Re: Dutch '59 Fleetside Longbed
Steve-W, it's a tool that manually bends sheetmetal.
Google "sheet metal brake" and you know all about it ;) Sure I know Prins Trucks, just got my parts from him... Two parts missing and one part wrong, send an email, no answer yet. But I'm sure he will solve this. I don't need it to be original, if it's good it's good! I am a Hot Rodder by life :metal: If I can make the parts, I make them, and also the car isn't going to be original ;) I always say: If you drive 80 mph, you don't see it anyway!! On to todays business: Got the lower left cowl and a piece of the floor repaired, not in one day to be honest, it's pretty time consuming, you know that! Made the triangular piece of the inner cowl: https://lh4.googleusercontent.com/-O...o/P1260313.JPG https://lh4.googleusercontent.com/-b...o/P1260314.JPG Then I made the floor: https://lh4.googleusercontent.com/-b...o/P1260315.JPG https://lh4.googleusercontent.com/-V...o/P1260316.JPG Then on to the difficult part.... First I made a 2 mm thick plate for the hinge: https://lh4.googleusercontent.com/-i...o/P1260317.JPG Then bend and knocked the outside of the pocket (1,5 mm thick): https://lh4.googleusercontent.com/-h...o/P1260318.JPG Then the inner piece and bottom (1,5 mm thick: https://lh4.googleusercontent.com/-3...o/P1260319.JPG https://lh4.googleusercontent.com/-w...o/P1260320.JPG I bolted the fender on for reverence of the lower bolt, and made this bolt support out out 2 mm thick plate: https://lh4.googleusercontent.com/-v...o/P1260321.JPG The bolt support has a reinforcement above the bolt hole. Looks like I had thought about it....;):lol: https://lh4.googleusercontent.com/-T...o/P1260322.JPG At last I tacked the cowl cover back in place.... https://lh4.googleusercontent.com/-e...o/P1260323.JPG Next time is finish welding the cowl and grind everything a little smoother. And hope to get the driverside floorpiece ready. After that its only some small parts to be repaired. So Niels A., if you read this......I'm going pretty fast :metal::lol::lol:;) Oh, do I use too many pictures for you guys and girls??? |
Re: Dutch '59 Fleetside Longbed
Never too many pictures!
|
Re: Dutch '59 Fleetside Longbed
Real nice job on the repairs.
Kim |
Re: Dutch '59 Fleetside Longbed
Love the pictures Kees! Nice work, takes a lot of time.
|
Re: Dutch '59 Fleetside Longbed
Thanks guys!!
It sure takes a lot of time, but it's fun to do! |
Re: Dutch '59 Fleetside Longbed
Kees, nice job on the repairs, looks good and nobody will see that it's not stock looking..Jim
|
Re: Dutch '59 Fleetside Longbed
Way to go Kees!! looks great..
|
Re: Dutch '59 Fleetside Longbed
Never too many pics!!! you must have a GoPro connected to your headband while you work..... taking pics as you go!!! lol
I always forget to take pics of what Ive done till Im ready to walk out of the garage at night and then I remember..... :lol: |
Re: Dutch '59 Fleetside Longbed
Haha, no GoPro, just a lot of time-outs :lol::lol:
Remember my teabag cups centercaps in the back? Well, I've come up with an idea for the front.... See the sketch, the teabag cups and the aluminium... https://lh4.googleusercontent.com/-u...o/P1260324.JPG A lathe and some time...Action shot (without the GoPro;)) https://lh4.googleusercontent.com/-N...o/P1260326.JPG One finished: https://lh4.googleusercontent.com/-q...o/P1260327.JPG https://lh4.googleusercontent.com/-e...o/P1260328.JPG The case slides over the center of the hub, set them with 3 setscrews, that's all. I've made two of them, hope they fit, don't know yet. If I made a good sketch and measurements they will fit... We'll see monday :smoke: |
Re: Dutch '59 Fleetside Longbed
That's some cool stuff.
Kim |
Re: Dutch '59 Fleetside Longbed
Very cool Kees!!!
|
Re: Dutch '59 Fleetside Longbed
Love the machining work!
|
Re: Dutch '59 Fleetside Longbed
Thanks Kim, Mark and Doug!!
