Re: 64 C20 Barn Find Parting Out (new listing)
 

pictures are loaded below, taillight bezels were trash, housing are clean and the tail light lens survived. Only one emblem survived as well, Let me what you think.

Re: 64 C20 Barn Find Parting Out (new listing)
 

I'll be using the gas cap, Thanks

Re: 64 C20 Barn Find Parting Out (new listing)
 

I'm going to hang on the tire carrier. Thanks

Re: 64 C20 Barn Find Parting Out (new listing)
 

I don' think it survived, but haven't torn the cab apart yet.

Re: 64 C20 Barn Find Parting Out (new listing)
 

driver side is a replacement, pass side is the same as you have.

Re: 64 C20 Barn Find Parting Out (new listing)
 

grille pic loaded, no trim on this truck except for sail panels, haven't got to the heater assembly yet.

Re: 64 C20 Barn Find Parting Out (new listing)
 

The 8 lug rear end is coil springs and trailing arms. The grille support panel was in good shape, but I'm going to use it. I will post a picture and price of the rear end after I get the bed removed today.

Re: 64 C20 Barn Find Parting Out (new listing)
 

The sail panel trim is what I meant. Thanks, just let me know on a package deal with grill, headlite bezels, heater box under dash and sail panel trim

Re: 64 C20 Barn Find Parting Out (new listing)
 

You are using this cab, yes? Do you have another cab and how if the area above the windshield? I am looking for a piece on the drivers side just above the windshield if you have a cab you are going to scrap.

I will try to find a photo and post with the section I need highlighted.

Thank you

Re: 64 C20 Barn Find Parting Out (new listing)
 

I will take the drivers vent window if the handle is good and not loose and the upper radiator bracket.

Re: 64 C20 Barn Find Parting Out (new listing)
 

To take your bet about rust in the front. Here are more up close pics.

By the way: Rule XII. It is against our policy for someone to post a complaint about a members price on whatever they are selling. If you don't like the price then skip it. Let it drop to the bottom on its own. They (potential buyers) will figure it out, why nobody is jumping on that particular item.

Re: 64 C20 Barn Find Parting Out (new listing)
 

Another

Re: 64 C20 Barn Find Parting Out (new listing)
 

Last

Re: 64 C20 Barn Find Parting Out (new listing)
 

I do have another cab I'm going to scrap and are welcome to whatever you need. I see it looks like left upper corner. How big of piece would you like me to cut out? I will make sure that location is in good condition tomorrow.

Re: 64 C20 Barn Find Parting Out (new listing)
 

Thanks for letting me know.

Re: 64 C20 Barn Find Parting Out (new listing)
 

Cab is apart now and the floor mat didn't survive.

Re: 64 C20 Barn Find Parting Out (new listing)
 

Thanks for checking.

Re: 64 C20 Barn Find Parting Out (new listing)
 

$150.00 plus the ride or come pick it up.

Re: 64 C20 Barn Find Parting Out (new listing)
 

Here are some pics of the rear end. Let me know what on the rear end your interested in.

Re: 64 C20 Barn Find Parting Out (new listing)
 

Another.

Re: 64 C20 Barn Find Parting Out (new listing)
 

Bed rails only one hole is out of round, no rust. 20.00 a rail or 100.00 for the set. (SCRAPED)

Re: 64 C20 Barn Find Parting Out (new listing)
 

Wheels tubs no rust and square holes, but pretty dented up. Don't know if anyone needs them, but hate to scrap them since they aren't rusted out on the edges. 15.00 per plus ride. (SCRAPED)

Re: 64 C20 Barn Find Parting Out (new listing)
 

Front bed panel, not too bad. A few holes rusted out and has a little bow to it. 20.00 plus ride. (SCRAPED)

Re: 64 C20 Barn Find Parting Out (new listing)
 

Another

Re: 64 C20 Barn Find Parting Out (new listing)
 

Thank you,

Let me know what you have. I would say the cut should be about 2 to 3 inches on each side of the rot in my photo. I don't want it to big or it is a pain for you to ship.

By the way: The hood is one of the nicest ones that I have seen for the price. If it did not cost so much to ship, I would consider it. The droop in the middle is an easy repair. I know very well how hard it is to find one of these hoods that does not have front edge rot.

I appreciate your time, Thank you