![]() |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
I had not anticipated just how badly I su<k at fabrication, still working on the glovebox :eyeroll:
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Almost done the exhaust...need another support hanger on each side.
But I couldn’t wait to hear it with the 4” side pipes. https://youtu.be/vtFRFWl6ngs?si=RvuSBsvg6Q9I7DJR I also installed the pressure sender for the new oil pressure gauge, as the stock one still reads about 40psi when the truck wasn’t running. Need to pull the cluster out, and work on that, but I gotta clean up the shop first...metal work is so messy. |
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
Trying to free up space in my shop so I can move the truck in. So I painted a set of ralleys and mounted some used TA radials to make it a roller. Then adapted a squarebody seat into it. Baby steps.
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
installed a 1 1/2" shorter steering column and lowered the seat 2" with aftermarket brackets. Much more comfortable to me.
|
Re: What did you do to your truck today.The 3rd chapter
4 Attachment(s)
Tonight I replaced the bearings and races. Got the bearings packed and the brake rotors installed. Installed the calipers and pads and new brake hoses.
I still need to bleed the brakes, grease ball joints and tie rods and install cotter pins. But I had to put the tires on and see if it sat different with new springs. I put 1” lower springs and removed a 1” spring spacer up front. There was 8” between tire and fender and now there is 6”, math never fails. Lol. I plan to replace the 27” tires with 31” tires, so that will get it down to a 4” gap. |
Re: What did you do to your truck today.The 3rd chapter
4 Attachment(s)
Finished the exhaust on the truck.
I'm not a welder, but it shouldn't fall off anyways... |
Re: What did you do to your truck today.The 3rd chapter
novax522, nice work, but your upper a-arms are on the wrong sides. It's a common mistake.
Good luck, Rg |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Great job, that looks much better. The alignment shop would have found it, but it would have cost you!
|
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
"what did you do?.... sadly, nothing on the trucks in quite some time. Maybe once all of this certainteed siding and Rockwool insulation is installed on the house, then it will be back to trucks.
How many do you spot? |
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Quote:
|
Re: What did you do to your truck today.The 3rd chapter
Got all the tie rods, ball joints, idler, and pitman nuts snugged and cotter pins installed. Got everything greased. It doesn’t sound like a lot, but it took a while.
|
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
finally found a great 1157 LED bulb that is bright, fits and performs...and reasonably inexpensive. Amazon has them in stock at their fulfillment centers so shipping is fast.
My comparison pic doesn't represent the performance perfectly, as photographing a bright light source is very challenging and it blows out the image. Backstory: I didn't want to swap out the OE lens with one of those printed circuit board type lenses to get some brightness to the back. So over the past year, I have gone thru and tested numerous 1157 LEDs with little success. Many bulbs will not even mount in the socket as they bottom out before you can twist it to get it secured. Others were nearly hyperbright and had not brightness differentiation when you hit the brake pedal. The last ones I had, where the Sylvania 1157s that anyone can purcahse at any autopart store. These worked, but were dim in the standard "on" position, in fact dimmer than incandescent. In short, if you want to be seen from behind when you hit that brake pedal, and still have better than OEM brightness when just cruising, these are the ones! We'll see how long they last! |
Re: What did you do to your truck today.The 3rd chapter
1 Attachment(s)
Took the Bomber for one last spin today before the snow hits and the salt gets laid down.
It's almost unheard of in Connecticut for it to be this late in the season with no snow yet, so luckily I was able to enjoy driving it for this long till spring. |
Re: What did you do to your truck today.The 3rd chapter
Great looking pickup
|
Re: What did you do to your truck today.The 3rd chapter
2 Attachment(s)
Started on the rear brakes today. Got one side done, also need to make new rear brake lines.
|
Re: What did you do to your truck today.The 3rd chapter
3 Attachment(s)
Got the driver side brakes done and both sides adjusted. Took before and after pictures.
|
Re: What did you do to your truck today.The 3rd chapter
4 Attachment(s)
Started on the rear brake line. There was nothing wrong with the existing brake line, other than it looked like crap. I had some leftover brake line material from when I redid the brakes on my elCamino. It is a copper/tin alloy. No rusting and super easy to bend. Got one side done tonight.
|
Re: What did you do to your truck today.The 3rd chapter
^ I like that NiCopp line. I'm considering replacing the 54 year old line on my truck with it, just for general principles.
|
All times are GMT -4. The time now is 04:43 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com