filter. Was there a specific reason for this or just easier packaging? Still a while away from having to make this decision but like to understand why people take a certain route. Good progress as always. P. :D |
Re: SkinnyG's '61 Apache
The blanking plate above the oil filter feeds the oil cooler, and is on totally opposite side of the motor. Not the easiest to get to, and snaking the feed line all the way over there seemed risky to me. I want the line to avoid any extra heat.
I don't believe it matters one bit. Pressurized oil is pressurized oil, and the sender is getting the same oil and pressure that is at the filter. |
Re: SkinnyG's '61 Apache
We had some rain recently, and the ground was still too wet to start blasting the cab.
So, I did some blasting in my blast cabinet, after changing the gun: https://www.gwellwood.com/wordpress/...82-672x378.jpg https://www.gwellwood.com/wordpress/...84-672x378.jpg This in addition to the altered siphon-feed on the bottom of the cabinet, and this cabinet is freaking awesome. I love it!! I had not yet epoxied the hood supports, so after blasting a few more items in the cabinet, I sprayed them: https://www.gwellwood.com/wordpress/...86-672x378.jpg I am going to hide the air ride gauges behind the ashtray door. I cut off the back of the ashtray, and experimented with card stock to find the shape and position I wanted using a CNC-Plasma-cut gauges plate I made at work: https://www.gwellwood.com/wordpress/...76-672x378.jpg https://www.gwellwood.com/wordpress/...77-672x378.jpg https://www.gwellwood.com/wordpress/...78-672x378.jpg Folded up and TIG'd together, the gauge plate screws on from behind: https://www.gwellwood.com/wordpress/...79-672x378.jpg https://www.gwellwood.com/wordpress/...80-672x378.jpg Then I had to figure out how to make the ashtray open again: https://www.gwellwood.com/wordpress/...81-672x378.jpg Which I did by making my own hinge and door: https://www.gwellwood.com/wordpress/...87-672x378.jpg https://www.gwellwood.com/wordpress/...97-672x378.jpg Which reveals like this (roughly driver's seat - cab is on its back right now): https://www.gwellwood.com/wordpress/...95-672x378.jpg |
All times are GMT -4. The time now is 01:55 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com