Re: 57 Chevy Wagon - Californa Dreamin'
Thanks, guys. In retrospect, I should have used 1/4 plate, as the 1/8 was a bit flimsy. But other than that, it worked great. I figure it would have cost a lot more to have HRE do the work, so I saved a few bucks and ended up owning the tool to boot. I probably wouldn't use it to pull an Allison or any other extra large, heavy transmission but for the 4L70E it was just right.
|
Re: 57 Chevy Wagon - Californa Dreamin'
Great work! Now you'll have it in the way, and bothering you. Just wishing someone would borrow it. (wink, wink, nudge, nudge, say no more)
|
Re: 57 Chevy Wagon - Californa Dreamin'
Quote:
|
Re: 57 Chevy Wagon - Californa Dreamin'
2 Attachment(s)
Dual 11" Spal fans are mocked up. It was tricky getting them packaged in the available space, but they're gonna work. I had to give in and take the fan shroud/support to a local machine shop (Lindsay Machine) to have the circles waterjet cut. I fixtured the material up on my little mill but didn't have the right tooling for the job. Took the part to them on Friday and it was done this morning. They also cut the bolt holes in the exact locations as well. Went together like a Swiss clock. Their WJ machine is accurate to .0001" which is much more precise than I figured it would be. Technology - you gotta love it.
Making progress on the wiring front as well. The Holley Terminator X Max harness needed some revisions to a few of the Metri-Pak plugs. Also, some of the wires were either too long or too short, so those have been modified. Now I just need to get the harness situated. I drilled and tapped the driver side fuel rail for a fuel pressure transducer. The Holley software will use the input if it's available. I had planned to thread the sender into the regulator, but the harness dictated that I place it up front near the throttle body sensors. I didn't want to tear the harness that far apart to relocate the plug so this will have to do. |
Re: 57 Chevy Wagon - Californa Dreamin'
2 Attachment(s)
After all the work I did to weld in the high flow cats, I was finally ready to install them. When I got everything in place, the flanges at the front of the mufflers where the v-band clamps fit had about a 1/8" gap on both sides. There was no way the band would draw the flanges together enough to seal up. It seemed the only solution was to remove both sides and lengthen the tubing the amount I needed. However, after I pulled the assembly off the passenger side and started to remove the driver side, I could tell that without being attached via the H-pipe, it fit perfectly. I lightly tightened the muffler clamp and the exhaust manifold flange bolts with no issues.
So, I carefully reassembled the passenger side and found that back to the H-pipe, it was right on the money. From the H-pipe to the muffler was a different story. I had a bit over 1/4" gap now. It appeared that the muffler on the passenger side had moved back after I originally disassembled the tubing. I knew I'd scribed marks on the tubing to make sure the cats didn't alter the overall length. The good news was that I only needed to modify one side. I cut a 3/4" section out of the tubing between the H-pipe and the muffler flange and replaced it with a 1" section. Fits fine now. The fan assembly is finished and the radiator + a/c condenser and lines are back in. The Terminator X Max is mounted under the dash and the wiring is nearly complete. I'm about ready to set it back down on all fours again. By the first of next week, it should have the intake on and hopefully in the not-too-distant future will be ready to fire up. |
Re: 57 Chevy Wagon - Californa Dreamin'
5 Attachment(s)
Got sidetracked a bit. A member of another forum suggested that it might be a good idea to add a heat shield around the cats to protect the transmission and floor pan from the high heat. Seemed like a really good idea, so I got to work.
I have the heat shield on one side complete and installed. Haven't started on the other side yet. Kathy asked me to assemble her new Christmas tree and fix a couple of her music boxes she sets out for the holidays. That takes precedence over car stuff this time of year. I didn't have a piece of stainless sheet in my scrap bin big enough to make the shield in one pass, so I sandwiched two pieces together. It's .037" thick material so it will probably twist up like a pretzel when it gets good and hot, but it should be sufficient to serve as a barrier to the heat radiating from the cats. |
Re: 57 Chevy Wagon - Californa Dreamin'
Looks good Vic!
|
Re: 57 Chevy Wagon - Californa Dreamin'
Quote:
|
Re: 57 Chevy Wagon - Californa Dreamin'
Looks great, Vic!
|
Re: 57 Chevy Wagon - Californa Dreamin'
1 Attachment(s)
Quote:
A buddy sent me this which explains a lot if you cut your teeth on a stick shift. ;) |
Re: 57 Chevy Wagon - Californa Dreamin'
Haha...that's a good one..
|
Re: 57 Chevy Wagon - Californa Dreamin'
2 Attachment(s)
So, a couple of weeks have passed during which I finished up the do-over on the EFI. The Terminator X Max controller just barely fit into the space where the other controllers sat in the past. I not only had to build stand-offs to position it further away from the firewall, but also had to machine some long hold downs to attach it. Couldn't get my fingers into the available space to start regular nuts. But after all that, it's in and wired up. I also spent some time revising the fuel lines. None of the lines fit after I modified them for the dual quads. The upside is that I repositioned the regulator and fuel pressure gauge for better access. I tested it for leaks and to my surprise, I didn't have a single one. Usually, there's at least one fitting that requires a bit more oomph to seal it up.