Went to the truck today, couldn't resist ;) Tried my machinework on the front hubs... https://lh4.googleusercontent.com/-S...o/P1260334.JPG https://lh4.googleusercontent.com/-8...o/P1260335.JPG https://lh4.googleusercontent.com/-h...o/P1260336.JPG Doesn't look too bad, just have to make the hubs black. Finished welding the cowl, so that right corner is ready inside and out :metal: https://lh4.googleusercontent.com/-U...o/P1260341.JPG Remember I had to cut the steps for the LPG fueltanks? I did weld the steps today. First a template from cardboard: https://lh4.googleusercontent.com/-X...o/P1260337.JPG Then to metal: https://lh4.googleusercontent.com/-6...o/P1260338.JPG Bent and drilled the hole thing and welded it in: https://lh4.googleusercontent.com/-w...o/P1260340.JPG https://lh4.googleusercontent.com/-1...o/P1260342.JPG I did both sides, so that ready too :metal: Also take a look at the driverside cowl, I thinks it's all original :c2: https://lh4.googleusercontent.com/-C...o/P1260330.JPG Not bad huh!?! Now I need your advice on the driverside floor. I marked the floor with a blue pen. Those parts I want to replace. I could only repair those parts, but I rather will do the mid section of the floor, from step to transcover. But at the point where the two floor pieces meet, there is at the underside a "reinforcement", a little piece of angled steel, from the cabmount to the transcover. I measured the thickness, it's about 1 mm (gauge 19?) https://lh4.googleusercontent.com/-R...o/P1260333.JPG For the floor I will use 2 mm thick plate (gauge 14). My question: what if I replace the floorsection without that small piece of reinforcement? Do or don't? |
Re: Dutch '59 Fleetside Longbed
Quote:
|
Re: Dutch '59 Fleetside Longbed
Nice fab work.
I probably wouldn't worry about the small piece of metal. the floor gets its stiffness from the beads that are in it. Kim |
Re: Dutch '59 Fleetside Longbed
PTC, I'm not sure, but it looks like an extended piece of the cabsuport.
Kim, If I make a 2mm thick floor, I don't get the beads in it... |
Re: Dutch '59 Fleetside Longbed
Kees...My 2 cents worth, cut out the large section as needed. Check if for sure that is a brace/support. If so, you will be using a heavier gauge metal to replace it. You may not need the brace under it but check if it flexes more than your comfortable with and if it does make a new piece and weld it in. ( don't sweat it so much it can all be fixed my friend ;) )
|
Re: Dutch '59 Fleetside Longbed
Well, it is a cabsupport. I remembered Kim57 did make his own floor, so I looked at his pics (again ;))
His thread is almost a encyclopedia to me :lol::lol: Thanks Kim!! I cut the floor out, and saved the brace. I made the floor in three pieces: https://lh4.googleusercontent.com/-V...o/P1260343.JPG Here you see the brace I'm talking about. https://lh6.googleusercontent.com/-0...o/P1260344.JPG https://lh4.googleusercontent.com/-J...o/P1260345.JPG Of course I have to clean the welds, but I have a good solid floor now. Maybe took away more than necessary... Also closed some holes in the firewall (brake and clutch and one above the transcover) I also made a template to close the rear cabcorners from the inside: https://lh6.googleusercontent.com/-_...o/P1260346.JPG That's for next time!! |
Re: Dutch '59 Fleetside Longbed
Nice job on the floor repair. Should be nice and strong.
Kim |
Re: Dutch '59 Fleetside Longbed
Nice work on the floor, cab corner work looks very familiar!
|
Re: Dutch '59 Fleetside Longbed
Now this is an excellent idea!!! You need to make a bunch of these and start selling them.... This is one area that needs help, imagine all the things in your cab that can get lost in those corners!!!!
https://lh6.googleusercontent.com/-_...o/P1260346.JPG |
Re: Dutch '59 Fleetside Longbed
Not my idea ptc!!
I stole it from the board here ;) Thanks to all on this board!! You've been 9and are) a great help, even you don't know it :lol::lol: |
Re: Dutch '59 Fleetside Longbed
Made the inner cabcorners and tacked them in:
https://lh4.googleusercontent.com/-9...o/P1260349.JPG https://lh4.googleusercontent.com/-s...o/P1260350.JPG Cheap *ss as I am, didn't wanted to buy new lower cabcorners, so I made the myself.... The damage wasn't that big https://lh4.googleusercontent.com/-f...o/P1260351.JPG made them out of 1,5 mm steel https://lh4.googleusercontent.com/-z...o/P1260354.JPG https://lh4.googleusercontent.com/-o...o/P1260355.JPG Left side almost ready, probably don't need to use any bondo. Or just a tiny bit... We'll see, just ran out of welding wire.... |
Re: Dutch '59 Fleetside Longbed
Nice work on the corner. Won't need much, if any, filler. Are you going back with the same blue paint?
|
Re: Dutch '59 Fleetside Longbed
No, not blue.
I'm in love with this one: https://lh4.googleusercontent.com/-A...311-no/876.jpg I believe it's won the truck of the month contest on this board back in 2008? I've doubted a very long time about colors, but I now go with semi gloss black and high gloss red, with some small white striping. I'm not sure about the inside tho, thought about gloss black and only the front of the dash red.....Any input would be appreciated here! |
All times are GMT -4. The time now is 04:57 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com