Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
Hey, whats up Austin. Whats your truck plans this weekend? Im heading to Sanford tomorrow to meet up with Sharps40 and to grab a driveshaft and some parts I left on the last run. Going to finish dropping the crossmember and get prepped/painted this weekend. Time to break in the new compressor.
|
Re: 1963 C-10 in NC
4 Attachment(s)
On top of all the yard work and moving 16' logs around for the barn, I did manage to get the crossmember dropped. Got it loaded up and took it to advance auto to borrow their ball joint press. Ball joint came out with a little muscle, but no issues. Took it back home for degrease and pressure washing. Degreaser did ok for light stuff, but ultimately I ended up going to the dollar store for some over cleaner with sodium hydroxide....this did the trick nicely. Got the top done before I ran out of steam and light, so I'll finish up the bottom side tonight and maybe paint Tuesday if I get home at a decent time. Heres a few pics, its cleaning up very nice so far. Another step closer!!
The front end of the trailer project made a nice work station. I'll get new grade 8 bolts for the reinstall. All the original hardware came out with no issues, but there is some wear on the lower bolts due to location and being covered in road debris. |
Re: 1963 C-10 in NC
Looking good! I plan on doing this in a couple of weeks when I take vacation. Oven cleaner hugh. Thanks for the tip. I was wondering if sandblasting is going to clean through all the buildup.
Bret |
Re: 1963 C-10 in NC
2 Attachment(s)
I used some degreaser, which helped with the real light stuff. But the over cleaner and about 30 minutes of soak time really cut through the crud. I sprayed a whole can on the top and will use a whole can on the bottom aslo. Make sure you read the back of the can to make sure it has the sodium hydroxide...not all of them do. I used a wire brush and a flat tip screwdriver for the hard to get areas...maybe an hours work total on the top end. The bottom is much cleaner, will probably take another 30 minutes to do that. And there was some thick crud on it. I'd try the over cleaner 1st and see how it cleans it up for you. With the upper control arms off, the crossmember was easy to move around by myself.
Heres a before and after pic....hard to see all the crud and grease, road tar...etc...but its there. |
Re: 1963 C-10 in NC
3 Attachment(s)
Got the underside of the front crossmember done last night, so maybe I'll get some color on today after work. The oven cleaner did the job again. Best $4 I've spent this week.
|
Re: 1963 C-10 in NC
Going to stop by the store today and get some and a wire wheel. Going to start on my front end today. Last of the good weather this week so I want go get as much done as possible
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
Good morning, Looks like its time for a pancake?....and maybe some eggs.
|
Re: 1963 C-10 in NC
No, not dropping it, so the stock crossmember will work fine.
|
Re: 1963 C-10 in NC
3 Attachment(s)
Got 2 good coats of rust treet down. It converts any rust I may have missed, removes any grease I may have missed, etches the metal and provides a great surface for paint. Calling for rain all day today and lowered temps the next two days, so will probably be this weekend before it sees any paint.
The rust treet is an industrial strength chemical that I have used at work before and I've used it on quite a few truck projects with great results. Nice thing is it can be sprayed, brushed, or dipped on. Just let it dry thouroughly and your ready for paint. I normally apply two coats and it lays down very smooth. |
Re: 1963 C-10 in NC
Man that's lookin good! Keep up the good work! :chevy:
|
Re: 1963 C-10 in NC
5 Attachment(s)
Thanks TJ.
We had a bad rain/wind storm come through yesterday, but I had a few hours in between to get some paint laid down. The 30+ mph winds helped with a nice breeze to dry the paint. Will finish the paint this weekend. I want 1 more good coat down, but so far its looking real good. |
Re: 1963 C-10 in NC
Looks good man! Thanks for the motivation I hope to get the front half of my frame sandblasted today if the wind will cooperate.
Bret |
Re: 1963 C-10 in NC
Thanks Bret....slowly but surely its getting there.
I try and spend 30-60min a day at a minimum when weather and work permits. You'd be surprised how much can get done in little increments. |
Re: 1963 C-10 in NC
I second that. My problem is mine is about 10 minutes away at my MIL's so its not as convenient. But I try to bring things home I can work on after work. I'm off work on Thursday and Sundays and you pretty much know where I will be :)
Bret |
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
Indoors is great. Especially if you can fit a Fullsize pickup.
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
after hr's of cleaning and prep, then paint, that makes it all worth it. looking good!
|
Re: 1963 C-10 in NC
Quote:
Picked up new grade 8 bolts today for the reinstall. All the bolts were 7/16" x 1 1/2" coarse (14 bolts total) for the crossmember to frame bolts in case it helps anyone else in the future. My local shop charged me $7 total, money well spent in my opinion. |
Re: 1963 C-10 in NC
I go to ACE which is close to me, and grade 8 bolts aren't cheap. but 12mi to town make's it worth it.
|
Re: 1963 C-10 in NC
Quote:
The bolts I removed from the crossmember still looked good, but I figure it'll be quite some time if ever that I remove it again, so I figured new bolts was the way to go. I always use either grade 8 or stainless steel depending on the project. |
Re: 1963 C-10 in NC
Man that looks good! Really inspiring me to do mine! :metal:
|
Re: 1963 C-10 in NC
not that bad of a job tj. the hardest part is just making the decision to start doing it. my problem is once im ready to install in the next few weeks, new engine/trans and new front end will go on. so alot of different projects will come to a head at once
|
Re: 1963 C-10 in NC
Get all the little stuff lined up 1st TJ, new bolts, parts, paint, cleaners, tools... etc....the little stuff will nickel and dime you to death and its much easier to do the reinstall with all parts on hand.
