Re: Billet Aluminum Dash Panels and Glove Box Doors
 

NO! Too hard to hold down and machine the outside. I use the gauge holes to clamp the piece down to the table.

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

How about if you made a hole in the center to clamp it down? I will eventually be cutting out a lot of the center. I want to install a 2005 cluster in my Jimmy someday to go with the 2005 engine I am installing. I will want to cut out the center to frame that cluster? I am in no rush either I could wait until you do another batch?

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

No?

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

I cannot justify doing one or two solid panels with all the mods I have to make to the program and the tooling without making the price significantly higher. And from past experience, most people won't pay the extra money.

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

When is this deal over? I am in Cali so what is the total?

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

I thought it would be less work? I would have waited until you did another run? Oh well thanks anyway

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

are these still avail? and can you do 3 3/8 for tach and speedo?

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

Looks sweet- adding to my wishlist;)

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

use toe clamps & double sided tape on it ... stop the machine as you approach the clamps using an optional stop or a feed hold ... remove clamp ... cut ... replace clamp

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

The deal is over when they are gone. I have eight sets left.

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

Payment sent.

Last posted was eight left?

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

I will have it sent out today. Thanks for the business.

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

Bump for a SCHWEET deal.

Just got mine last week!

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

Can I get one made with no head light and wiper hole in it? Also would it be possable to get it made with two 5" holes and five 2 5/8", one 2 5/8" hole being in the center and the other four at the bottom? If you can do it like that what would the price be just for the Dash? Thanks

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

I looked into it and they won't fit on the dash panel. Not enough room.

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

I have them set up for that but I would need to get a run of at least ten to make it worth while to run on the machine. I am just trying to clear out my inventory.

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

Thanks for looking into it. If you can't do the 2 5/8 than can I get one made with two 5" holes and five 2 1/16 holes with out the wiper and light holes? If you can do it how much will it cost?
Thanks

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

any left? email me at kenmc@mts.net with payment info and I will reply with shipping adress etc. Thanks

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

im interested if you let me know what you have left.

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

PM sent and Yes I still have some left.

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

I need one with 2- 5" and 5 2 1/16" are these still available?

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

I need the same thing as above but with no wiper and head light holes can you do this?

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

how much for a glove box door shipped to 95991 (CA btw)

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

Do you have any available with just the 2 - 5" holes, and of course the wiper and headlight holes too?

Re: Billet Aluminum Dash Panels and Glove Box Doors
 

Just need a glove box door. price shipped to 96007?