![]() |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Once Henry and I had a coffee and a chat plus did a short list of tasks to get to for the day, we headed down to the garage.
Decided to raise the rear end and fit the new rear shocks..... This is Henry’s happy face. OCD (One Chance Dude) When he came up for air after looking in under the truck. http://i294.photobucket.com/albums/m...ps2zyynqcg.jpg So what have we got here....?? Next to the license plate. http://i294.photobucket.com/albums/m...psrabsoxcd.jpg http://i294.photobucket.com/albums/m...psecfyrlw0.jpg Pipes....... WTF?? http://i294.photobucket.com/albums/m...psggx00jv4.jpg So it seems we have an adjustable rear air assisted shock combo with the springs fitted. The whole rear end was upgraded so that the truck could tow when it was used by John to do European trips. We dropped the rear and started on the front. Plan was to lubricate all the nipples, replace the front springs and shocks and reassemble at a more decent ride height. http://i294.photobucket.com/albums/m...pskhd9rjh6.jpg While under the front end, I measure the existing springs, they came up as 11 inches or about 280mm The springs PaulY gave me we’re part of a performance upgrade pack, and measure in at 17 inches. So surgery will certainly be on the books. Here are the specifications of a standard spring, only 13 inches it seems. http://i294.photobucket.com/albums/m...pslfvboj2j.png Ultimately, we could not get the lower ball joint to release, hammers, splitter etc..... So we eventually gave up, reassembled the front end and @PaulY will be over next weekend to help me again, possibly putting much more calculated force into splitting the ball joints. So once the tools were cleaned up, front end on the ground, another coffee and chat, we decided to quickly tackle the rear side panels that I had made and prepared through the week. Each fitted a side........ http://i294.photobucket.com/albums/m...psga52olmk.jpg Thankful to say that Captain OCD went in with a cloth and a tin of furniture polish to liven up the vinyl. Happy boy for sure. http://i294.photobucket.com/albums/m...psw4bms9wt.jpg Tailgate, glass, carpet and fabric cleaned up, thenspare wheel and great little tool bag for jack, fanbelts, pipes and a few spare bits back the rear. http://i294.photobucket.com/albums/m...psuxp6fqup.jpg I really do not think that the red looks that red in there now. On Sunday evening Dez Stringer posted up this pic, in there was a spare part for the truck, kindly donated by Kerry From Wales. http://i294.photobucket.com/albums/m...psukuihijm.jpg So a great weekend all in and as far as I am concerned, a lot achieved. Thank you all for looking in and your comments. Roll on Saturday. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Well.....
What a good day today turned out to be. I discovered a supply of this........ One of my all time favourites, and I do not care about anyone else’s feelings, opinions, and advice, unless it is on where to find more This is my emotional link with the USA http://i294.photobucket.com/albums/m...ps02jnqnwa.jpg Got a message from a friend in Siberia. Stas has sent me something by post, amazing weather they are having, yes I guess it is winter. http://i294.photobucket.com/albums/m...pscdo2ztaw.png While this was what my car said when I got back to it in the afternoon. Unseasonably warm weather for the first week of November http://i294.photobucket.com/albums/m...pseujsb42k.jpg Later guys. I trust some of you are interested in seeing the progress and random updates on the Blazer ?? |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Sunday evening I headed over to mate Martin to collect a table in Prozac.
From there it was over to Joys place for dinner and a dog walk. 200 meters up the street from her house was a pile of what looks like new carpet and foam underfelt. Prozac of course hit the brakes without me even trying, so I loaded a piece of each. Not the greatest colours........ http://i294.photobucket.com/albums/m...psbsptflmw.jpg Harley inspected and approved http://i294.photobucket.com/albums/m...ps2j7fjq2k.jpg So WTF and WHY ? Looking at the original 40year old carpets in the truck, 98% of it is good. But the drivers side has this damage and rot. http://i294.photobucket.com/albums/m...psczt2ul7a.jpg Looks like this if you lay it all flat. http://i294.photobucket.com/albums/m...psiw2q6xpy.jpg So I have enough to cover the whole front half of the truck including the rear foot wells. Do I just cut a wide strip to lay over the transmission hump and both front foot wells or remove the seats and lay it over all the existing carpet, or number three.... do I remove the original carpet and automotive underfelt, sound deadening and replace the 40year old sound deadening with some fresh new deadening pads? And then lay my residential underfelt and ugly blue carpet. Or just leave it as it is? Too many questions. JohnnyBravo suggested I go ghetto with the valves on the truck. I have a bunch of shotgun shells that will work on the wheel nuts too. http://i294.photobucket.com/albums/m...pshvmim2ov.jpg http://i294.photobucket.com/albums/m...psjxtwapkw.jpg |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Some more Artsy-Fartsy thinking required.
