Re: Suburban metal cuts
 

What is circled in red Richard....needing the last 3-4" of roof from drip rail flange to 1/2" above body line. Need around 40" of length.

Re: Suburban metal cuts
 

I really don't know why I am being so dense on this, I just keep looking at the pic you posted and it looks like you need the part i have the yellow arrow at. Or is that what you were trying to cut and went too high into the roof half?


.

Re: Suburban metal cuts
 

I think i am going to go lay down and revisit it in the morning.

Re: Suburban metal cuts
 

Hey Richard, this is what I am trying to fill in. This should explain I need the drip rail flange on the roof that gets spot welded to the drip railing. Then I am asking you to cut it just above the extra body line that a Burb roof has. I burnt through one of mine when I was trying to remove it.

Re: Suburban metal cuts
 

Josh
$75 shipped for both pcs

.

Re: Suburban metal cuts
 

Trevor,
I am understanding what you need. I will get it cut out later today. $25 plus shipping. Not sure if I still have your address but should be able to locate on PP

Richard

Re: Suburban metal cuts
 

Trevor
Here is what I cut out. I unbolted it from the lower half. The pc is just shy of 48" just bc it made no difference in the shipping cost from 40''. anything longer than 48'' and the cost almost doubled being over sized. If I did not cut it correctly I still have the entire driver side to try again lol. $55 shipped if it is correct. PP in my sig below

Thanks

.

Re: Suburban metal cuts
 

Perfect Richard, PayPal sent. Thanks again, Trevor

Re: Suburban metal cuts
 

Got it and it will ship in the morning as well. Thanks

Re: Suburban metal cuts
 

Thanks Richard, I got the piece yesterday. Looks great. Trevor

Re: Suburban metal cuts
 

Richard did you end up scrapping these out? Trevor

Re: Suburban metal cuts
 

I still have quite a bit

Re: Suburban metal cuts
 

Richard, I may be needing a 8-10” piece of inner pillar off a driver’s inner b pillar. I’ll let you know tomorrow.

Re: Suburban metal cuts
 

here is pics of what is left both have been cut pretty much flush at the front of them heading towards the A pillar

.

Re: Suburban metal cuts
 

Actually Richard, those are perfect for me. I am working on finishing my inner roof and need pieces to transition from the pillars to the I need roof as shown. Before I finish welding and grinding, I wanted to get a game plan.

Re: Suburban metal cuts
 

So you basically only need the inner metal overlay like I have boxed here, or do you need the entire thickness of it all the way to the outside roof?

DO you need any of the horizontal cover above the doors?

.

Re: Suburban metal cuts
 

Basically, that is all I need Richard. I do not need any of the pieces above the door. I already have my whole inner roof mocked up other than finishing it out and these pieces. If you can cut out both of those for me as I need two for each side. Maybe 3" inches below the door weatherstrip channel intersection but above the shoulder harness hole. Thanks Trevor

Re: Suburban metal cuts
 

Looking for drivers side rear frame section from axle crossmember to bumper. I need it for a Blazer. If you have one from Suburban hoping it might work.

Re: Suburban metal cuts
 

The tail end of the suburban is different from the 72' Blazers. Here are a couple pictures to show the difference. If your Blazer is 69-71 the frame just cuts off flat at the rear but I do not have one here to verify if they are indeed swapable.

1st picture shows suburban tail end

Attachment 1960934

2nd pic shows how the blazer turns down a lot sharper. This frame is not for sale. You might check with 1Rippen6 he usually has some blazer stuff

Attachment 1960935

Re: Suburban metal cuts
 

Thanks. With the turn down on Blazer not sure I could make the Suburban piece work.

Re: Suburban metal cuts
 

Hey Richard, these would work.

Re: Suburban metal cuts
 

are ya still parting these out? i need this section, its driver side back wheel arch area.. piece i used did not have the wheel arch indention.. :(

Re: Suburban metal cuts
 

Missed this with the holidays. I do not have ant good lower metal, everything is rusty or totally gone

Re: Suburban metal cuts
 

ok thanks for checkin!

Re: Suburban metal cuts
 

I see you said you don't have any good lower metal, what about the driver's rear wheel well? I need a small section at the front, 4" up and 3" toward the rear to include the corner.

Attachment 1973201

I can take a better picture with tape on the wheel well if it would communicate better. This is the area I'm trying to patch.

Attachment 1973203