Re: What did you do to your truck today?
 

Got rid of my old 16.5 wheels and got some more common 16's thinking it looks funny, satin black should help
Posted via Mobile Device

Re: What did you do to your truck today?
 

Got tired of the terrible lighting. Swapped out the incandescent sealed beams for some Ecode H4 lenses. These ones I fitted also have city lights built in. Think it makes it look super classy!

https://sphotos-a.xx.fbcdn.net/hphot...65675558_n.jpg

Re: What did you do to your truck today?
 

Completely disassembled and cut the frame for the Z notch!
Posted via Mobile Device

Re: What did you do to your truck today?
 

Posted via Mobile Device
Posted via Mobile Device

Re: What did you do to your truck today?
 

Changed out the old radiator and put in a new 3 row Alum. Radiator

http://i1019.photobucket.com/albums/...0/null-4-2.jpg

http://i1019.photobucket.com/albums/...0/null-5-2.jpg

http://i1019.photobucket.com/albums/...C10/null-8.jpg

http://i1019.photobucket.com/albums/...10/null-11.jpg


Did manage to break the fan shroud which was kind of brittle.

Re: What did you do to your truck today?
 

Emblems and mouldings aligned and mocked up...interestingly, I welded up more than 110 holes (some 2 in. in dis.) in the firewall, floor and various areas in the cab drilled by the previous owner. I had to drill 88 holes for the mouldings and emblems.

http://i268.photobucket.com/albums/j...ps71db6f60.jpg

http://i268.photobucket.com/albums/j...ps87145577.jpg

Re: What did you do to your truck today?
 

https://sphotos-a.xx.fbcdn.net/hphot...79631846_n.jpg
PUT A NEW WHEEL IN

Re: What did you do to your truck today?
 

I finally got to work on the tailgate today. I was going to have it blasted and then do the work but decided I have spent too much on the truck this year so I took a wire wheel to it with a drill. Turned out good. ground all the rust off then two heavy coats of rust inhibitor-treatment. I'll finish the coating later if it doesn't rain.

Re: What did you do to your truck today?
 

That turned out nice. What a lot of work. I hate sanding and stripping more than just about anything else, but sometimes it just has to be done the hard way.

Re: What did you do to your truck today?
 

Picked up my new edelbrock carb today and also painted my alternator bracket.

Re: What did you do to your truck today?
 

man, you look pretty young to be working on these trucks LOL

Re: What did you do to your truck today?
 

DID SOME EXHAUST WORK..... installed headers and mufflers,will and some more pipe later down the, have it end under the bed
https://fbcdn-sphotos-e-a.akamaihd.n...77862974_n.jpg
https://fbcdn-sphotos-g-a.akamaihd.n...74550526_n.jpg
https://fbcdn-sphotos-a-a.akamaihd.n...14110579_n.jpg
https://fbcdn-sphotos-d-a.akamaihd.n...54948279_n.jpg
https://sphotos-b.xx.fbcdn.net/hphot...28337261_n.jpg
https://sphotos-b.xx.fbcdn.net/hphot...73854022_n.jpg
https://sphotos-a.xx.fbcdn.net/hphot...70346718_n.jpg

Re: What did you do to your truck today?
 

I agree sanding and stripping is a real chore. I am in the process of taking my whole truck down to bare metal. It had been painted 5 times over the years counting the original and I didn't think it needed number 6.
Posted via Mobile Device

Re: What did you do to your truck today?
 

Hey.....gotta start somewhere.

That is my son. He is 11 but loves trucks and esp driving. :metal:

Re: What did you do to your truck today?
 

Grey primed the front fenders.

Re: What did you do to your truck today?
 

I have the same radiator and works awesome.

http://i1280.photobucket.com/albums/...ps81b740d9.jpg
http://i1280.photobucket.com/albums/...ps077f04ca.jpg
Posted via Mobile Device
Posted via Mobile Device

Re: What did you do to your truck today?
 

Installed the rear 4" springs today and the 7 blade fan. Also got to follow a new '14 in town. Good looking truck!

Chris

http://www.fquick.com/images/vehicle...5168373051.jpg

http://www.fquick.com/images/vehicle...5168373050.jpg
Posted via Mobile Device

Re: What did you do to your truck today?
 

Mounted up a set of 235 75 15 WWs on a set of correct wheels, and managed to press the yoke off my rear driveshaft! A good day. Pics tomorrow.

Re: What did you do to your truck today?
 

Posted via Mobile Device
Beginning of z notch
Posted via Mobile Device

Re: What did you do to your truck today?
 

finished fabing up some trans mounts and sent of the first half of a two piece drive shaft to be made. the trans mounts look horrible and will make better ones later as i'm still learning this whole welding/metal working thing but in the words of someone famous,

"...that'll do pig..."

Re: What did you do to your truck today?
 

Can you guys tell me where you got the aluminum radiators and what they cost? I have a 65 that needs a new one.
Posted via Mobile Device

Re: What did you do to your truck today?
 

Got mine on Ebay (Champion brand, iirc), and they cost about $175--again, iirc. Mine has worked great for 3 years or so. Our garage has ordered/installed several for other ap's and they have served well too.
Hth,
Sam

Re: What did you do to your truck today?
 

