Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

well if i was you i would just hunker down with some 10 cheapos.... until i had the cash to have someone make duplicites of the originals and recover each bench, starting with the front of course... you will be much happier and pleased with the out come.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

New grill trim installed then finished cleaning all the old sound deadener and crap off the floor with some acetone. Started installing carpet after fixing some floor rust issues last weekend, then located the two carpet hold down strips I picked up from Sharpie. Next week motor goes in and install the newly black powder coated 15X8 rims with 33' BFG AT tires.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

:jdp: man and to think if my dad didnt junk his 68 burb i would have one today!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

looks great!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Just found the link to your build thread. Looks like a great project. My suburban came out of Arizona also. I had to replace all the rubber since it had been cooked by the sun. But you can't beat the rust free sheet metal. Can you post the exact size and brand of the tires you are installing. I am also in the process of trying to determine what is the best size tire to put on my truck. Currently a 265/75/15 is as large as I can find for a tire that is not an off road type tire.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

33" X 10.5 X 15" BF Goodrich All Terrain's.
http://www.summitracing.com/parts/BFG-63540/

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

my dad has the same brand of tire and the same tread dont know if the size is the same or not though.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Some progress.....
Dash near complete, just need to install ashtray and paint column/wheel.
Disassembled rear seat and painted brackets they looked bad.
Ordered set of braided stainless brake lines to replace rubber lines front/rear. Installed new rear axle hard lines and rebuilt rear brakes with all new parts.
Front wheel cylinder rebuild kit's $5 at napa. They want's $65 each for new cylinders, guess odd ball wheel cylinders on 68 4X4's sure ain't cheap yikes!!!!!!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

I like this build! Subscribed!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

great progress! i know why you havent been on a lil while lol! you could do what the pcis show in a day but it takes a couple days to do it as nice as you have done.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Engine's in... then slowly wiggled transmission and transfer case into place.
Dam those are a beast to put in alone.... nothing like putting a starter in.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

its been to long chad! we definalty need pics and i havent done it but it sounds like a pain!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Sweet Burb build and great work on it so far! That paint work you have done is awesome!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Some shots of install of trans and engine.
Find a friend to help ya put the trans/transfer case in, lots of back and forth doing it alone.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

That looks great!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Nice job with the hoist from above. I've mounted a couple of manual transmissions by myself and it sure does take a lot of wiggling. I can't even begin to imagine the fun it must have been with that NP205 hanging off the back too.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Freshly powder coated 15X8 for the 33" BF Goodrich AT's back from the shop.
Time to get it on the road!!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

wow how did i miss that? want to come do my engine? rims look great! is that the actual paint for the transfer case? or are you going to get chrysler orange engine paint and paint it in original color?

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Took a while but..... finally, after 7 weeks it runs.
Bring on the snow!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Looking sharp!

The pictures of the trans/tcase going in gave me shivers, since I have done that on my burb twice by myself. But when I did the body off I put the trans/tcase, and the engine in all at once with a fork lift. :lol:
I was all proud of getting away with out having to do that by myself, but when the body went on and I started to connect everything. Guess what.. I forgot to put the clutch fork in when I had it all apart! :banghead: :lol: I can laugh about it now I guess.

I am saving up to do my bench seat overhauls (cushions and covers) on all 3 benches, which is huge money to do because of all the materials and labor for 3 benches.

I'd love it if you could take detailed pictures of your current benches, because that is the pattern I am going with but in the original lite green and black vinyl/fabric.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

I'm glad to hear some one is getting their projects running. :lol: Great job!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Chris,

I cut some of the material off the bench seats and am sending to SMS Auto fabrics in Canby Oregon for a quote. I'll make sure they know you are looking for the same material for your rig. I can also send you a small patch of the material. PM me you mailing address if you want a sample pc.

Yeah putting the Trans/Tcase in major pain in the ass, fork lift sounds much better! ;)

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Original 68 rear seat material pictures.
Looks like vectorit and I are going to both of our seat sets redone to original in the future. I will be bringing my seats in to SMS for stock seat cover templates for 67-68 burb's in original fabric.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

That's cool. Good luck with it man.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

wow that seat looks really nice!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Getting very close to some road time now that the snow's flying..... looks like right around 10 weeks from delivery to driving.
Rear portion of rear drive shaft getting shortened 5 1/2" since it originally had a rockwell T221 and now a NP205 Tcase. Used a piece of plywood to mimic carrier bearing mount location until I finish fabing one up out of 3/8" plate, it is no where near the original location, see link - http://67-72chevytrucks.com/vboard/s...d.php?t=282516

The front drive shaft length is perfect since was from a 69 with a NP205. BFG AT's getting mounted next weekend on the rims. Finish installing a few interior pc's new shocks and new exhaust and call it done till the spring. :)

Still have not put the 4" lift on I'm more interested in driving it for now, lift consist of.
http://www.sky-manufacturing.com/new...duct.php?id=98
http://www.jackit.com/skj-c240s-c.html
http://www.jackit.com/suspension-par...pcs-gdl40.html

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

lookin good!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

nice!:) keep it up. to bad about the driveline.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

I knew it had to be shortened, the NP205 is a bit longer and output shaft is on top not like the 221 is located the bottom of the transfer case.
No big deal, I had a bud who works at a driveline shop and does it for free for me.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

This project is coming together quickly and nicely! Good work Mt Man Chad!

Question for you…what did you paint the firewall and dash with? Spray gun, spray bomb, etc? It looks great.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

My favorite HVLP gun yet for ease of use and adjustment.
Binks - M1G http://www.binks.com/Products/SprayG...0/Default.aspx

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Figured you were using a nice spray gun. Binks are some of the best! Pricey though

I’m loving your Sub!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

It's moves under it's own power after 10 weeks.
installed shortened/balanced drive shaft and fits perfect with new carrier bearing mount. Used the string trick between front U joint and rear axle to place the carrier bearing on the money.
Traded a few truck parts for a nice set of 31" X 10.5's BFG's till the spring, then the 33's and the 4" lift goes on. Also the correct 68 style air cleaner assembly finally was caustic dipped I picked up from Sharpie, just need to paint it.

Only a few steps left till it's really road worthy.
Install new wind shield, new gas tank and finish up a couple misc items.
She ain't super pretty but..... it's sound driver mechanically from front to back.

Short video of startup after everything was installed.
http://www.youtube.com/user/mtnmanchad?feature=mhee

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Looking good, and congratulations on hitting a big milestone in your build!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Thanks Chris, long way to go before it's as nice as yours!!!!!!

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

oh :jdp: man i was checking this build daily for updates! glad it was good one! just subscribed to your channel. the burb is super nice very cool patina out side very nice redone interior on the inside! the rims tires... all of it you hit the nail on the head. are you going to get any hub caps for it??? maybe buy 68 1/2 on hub caps and cut the centers out of two, that have dented rusty messed up centers ,so its not a complete waste?

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

I love this truck, nice work your attention to detail is great it's like all these small things add up.
Posted via Mobile Device

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Picked up a very nice restored correct 7028213 on evilbay for the cost of what most are asking for unrestored carbs.

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

Dang! That looks nice.

Does the seller have more?

Re: Project "Daa BURB" - 1968 Chevy C10 4X4 Suburban
 

I'm looking and will keep you posted if I see any, just sent him a message if he has any more.
I'll send you the sellers name if you want to contact him, he has 100% positive feedback from hundreds of carbs.