The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   LSx Swaps (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=206)
-   -   LS swappers, post up your pics!! (https://67-72chevytrucks.com/vboard/showthread.php?t=412159)

eagleuh1 08-22-2010 09:12 PM

More of the same.
http://i894.photobucket.com/albums/a...m/IMG_0545.jpg
http://i894.photobucket.com/albums/a...m/IMG_0543.jpg
http://i894.photobucket.com/albums/a...m/IMG_0516.jpg
http://i894.photobucket.com/albums/a...m/IMG_0515.jpg
Let me know if you need more or an actual measurement for something. Good luck.

I did need to massage the seem lip in the tranny tunnel to get more clearance for the vent tube on top of tranny, to avoid rubbing noises later.

I like where mine sets. Plenty of room up front. Room behind. Not touching firewall etc. I did have to drill rivets out to move tranny crossmember forward, I think about 2 inches. The oil pan( truck pan) clears the front crossmember with at least a 1/4 inch or more. It hangs below frame though. Mines c20 at stock height, so who cares. Skid pan to come later though. The only problems I had with going this far back were the seem on tunnel needed folded back a little, the Lokar cable for shifter to me is a little short, tight bends. And my Doug Thorley headers dumped right in front of Parking brake cables, so it was tight bends coming out to exhaust. I thank my exhaust man for doing such a good job at that fix. Drive shaft needed shortened, but that fixed my vibration problems. Found out shaft yoke wasn't welded on square from factory I guess. Any questions just ask. Good luck. I'll take some pics of the plates I made for the motor mounts tommorrow.

trenz68 08-30-2010 05:25 AM

Re: LS swappers, post up your pics!!
 
1 Attachment(s)
heres mine

Shon 08-30-2010 02:43 PM

Re: LS swappers, post up your pics!!
 
...

Hart_Rod 08-31-2010 06:37 AM

Re: LS swappers, post up your pics!!
 
3 Attachment(s)
Mine....

menace121978 09-14-2010 08:03 PM

Re: LS swappers, post up your pics!!
 
1 Attachment(s)
here's a some what current one...

menace121978 09-15-2010 04:09 PM

Re: LS swappers, post up your pics!!
 
The rims are eagle alloy 225's with toyp proxy II.

That is a factory 3 piece escalade covers that have been smoothed by driveway dreams(Gerald) and painted:D

thanks for the compliments guys;):metal:

LEEVON 09-19-2010 11:49 PM

Re: LS swappers, post up your pics!!
 
In progress. The block will be blue like the wheels and it will have cast aluminum finned valve covers. That is an NP833 o/d 4-speed behind it. Just finished putting in a 212/218 .522/.529 cam, LS6 springs, and TSP pushrods. Gonna need some less expensive tires for burnouts...
http://farm5.static.flickr.com/4124/...1433013b_b.jpg

glock35ipsc 09-20-2010 03:55 PM

Re: LS swappers, post up your pics!!
 
2 Attachment(s)
low_84_inchaska - I built a simple box mount for mine that sets up against the rad support, and uses two of the three rad support-to-inner fender mounting holes.

It's since been painted. :D

shaunatk 09-27-2010 01:16 PM

Re: LS swappers, post up your pics!!
 
5.3L and mockup transmission are finally mounted!

Here's the mounts we created. The chassis is 2003 S10, and the engine sits back about 8.5":

http://img291.imageshack.us/img291/8729/mountg.jpg
http://img153.imageshack.us/img153/4959/mount2.jpg
http://img227.imageshack.us/img227/9727/mount3k.jpg

What it looks like when attached to the frame (using all existing threaded holes and stock S10 motor mounts)

http://img405.imageshack.us/img405/2328/mount4.jpg

Finally!

http://img825.imageshack.us/img825/5214/mount5.jpg

I have a re-worked harness, LS1 intake, fuel rails, injectors, and idler pulley relocation bracket. I have an un-tuned PCM. I bought a F-body oil pan and dipstick tube. I bought F-body manifolds (which aren't going to work either).

I still need all of the truck accessories and brackets. Also still need a starter. Also, I still need to cross my fingers, and hope that when we swap oil pans and check the bearings that everything looks ok. I still need an electric fan. I still need a 4L60E transmission (have a lead on one for $50, but needs rebuilt, will probably purchase soon). I assume that I'm going to need a MAF. Also need an air intake tube and filter.

This swap will nickle and dime you to death. Don't go into the swap thinking you're going to spend less than $1500. It's just not going to happen.

If anybody switched to a F-body or Vette accessory system, and still has the truck accessory drive that they want to sell, please send me a PM.

It's going to suck forking out the money for custom headers, but we don't see any way around it. We may try to make our own though...

Our next step is mounting the S10 steering column.

Wasted Income 09-28-2010 06:03 PM

Re: LS swappers, post up your pics!!
 
5.3L / 72 mm turbo / head studs / rod bolts / LS6 cam / 4L80E and Yank 3400

http://sphotos.ak.fbcdn.net/photos-a...15637_9251.jpg

http://sphotos.ak.fbcdn.net/photos-a...15635_8782.jpg

http://hphotos-snc3.fbcdn.net/hs039...._6475557_n.jpg

85burb 10-24-2010 05:05 PM

Re: LS swappers, post up your pics!!
 