I had a local Holley expert, Andrew Borodin, over to the house last week to help me with the initial startup calibration. He also gave me a wiring diagram for the IAC kick and AC shutdown relays. The software will temporarily boost the idle when the AC is turned on and shut the AC off at a specified throttle position (like 75% WOT). He spent about an hour going over the fuel and spark tables explaining them and making some tweaks. My short-term memory is so shot that I don't remember a lot, but I was impressed with his knowledge. He'll be back when I'm ready to fire the engine the first time with this new setup. Said it will take another hour to tune the engine for best performance. It's turned cold so I'm planning to wait for the next warm day. Meanwhile, I have a new project to keep me occupied. I decided to punch louvers in the side panels I made for the inner fenderwells. I'm thinking ahead to the summer and doing all that I can to help lower the under-hood temps. I did some research on commercially available dies and they're pretty proud of them. While online, I ran across a video showing a homemade set of dies and I'm going to give it a try. I only need to punch a couple of dozen louvers, so I don't need tool steel. I'll show you the results - good or bad. |
Re: 57 Chevy Wagon - Californa Dreamin'
That's a lot of wires, they make my brain swim looking at them! I can't wait to see the louvers.
|
Re: 57 Chevy Wagon - Californa Dreamin'
1 Attachment(s)
Quote:
|
Re: 57 Chevy Wagon - Californa Dreamin'
Looks awesome Vic, wiring job looks super clean!
|
Re: 57 Chevy Wagon - Californa Dreamin'
Quote:
After about two hours of shop/driving time Andrew had the engine running like a little sewing machine. The trans works great too. It's hard to tell if the cooling system issues are completely gone because the ambient temperature was much less than it was last summer. However, in the shop, fan 1 would come on briefly and then cycle off less than a minute later. So, the switch to the 11" Spal units seems to have been worth it. On the road, the temp stayed at 183 (180 degree thermostat) and the trans temp never got over 160. Tripling the size of the trans cooler was probably a good move too. I have a few remaining minor things to do, and then we'll be ready for cruising. Back to my louver project... |
Re: 57 Chevy Wagon - Californa Dreamin'
That’s great too hear, sounds like it will be smooth sailing. You’ll definitely will be bringing home some hardware whichever show you go to with that beauty!
|
Re: 57 Chevy Wagon - Californa Dreamin'
5 Attachment(s)
Quote:
The louver project is halfway done. The dies are finished, and I tested them on a piece of scrap aluminum. I plan to use the homemade English wheel that I was given by good buddy, Jonathon Cornell. I think I can remove the wheels and locate the dies, so they punch thru the aluminum sheet consistently. I'll post photos of the setup when I've sorted it out. |
Re: 57 Chevy Wagon - Californa Dreamin'
If nothing else, there's always A2 and the good 'ol redneck heat-treat. Got any used motor oil?
Heard you got with Andrew, glad it went well and the gorgeous wagon is gonna go down the road! |
Re: 57 Chevy Wagon - Californa Dreamin'
1 Attachment(s)
Quote:
I think the dies will work pretty well for the little dab of work I have planned. My test piece was a louver I cut from a leftover panel I used as a pattern and it's a little ragged around the edges. Below is a louver I actually punched out of a fresh piece of .063 aluminum with the dies I made. |
Re: 57 Chevy Wagon - Californa Dreamin'
That looks great Vic...nicely done
|
Re: 57 Chevy Wagon - Californa Dreamin'
Nice looking set of dies you made. The test louver looks good.
|
Re: 57 Chevy Wagon - Californa Dreamin'
3 Attachment(s)
Thanks, guys. I finished my homemade louver press. The "English wheel" I used as the frame for it deflected too much, so I had to tack a piece of channel to the front of it make it solid. If I ever need to use the wheel, I can zip the channel off with a Dremel cutoff tool.
