![]() |
Re: 1960-1972 Lowering Block U bolts
64.95 shipped via priority mail 2-3 day shipping
Posted via Mobile Device |
Re: 1960-1972 Lowering Block U bolts
I as well would like a set of the 1" blocks and bolt kit. Can you tell me how much to 95242? Thank you.
Posted via Mobile Device |
Re: 1960-1972 Lowering Block U bolts
Posted via Mobile Device
|
Re: 1960-1972 Lowering Block U bolts
Sorry for the blank response. Blocks and bolts kit is 64.95 shipped
Posted via Mobile Device |
Re: 1960-1972 Lowering Block U bolts
Ok I would like to buy a set tonight. You take paypal?
Posted via Mobile Device |
Re: 1960-1972 Lowering Block U bolts
Bump
Posted via Mobile Device |
Re: 1960-1972 Lowering Block U bolts
Shawn,I sent you a PM
|
Re: 1960-1972 Lowering Block U bolts
Any group buy in the near future :chevy: or a discount for 2 or more sets (2" blocks with bolts and hardware)?
|
Re: 1960-1972 Lowering Block U bolts
Quote:
Thanks |
Re: 1960-1972 Lowering Block U bolts
I might be interested in something like that jonathon...let me keep watering my paypal tree a bit longer first :)
I cut my front springs and want my rear to come down a little but am afraid to run dropped springs because I wanna still use it like a truck |
Re: 1960-1972 Lowering Block U bolts
Ok I got my 1" blocks and ubolts today. Thank you Boris for the fast shipping. Now not to jack this thread but I went to install them today and I could not remove my old ubolts. They are rusted solid. I am working on a 68 swb and would love any suggestions on how to remove them. I am good with the torch and cut off wheel so if this is the way to go let me know where to start. Thank you in advance. Shawn
Posted via Mobile Device |
Re: 1960-1972 Lowering Block U bolts
Try to heat at the nuts first and see if they'll come off but if not, two cuts at the top of each (before they start curving over) and you'll be able to (hopefully) pound them out of the trailing arm but they'll be off the rear. I still had to heat mine on one truck to get them out of the trailing arms as they had siezed inside the trailing arms...
|
Re: 1960-1972 Lowering Block U bolts
I got the nuts off really easy. It's the ubolts themselves that are froze solid inside of the trailing arms. Where did you apply the heat to get them out?
Posted via Mobile Device |
Re: 1960-1972 Lowering Block U bolts
Boris... is it $5 shipping for two u-bolts? Looking at picking up a set of 1.5" u-bolts here in a month or two.
Thanks buddy. |
Re: 1960-1972 Lowering Block U bolts
Quote:
|
Re: 1960-1972 Lowering Block U bolts
Quote:
|
Re: 1960-1972 Lowering Block U bolts
Quote:
|
Re: 1960-1972 Lowering Block U bolts
Ok so today, after soaking for a couple of days with penetrant, I took the torch and cut the ubolts at the radius on both sides. I then took the impact and ran the nuts down till the bolts spun freely and viola, they fell right out. Piece of cake. Thank you all for the ideas.
|
Re: 1960-1972 Lowering Block U bolts
Quote:
|
Re: 1960-1972 Lowering Block U bolts
I will post pics later tonight when I get home.
Posted via Mobile Device |
Re: 1960-1972 Lowering Block U bolts
Can't wait to see them... :D
|
Re: 1960-1972 Lowering Block U bolts
Well I guess I can't post pictures from my phone so I will have till wait till I get back to a computer. So I will post before and after pics hopefully tomorrow
Posted via Mobile Device |
Re: 1960-1972 Lowering Block U bolts
2 Attachment(s)
Attachment 806691
Ok here is before the 1" drop block. Attachment 806692 And here is the after. Hard to notice the difference from these pictures but I can sure tell by the stance. |
Re: 1960-1972 Lowering Block U bolts
4 Attachment(s)
Attachment 806698
Attachment 806699 Ok and here an early, before the 1" lowering blocks and 5" springs, with the barden bumper still attached. Attachment 806700 Attachment 806701 And here is after some torchin and penitranting and bfh'n |
Re: 1960-1972 Lowering Block U bolts
ttt
|
Re: 1960-1972 Lowering Block U bolts
Sorry I'm late to the table! For archive reasons...I just did mine the other day. I hosed down the area with PB then ran the nuts down to the end. I then took my air hammer with a blunt tip and alternating between the two ends, hammered the u bolts up and out. A coupla DA DAs and they pushed right out.
|
Re: 1960-1972 Lowering Block U bolts
I'll take a set of bolts and blocks if I may....pm sent.
Money sent... |
Re: 1960-1972 Lowering Block U bolts
1 Attachment(s)
Got em!! and they are quality, plus they're U.S made...Thanks mate.
|
Re: 1960-1972 Lowering Block U bolts
wow, they got there pretty quick. Glad you're happy.
Thanks again mate! |
Re: 1960-1972 Lowering Block U bolts
Do you have a kit with 2 inch blocks available? I would like to purchase.
Thanks, Gary |
Re: 1960-1972 Lowering Block U bolts
Quote:
|
Re: 1960-1972 Lowering Block U bolts
1 Attachment(s)
Got my two inch blocks installed great product thanks boris...
|
Re: 1960-1972 Lowering Block U bolts
i need a set of 2in blocks and u-bolts how much to 98372 thanks ron
|
Re: 1960-1972 Lowering Block U bolts
I sent you a PM :smoke: Thanks, Nate
|
Re: 1960-1972 Lowering Block U bolts
I would like a set of 2" blocks and U bolt kit. Thanks
|
Re: 1960-1972 Lowering Block U bolts
Quote:
|
Re: 1960-1972 Lowering Block U bolts
Need quote on 2" u-bolt kit
|
Re: 1960-1972 Lowering Block U bolts
Borris
How about a set of u-bolts and 1.5" blocks sent to 75605? |
Quote:
|
Re: 1960-1972 Lowering Block U bolts
Checked my PM, did not get one from you. Can you try again...
|
All times are GMT -4. The time now is 08:11 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com