Re: S!ck5 65 rebuild
Thanks I'll check it out..
Any going to the 99 speedway sunday |
Re: S!ck5 65 rebuild
Looks good. Will the 64-66 bed wheel wells not fit? I just picked up a steel floor the other day. Do you have any more pics of how you put the bed floor in?
|
Re: S!ck5 65 rebuild
I made a mistake cutting the back corners to much.for me since I have raised my floor I cut about an inch on all cross beams under that bed floor. Then notch out the back corners.
On the install you have to remove one side Of the bed. And you need 67-72 wheel tubs 60-66 too small |
Re: S!ck5 65 rebuild
1 Attachment(s)
Getting **** moving. See you guys at brothers soon
|
Re: S!ck5 65 rebuild
1 Attachment(s)
Trying something new.!
|
Re: S!ck5 65 rebuild
Looks pretty good!
Quick question though, off subject but you don't know the diameter of the tube used on your porterbuilt bridge do you? |
Re: S!ck5 65 rebuild
I got a 65 GMC as well and am in the process of swapping out the 305 for a 350. Where did you get the wiring harness for the conversion? Thanks for the info!
:gmc2: |
Re: S!ck5 65 rebuild
I think it's an inch.but I can check
|
Re: S!ck5 65 rebuild
American auto wire... Charlie
|
Re: S!ck5 65 rebuild
Quote:
|
Re: S!ck5 65 rebuild
Thanks for the info.
|
Re: S!ck5 65 rebuild
2 Attachment(s)
Added the side mounding and working on new spot for the accuair
|
Re: S!ck5 65 rebuild
Quote:
|
Re: S!ck5 65 rebuild
Quote:
|
Re: S!ck5 65 rebuild
Quote:
No problem on the size! It was good to see you again too. I'm going to try and see you guys more at the shows and what not. I was wondering about the size so I have a good variation of dies for my bender. I thought it was 1.5 .120 but apparently 1" is large enough. |
Re: S!ck5 65 rebuild
Well your in luck since I hade pull the transmission out I can see what size is it. I'll do it tomorrow after work
|
Re: S!ck5 65 rebuild
Quote:
|
Re: S!ck5 65 rebuild
Quote:
|
Re: S!ck5 65 rebuild
So far you need tube size on the bridge right
|
Re: S!ck5 65 rebuild
Quote:
|
Re: S!ck5 65 rebuild
1 1/2 hardest454
|
Re: S!ck5 65 rebuild
Thank you! Greatly appreciated!
|
Re: S!ck5 65 rebuild
3 Attachment(s)
working on my Accuair project. Most people have it installed under the bed. But i like the look of it on top of the bed.
I need to remove the the tank. reinstall new 3/8 air lines. i have 1/2 at the moment. I really wanted to buy the accuair au4 tank mount but dont have the cash. so i fig i would try to build my own. here some picture of the mount. |
Re: S!ck5 65 rebuild
anyone know if its a good idea to weld on to the air tank? i got a few ideas for the airtank mount. using a chain to wrap around the airtank then from the chain to the accuair mount. just need to remove the tank and try it out
|
Re: S!ck5 65 rebuild
waiting on porterbuilt stuff sucks lol
|
All times are GMT -4. The time now is 01:31 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com