After getting the dies aligned, I punched a test panel. Looked pretty good, so I proceeded to the real thing. Both side panels are now louvered and ready to prep for self-etching primer and a coat of matte silver to match the fenderwells. The anodized finish was pretty close to the rest of the inner fender, but it was hard to keep clean. The painted surface is much more forgiving. Hopefully I can get a decent color match but regardless, it should be better than what I had. I'm not sure how much the louvers will help, but I don't reckon they can hurt. I believe the best mod I made was the larger, more powerful fans, but summer will be the real test. |
Re: 57 Chevy Wagon - Californa Dreamin'
Very nice!!!!!
|
Re: 57 Chevy Wagon - Californa Dreamin'
I like the louvers a lot....
|
Re: 57 Chevy Wagon - Californa Dreamin'
Thanks!
I put one of the panels in temporarily to see how it looked and I think it works pretty well. Today I'm prepping the panels for epoxy primer and matte silver paint. Weather is a bit cool, but I can spray outside then bring the panels back in to warm up. I have a heat gun setup to force dry them a bit. I'll post pics when I'm finished. My buddy Chip called me this morning to let me know his dad, Vern, passed away yesterday evening sitting in his easy chair. Vern (or Boppa as many knew him on the forum) was a dyed in the wool truck guy. I talked to him just yesterday and we had plans to go for coffee and sandwiches after the first of the year. Ya never know what the day holds for you when you crawl out of bed. I realize it's a cliche, but we need to treat each day as a gift. I'm going to miss him. |
Re: 57 Chevy Wagon - Californa Dreamin'
3 Attachment(s)
Here are some photos of the finished panels installed. The matte clear I used was still too glossy to suit me, so I used a 2000 grit foam backed pad to knock them down a bit more.
|
Re: 57 Chevy Wagon - Californa Dreamin'
Quote:
|
Re: 57 Chevy Wagon - Californa Dreamin'
Panels look great Vic. Condolences to all BOPPA's family and friends.
|
Re: 57 Chevy Wagon - Californa Dreamin'
Quote:
|
Re: 57 Chevy Wagon - Californa Dreamin'
1 Attachment(s)
Quote:
|
Re: 57 Chevy Wagon - Californa Dreamin'
Right on, I'll give you a call this week.
|
Re: 57 Chevy Wagon - Californa Dreamin'
what about louvers in the hood?
|
Re: 57 Chevy Wagon - Californa Dreamin'
Quote:
|
Re: 57 Chevy Wagon - Californa Dreamin'
5 Attachment(s)
It's been a little over five months since my last post. Lots of water under the bridge since then. World of Wheels went off without a hitch and the wagon looked great in the booth with Hot Rod Express. We picked up an ISCA award for Outstanding Interior - Custom which was nice. Car has been parked ever since except for the other day when Kathy had a flat tire and I used it to transport the air bubble to the store where she was parked.
We have acquired two new "project" cars. One is a '65 Ford Fairlane we picked up in Fond du Lac, WI. The other is an '87 Buick Grand National. I hadn't planned on the Buick, but one of my oldest buddies called to ask if I would buy it from him. He's in very poor health and was diagnosed with dementia a few years ago. He remembers all the stuff we did together back in the 60's and 70's but can't recall what the doctors told him even a few hours ago. Anyway, we hauled an open trailer down to AL and picked it up along with the numbers matching engine that was originally in it. Also loaded up several boxes full of spare parts. He's still finding parts he squirreled away, and I received a big box full of stuff just today. I'm pretty much out of space, so I'm contemplating running the wagon thru the Mecum auction at Dallas in September. Meanwhile, I'm tending to some much-needed repairs on the Buick. Feels good to get up in the morning and head down to the workshop with a cup of coffee in hand and a punch list to work on. I plan to do a build thread on the Fairlane once I get lined out. I'll keep you posted. |
Re: 57 Chevy Wagon - Californa Dreamin'
Quote:
I hate to see the wagon go. But I do like the new projects! |
Re: 57 Chevy Wagon - Californa Dreamin'
Quote:
|
Re: 57 Chevy Wagon - Californa Dreamin'
Quote:
|
Re: 57 Chevy Wagon - Californa Dreamin'
Just saw an article on fords new E crate motor, same setup as the E mustang. right now they’re no support directly from ford but will be coming soon. Ford did an F100 with the E mustang running gear got me thinking it probably won’t be long before we start seeing these E motors in older trucks and cars
There already putting running gear from recked Teslas in Porsches and other sport cars. I got to thinking about your new ford project. |
Re: 57 Chevy Wagon - Californa Dreamin'
Quote:
|
All times are GMT -4. The time now is 10:12 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com