2 Attachment(s)
Here is my LQ4 that will be going in my 85 4X4 burb. Has F body headers and SDPC Hot Truck Series HT1 cam 214/218 555/562lift and 111 LSA. Streat avenger 670 cfm carb and edelbrock duel plain intake. Awaiting fianl clean and assembly and paint.:metal:

mrhino 10-24-2010 07:27 PM

Re: LS swappers, post up your pics!!
 
Here's what I got. 01 5.3l, 4l60e classic Performance tubular engine mounts, Sanderson headers.

http://i571.photobucket.com/albums/s...r/DSCF3582.jpg
http://i571.photobucket.com/albums/s...r/DSCF3592.jpg
http://i571.photobucket.com/albums/s...r/DSCF4270.jpg

Check it out! I Just Started a Build thread

smokedat 11-03-2010 03:58 PM

Re: LS swappers, post up your pics!!
 
5 Attachment(s)
LS1 on K5 and LS1 on 74 C10

Oval55rag 11-06-2010 12:04 AM

Re: LS swappers, post up your pics!!
 

68GMCCustom 11-22-2010 02:10 PM

Re: LS swappers, post up your pics!!
 
mines getting close....

http://www.lsxtrucks.com/gallery/alb...l_IMG_1530.jpg

http://www.lsxtrucks.com/gallery/alb...l_IMG_1531.jpg

http://www.lsxtrucks.com/gallery/alb...l_IMG_1532.jpg

85burb 11-22-2010 09:19 PM

Re: LS swappers, post up your pics!!
 
2 Attachment(s)
Got motor mostly back together and only have few more things to order.....we have all said that befor....:lol:

67C10BUB 11-23-2010 06:59 AM

Re: LS swappers, post up your pics!!
 
3 Attachment(s)
Here's mine. 2008 Silverado 5.3L / 4L60E in a 67 C10.

85burb 11-26-2010 11:47 PM

Re: LS swappers, post up your pics!!
 
1 Attachment(s)
Got a few more things installed...

matthew20061 11-29-2010 05:19 AM

Re: LS swappers, post up your pics!!
 
My 1969 Chevy C-10 Stepside Swap, started off as a simple 5.3L swap with a nice electroic 4L60E. Then I decided that wasn't good enough so I cammed it, that was a great improvement but then I decided to go crazy and swap it out with a completely build up LQ9 6.0L with brand new high flowing L92 cylinder heads, LS3 Intake manifold, 90mm throttle body, Comp Cams 223/231, .610/.617, on 112 lsa. I topped the new motor off with GM Performance Part LSX polished valve covers and hiding the coils in the frame rails!!! :chevy:
PICS:
http://i989.photobucket.com/albums/a..._0436Small.jpg
http://i989.photobucket.com/albums/a..._0440Small.jpg
http://i989.photobucket.com/albums/a..._0442Small.jpg
http://i989.photobucket.com/albums/a...0451Medium.jpg
http://i989.photobucket.com/albums/a...0453Medium.jpg
http://i989.photobucket.com/albums/a...0454Medium.jpg
http://i989.photobucket.com/albums/a...0455Medium.jpg
http://i989.photobucket.com/albums/a...0456Medium.jpg
http://i989.photobucket.com/albums/a...0457Medium.jpg
http://i989.photobucket.com/albums/a...0458Medium.jpg

VIDEO:

Many more pics in my build thread and I'm planning on taking it out to the track this spring to see how fast it is! :devil:

matthew20061 11-29-2010 08:06 PM

Re: LS swappers, post up your pics!!
 
Quote:

Originally Posted by mac72 (Post 4320328)
Really nice job! Ive been wanting to see a pic of those valve covers,thanks for sharing. Do you have any hp&torq numbers with that cam & head combo?

I just got it running for the first time this week so no numbers from my exact setup but I copyed this setup: "LS2 with L92 Heads LS3 Manifold makes 460rwhp and 446rwtq" So it should run awesome!!! :chevy:

c.brown 12-06-2010 06:13 PM

Re: LS swappers, post up your pics!!
 
1 Attachment(s)
i finally explored this sight farther than the 60-66 section heres mine so far 1966 suburban 6.2 and a 6l90e porterbuilt front and rear

gopokes 12-07-2010 12:59 PM

Re: LS swappers, post up your pics!!
 
Doesn't look all that great yet, but had the first start up last night!! That's my brother that sounds like a crazy person laughing, he was a little excited. :lol:

http://i681.photobucket.com/albums/v...h_SANY0097.jpg

oldmanlance 01-04-2011 01:28 AM

Re: LS swappers, post up your pics!!
 
2 Attachment(s)
[attach]676327[Attachment 676328/attach]

oldmanlance 01-04-2011 01:38 AM

Re: LS swappers, post up your pics!!
 
2 Attachment(s)
[attach]676332[/attachAttachment 676333]

oldmanlance 01-04-2011 07:20 PM

Re: LS swappers, post up your pics!!
 
im using duel electric fans kit from old air products ,had it on the truck when i had the 402 in it.thought i would go alittle modern with the 5.3 ,4l6e


All times are GMT -4. The time now is 05:54 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com