Only part I'll have to rent is the ball joint press. I've never dropped the $ for one as its one of those things I use every 10 years and its easier to just get from Advanced Auto on loan. They require a refundable deposit, but no actual cost. |
Re: 1963 C-10 in NC
Last of the front suspension parts in. Moog Pitman Arm K6086 and Moog Idler Arm K14. Have to mark off the 600 yd range we're installing at Dad's Saturday and rain all day Sunday....maybe next week we'll get some parts installed.
|
Re: 1963 C-10 in NC
Hardest part of pressin in the new ball joints is gettin em lined up dead straight. Moog lower ball joints have a long taper to help but still hard to get dead straight. The less expensive/off shore lower balljoints have about 0 lead in taper and are a bear to get straight started, do it wrong and they will actually gouge the lip inside the lower control arm then stick crooked part way in.....
Recommend using a hand wrench and socket to turn the shaft on the press....air wrench can get ya in trouble quick if it ain't all lined up straight and true. Start em crooked and you have two issues, can't seat it and if you try too hard, it stretches out the hole and you wind up with a loose balljoint that has to be welded in place. In any event, I recommend tack welds on the bottom ball joint unless its a spanky new lower control arm yer pressin the joint into. |
Re: 1963 C-10 in NC
Ok, thanks Rich. We'll the A-Arms are new to me, but obviously 50+ years old....guess that doesn't count. HAHA. Will watch install for proper alignment and fit. Keep you posted with pics. The crossmember from ol John Lee cleaned up pretty good huh?
|
Re: 1963 C-10 in NC
Looks dayum fine. Make sure you measure and critically compare the DS upper control arm bracket to the PS and to your unstruck spare vehicles.
The DS of Ol John Lee was the hit that caved in and cracked the DS frame. Any doubts, cut the rivets and swap out your upper bracket from the DS side for one of the unstruck DS brackets off one of the spare vehicles. |
Re: 1963 C-10 in NC
I've checked and double checked everything and it all looks to be ok. I can't find any issues. Both uppers and lower arms move freely. All bolts came out good, none bent, even the ones that are welded to the crossmember (upper 2 bolts on the sides that hold the upper cross shafts) backed out just fine. Can't find any bends, buckles or cracks. I think its good to go. Seems to just have been the frame issues. But I have two other crossmembers (both 63) should I run into any issues.
|
Re: 1963 C-10 in NC
I think yer gonna be fine....weakest part of the front end is the frame. Had the frame been boxed or crossbraced I spect there would be more damage to attached components.
|
Re: 1963 C-10 in NC
We'll know more when we get to install, but I don't see any issues. Won't be long and I'll have that old big block stuffed down on top of it. Can't wait!!!!! Been a few years in the making.
And thanks for having drilled out the upper ball joints...glad I didn't have to mess with those rivots. And looks like the lower control arms were converted to the larger u-bolts. |
Re: 1963 C-10 in NC
Once the bigblock is installed you'll be smoking mustangs! :lol:
|
Re: 1963 C-10 in NC
Yep yer welcome. When I did that suspension on Ol John Lee, I did it up good....everythin new and heavy duty spanky new ubolts and then Wammo El Blammo Del Smasho Con Crunch-O only 6 weeks later!
|
Re: 1963 C-10 in NC
Quote:
|
Re: 1963 C-10 in NC
Hahahaha....thanks guys. This forum is always good for an early Monday morning laugh. I did get the upper a-arms prep and paint done this weekend. Also got the brand new spring stripped and will get them painted up sometime this week. Been nothing but rain since Saturday night and the temp dropped back into the 40-50's. It's suppose to pick up this weekend some, so more paint then.
All parts ready for front end reinstall....just waiting on the new Moog idler & pitman arm to arrive and it'll finally be install time. Engine and trans will be very close behind. |
Re: 1963 C-10 in NC
I would have had my whole front end painted if it was nice out... now its just a waiting game.
|
Re: 1963 C-10 in NC
Quote:
And let me tell you.....removing paint from coil springs had to have been the worst project ever. What a pain in the rear. Springs look great, but the manufacturer did the worse job ever on the paint. It just flaked off in sheets. What paint did adhere must have been held on with elephants snot. Couple of coats of paint stripper even had a tough time with it. Got 90% of paint removed and put a good heavy coat of oven cleaner on overnight. I'll check their status tonight when home. Thinking I'll paint them the same color as the engine. |
All times are GMT -4. The time now is 06:02 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com