Got mine off eBay also.
Posted via Mobile Device

Re: What did you do to your truck today?
 

Went out for a late night gas fill up and just as we turned into the rather congested gas station, a 58-60 F100 was pulling out of the driveway. We spotted each other at the same time, exchanged waves and he gave a shot on his ahooga horn. At first I thought I was looking at my doppelganger! His truck was a black or dark burgundy stepside, had a full set of 5 spoke mags, and the beam axle was up in the front. I wish we had arrived a few minutes earlier so I could have gotten a better look. The whole encounter only lasted a second or two.

Ironically earlier in the day I spotted another 58-60 F100 two streets over. It was a gloss black shortbed fleetside. It had custom wheels, was lowered and very clean. Had I been driving the truck at the time I would have stopped and talked a bit. Just kind of funny to see two very similar trucks on the same day when I haven’t seen any nice examples like these in several years.

Re: What did you do to your truck today?
 

Spent an 1.5 hours putting in new halogens lamps - why 1.5 hours you ask to put in 4 headlights?

The outside low beams lights dropped in perfect and fit like a glove. The inside high beams however had factory tack welded "fitting tab" that did not line up with the hole in the buckets, these keep the bulb from rotating or vibrating. I had to haul out the dremel tool and find a cut-off wheel to remove some of the fitting tabs.

I then mounted the new heavy duty headlight hardness to the back side of the barbell. got all proud of myself and then realized I have to flip it as the red leads to the battery are on the wrong side. The mistake is a simple one to make. The wiring harness comes in from the drivers side from the factory, but the new harness needs to be hooked directly to the battery for power.

The white pipe cleaners "wire ties" are only temp. I could not find the pack of wire ties I have. I've probably moved them 3 to 4 times over the past year - now I can't fins them - go figure, Just as well as I would have had to cut the off anyway - small favor.

Re: What did you do to your truck today?
 

Looks great Jake.

Re: What did you do to your truck today?
 

Mark

I ordered the heavy duty harness from LMC for $29.99

36-3580 HEAVY-DUTY HEADLIGHT HARNESS

Remember to lay it our so the red leads are on the battery side.

Re: What did you do to your truck today?
 

Yeah it took a couple of hours just for the inside of the tailgate. It looks so much better now. When I do the outside I'm going to paint it. I have never painted anything before so we'll see how it turns out. I'm going with flat sublime green for the whole truck but just doing the tailgate myself.

Re: What did you do to your truck today?
 

Sanded last night, primed this morning and painted the white cab/stripes today. I finally broke down and took the fenders and grille support off so i can do those separately, and put a new grille support panel in as someone had done some bondo work on the nose, and it looks a little rough and i just don't want to spend a week working on it just to find out it doesn't look right anyways.

Re: What did you do to your truck today?
 

Painted and installed my rear bumper.

http://img.photobucket.com/albums/v3...s0684f842.jpeg

Re: What did you do to your truck today?
 

Had a great early Fathers Day present, I was able to get both of the boys over at the same time to help with the fenders and hood.

Not a bad days work, even at 93 degrees! Still need to tweak the upper howl cowls and screw down the wiper transmission cover, but DAMN I finally got the front assembled!!!:metal::ennyd::gmc:

Re: What did you do to your truck today?
 

Mark, here is where I mounted my relays for the new harness. I wanted to be able to unsnap them with out a lot of work. they get covered by the rad support cover

Re: What did you do to your truck today?
 

Jake I like that color blue it goes well with the white, won't be long and you will be driving it around. Although long time coming some things are worth the wait, and no one deserves it more than you..Vernski:metal::sumo:

Re: What did you do to your truck today?
 

Well since I did not get done tell late last night I am going to put down what I did yesterday. Work on my old 64 and got it running. Put the new intake and exhaust on my 66 also. Boy! Working on two trucks is tiring! But it was a great day all the same. Love the sound of straight pipes! Don't you?

Re: What did you do to your truck today?
 

Your truck is really turning out beautifully. When you first brought it home, did you ever envision it would take this long and the amount of work it’s taken to see it finished? And – with the years of effort and investment in it, will you be able to find the courage to actually drive it?!! ;)

Re: What did you do to your truck today?
 

Yep I sure do! Almost as much as I enjoy a 4 barrel dual exhaust inline 6. Nice work.

Re: What did you do to your truck today?
 

And – with the years of effort and investment in it, will you be able to find the courage to actually drive it?!! ;)[/QUOTE]

Several times I'd given up all hope, but glad to have stuck with it!

Re: What did you do to your truck today?
 

Mounted the bumper, I need to order two more bolts (or find the ones I had!) and the first lens. I need to figure out how to make the other lens get riveted or mounted to the housing without breaking it. It is WAY too rare to gamble with. The OEM factory ones I have plain mushroom head rivet, not the traditional type, where you pull the shaft though. I think they are airplane style, if so I have a friend who just built his own aircraft who has all the tools

Re: What did you do to your truck today?
 

Got some paint slapped on her! It's far from good, but good from far!

Re: What did you do to your truck today?
 

Great day with the boys it looks like. Your truck is looking great.