Re: Another turbo ls
I gather that the new differential is a Moser Dana 60?
|
Re: Another turbo ls
https://photos.app.goo.gl/suN7jsh4uRJqrdzN8
This turd is getting a turbo in the next month or so if I can find the time. Neighbor down the street has a 66 c10, I never looked twice at them till I was around his, Now i might like them more than 67-72s. Looking good man, keep up the good work, let me know how that moser works out. |
Re: Another turbo ls
Quote:
|
Re: Another turbo ls
Good Job! But I wish you would clean up that nasty ass engine!
|
Re: Another turbo ls
This is my 31x12x3 intercooler - sliced the vertical parts of the rad supports to fit the ends, but it will fit behind an un-cut '61 grill.
https://www.gwellwood.com/wordpress/..._n-672x378.jpg |
Re: Another turbo ls
Looking good.
|
Re: Another turbo ls
2 Attachment(s)
Between moving and life this was put on hold but I've finally got to give it some attention mostly part gathering but I did cut some plates for the TRZ anti roll bar
Attachment 2143483 Attachment 2143484 |
Re: Another turbo ls
2 Attachment(s)
Attachment 2152369
Attachment 2152370 I had a little time today to start mocking up the new FSP log manifold and 4" down pipe. Kinda glad things are going slow, this is a much nicer setup. |
Re: Another turbo ls
Looks like it's going to be a runner. Nice so far.
|
Re: Another turbo ls
3 Attachment(s)
I was able to get my Aldan coil overs mocked up today :metal:
Attachment 2152989 Attachment 2152990 Attachment 2152991 |
Re: Another turbo ls
Nice progress!
|
Re: Another turbo ls
I do not have turbo on my LS but i do have the Holly Wire system. All in except for a few hard wires. From what i have heard it is a great system.
|
Re: Another turbo ls
What rear end cover is that?
https://67-72chevytrucks.com/vboard/...0&d=1640039170 |
Re: Another turbo ls
Dana 60
|
Re: Another turbo ls
Yeah that's the Moser version of a Dana 60
|
Re: Another turbo ls
5 Attachment(s)
I gotta around to doing the coilovers on the front end this week
Attachment 2158222 Attachment 2158223 Attachment 2158224 Attachment 2158225 Attachment 2158226 |
Re: Another turbo ls
Nice! Who's front coiler over kit did you use?
|
Re: Another turbo ls
I'd like to see a 3/16" or 1/4" thick ring at the bottom of the old spring pocket to spread the load of the coilover mount over such thin sheet metal.
|
Re: Another turbo ls
Quote:
|
Re: Another turbo ls
Quote:
|
Re: Another turbo ls
Absolutely.
But also..... for how long? You don't have to do any of it, but from an engineering standpoint, that's a lot of point load on a relatively small surface area. |
Re: Another turbo ls
Quote:
That pic doesn't show good enough but mount on the coil over is actually wider then the flat surface of the control arm therefore distributing the weight across the old spring pocket |
Re: Another turbo ls
2 Attachment(s)
Got some more of the exhaust mocked up, now I'm debating where to put the electric cut out...
Attachment 2164867 Attachment 2164866 |
Re: Another turbo ls
2 Attachment(s)
|
Re: Another turbo ls
2 Attachment(s)
Attachment 2183047
Attachment 2183048 I was able to get a bit done last weekend, got the old trailing arm cross member out and the POL one in and the Moser trailing arms installed |
All times are GMT -4. The time now is 10:21 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com