The truck has a grey fabric roof liner in the front above driver and passenger section, held in place with a bunch of pins. So, I bought this blanket last year some time at a Bootfair. So do I sacrifice it or put it away? http://i294.photobucket.com/albums/m...psf80gjm3o.jpg http://i294.photobucket.com/albums/m...ps18swdccj.jpg The plan is to remove and spray the rear glassfibre canopy in white Rhino liner on the outside and black on the inside, keeping it as it is, and just adding texture. Let’s see what you guys who know, think. Got home from London tonight and found a box in front of the kitchen door Wooooot !! Unpacked it and looked at what £320.00 buys you when you are building a “Not a project” car. http://i294.photobucket.com/albums/m...ps7hc9jkxa.jpg Remember last weekend Henry and I could not get the lower ball joint to release, despite loads of gentle and not so gentle wallops with big hammers. So @PaulY volunteered to come over next Saturday and use his mechanical know how of hammer blows to remove the lower ball joints so that I could get the replacement springs in. While chatting, we decided to replace the lower control arm ball joints, swiftly followed by me making a judegement call and deciding to replace upper control arm ball joints, tie rod ends, all the rubber bushes, wheel bearings, seals and front disc brake pads. AS THESE HAVE MOSTLY NEVER BEEN REPLACED. This should ensure an improved drive, handling and hopefully also the MOT for the next few years. I am getting the feeling more and more that this truck has actually only done 105k miles in its life, and being from California the lack of terminal rust on sheetmetal, and all the chrome looking as good as it does points in that direction. I could also be completely wrong. Anyway, hopefully, weather and rusted nuts permitting, we may have a rebuilt/serviced front end by Saturday evening. http://i294.photobucket.com/albums/m...ps6q2d9meo.jpg http://i294.photobucket.com/albums/m...psudydghqa.jpg So there you go. A list and pile of parts to make this Blazer even better than it is now. http://i294.photobucket.com/albums/m...psp8imzwvi.jpg Maybe this is now becoming a Project. Later. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Those of you following Dennis’ 1930’s gas station build on Prozacs thread may have wondered about it.
It continues for him, between day job and being variously occupied by life. Inside, held up by electrician. http://i294.photobucket.com/albums/m...psadvdpue1.jpg http://i294.photobucket.com/albums/m...psgpuvh3db.jpg Back on the Blazer, Glen Anderson suggested I do the must do’s first and then the like to’s So rather than do a whole bigncarpet job, I glued some of the thin red carpet under the torn pieces to keep it all together. http://i294.photobucket.com/albums/m...pscxk0exfq.jpg Then just cut some chunks of the house carpet to make runners and topped with a rubber mat. http://i294.photobucket.com/albums/m...ps61nl6cyg.jpg QC passed. http://i294.photobucket.com/albums/m...pstvwyuccf.jpg http://i294.photobucket.com/albums/m...pslb8eyiir.jpg Another small job done. Got a WhatsApp message from mate Ricky who bought my 66 C10 Chrome Smoothies a few years ago today. Hey mate, I have these rubber mats, would you like them for the Blazer? For the cost of collection at Bluebell Hill tonight? Hell Yeahhhhh!!!! Quick scrub, bit of soap, dry them, furniture polish to bring back the like new sheen, and Bobs your Aunty. Genuine GM items. Chuffed with that, Thanks a lot mate. http://i294.photobucket.com/albums/m...psfvb0uv4p.jpg http://i294.photobucket.com/albums/m...pseypqifkx.jpg And while we are at shiny stuff..... Stainless, laser cut. http://i294.photobucket.com/albums/m...psyylnetf4.png Or this one 🚐🦖 http://i294.photobucket.com/albums/m...psp4mkea6n.png Off to go fetch some rubber mats. I have taken the day off work tomorrow to stay home and play. Anyone fancy a cuppa, you know where to find me...... PM. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
[quote author="@darkspeed" source="/post/2456238/thread" timestamp="1540231731"][font size="6"]Projekt paint [/font]- well it fecking made me chuckle.[/quote]
Remember this.....?? Looks like a world of pain to me. http://i294.photobucket.com/albums/m...ps98j3e62h.jpg Very few people got it. So always good to see who reads the lines and between the lines. Continuing on the food theme, once I was onto beer number two, the starters got to us. Main course was even better and desert.......? A Twister each. http://i294.photobucket.com/albums/m...ps73dkkz2t.jpg After a great day in the garage, pretty much on my own, the evening spent with Joy was lovely, eventually got to bed by midnight and my friend insomnia stayed away till 5.30 which was a good night, up by 06.00 to feed Harley and up reading and writing. By 10.00 mate Henry got here from Romford, As can be expected, he brought provisions and tools (spring compressors) http://i294.photobucket.com/albums/m...psenc18o1g.jpg Earlier on, before Henry got here I did a few jobs. Measured the wheels and body height. Front http://i294.photobucket.com/albums/m...pstenh248z.jpg Rear. http://i294.photobucket.com/albums/m...psdxruqi55.jpg Then a lot of, well, two generous coats of this gloop. Over the primer and two coats of Zinc spray from Saturday, plus the seam sealer. http://i294.photobucket.com/albums/m...ps0tidpuq7.jpg Resulting in this underside, a great improvement imho. http://i294.photobucket.com/albums/m...psrrscpgh5.jpg Getting back to the top of the truck, outer sills and floor. I had destroyed the plastic sill with the welding heat, so pulled it off. Then Martin to the rescue again. Old MX5 sills, also needing some trimming to fit and rebadging. http://i294.photobucket.com/albums/m...ps0gk6xhm9.jpg http://i294.photobucket.com/albums/m...pspwp0gfei.jpg And as mentioned....... This is not a project. I am super pleased with the final outcome of the floor. Really pleased. http://i294.photobucket.com/albums/m...psmrszrkxi.jpg Did I mention I was pleased with that floor.....? |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
I am not sure if any of you are actually interested in, or bothered with my posting up on here.
Hope the metal repairs for a non project truck, passes muster. Once Henry and I had a coffee and a chat plus did a short list of tasks to get to for the day, we headed down to the garage. Decided to raise the rear end and fit the new rear shocks..... This is Henry’s happy face. OCD (One Chance Dude) When he came up for air after looking in under the truck. http://i294.photobucket.com/albums/m...ps2zyynqcg.jpg So what have we got here....?? Next to the license plate. http://i294.photobucket.com/albums/m...psrabsoxcd.jpg http://i294.photobucket.com/albums/m...psecfyrlw0.jpg Pipes....... WTF?? http://i294.photobucket.com/albums/m...psggx00jv4.jpg So it seems we have an adjustable rear air assisted shock combo with the springs fitted. The whole rear end was upgraded so that the truck could tow when it was used by John to do European trips. We dropped the rear and started on the front. Plan was to lubricate all the nipples, replace the front springs and shocks and reassemble at a more decent ride height. http://i294.photobucket.com/albums/m...pskhd9rjh6.jpg While under the front end, I measure the existing springs, they came up as 11 inches or about 280mm The springs PaulY gave me we’re part of a performance upgrade pack, and measure in at 17 inches. So surgery will certainly be on the books. Here are the specifications of a standard spring, only 13 inches it seems. http://i294.photobucket.com/albums/m...pslfvboj2j.png Ultimately, we could not get the lower ball joint to release, hammers, splitter etc..... So we eventually gave up, reassembled the front end and @PaulY will be over next weekend to help me again, possibly putting much more calculated force into splitting the ball joints. So once the tools were cleaned up, front end on the ground, another coffee and chat, we decided to quickly tackle the rear side panels that I had made and prepared through the week. Each fitted a side........ http://i294.photobucket.com/albums/m...psga52olmk.jpg Thankful to say that Captain OCD went in with a cloth and a tin of furniture polish to liven up the vinyl. Happy boy for sure. http://i294.photobucket.com/albums/m...psw4bms9wt.jpg Tailgate, glass, carpet and fabric cleaned up, thenspare wheel and great little tool bag for jack, fanbelts, pipes and a few spare bits back the rear. http://i294.photobucket.com/albums/m...psuxp6fqup.jpg I really do not think that the red looks that red in there now. On Sunday evening Dez Stringer posted up this pic, in there was a spare part for the truck, kindly donated by Kerry From Wales. http://i294.photobucket.com/albums/m...psukuihijm.jpg So a great weekend all in and as far as I am concerned, a lot achieved. Thank you all for looking in and your comments. Roll on Saturday. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Sunday evening I headed over to mate Martin to collect a table in Prozac.
From there it was over to Joys place for dinner and a dog walk. 200 meters up the street from her house was a pile of what looks like new carpet and foam underfelt. Prozac of course hit the brakes without me even trying, so I loaded a piece of each. Not the greatest colours........ http://i294.photobucket.com/albums/m...psbsptflmw.jpg Harley inspected and approved http://i294.photobucket.com/albums/m...ps2j7fjq2k.jpg So WTF and WHY ? Looking at the original 40year old carpets in the truck, 98% of it is good. But the drivers side has this damage and rot. http://i294.photobucket.com/albums/m...psczt2ul7a.jpg Looks like this if you lay it all flat. http://i294.photobucket.com/albums/m...psiw2q6xpy.jpg So I have enough to cover the whole front half of the truck including the rear foot wells. Do I just cut a wide strip to lay over the transmission hump and both front foot wells or remove the seats and lay it over all the existing carpet, or number three.... do I remove the original carpet and automotive underfelt, sound deadening and replace the 40year old sound deadening with some fresh new deadening pads? And then lay my residential underfelt and ugly blue carpet. Or just leave it as it is? Too many questions. JohnnyBravo suggested I go ghetto with the valves on the truck. I have a bunch of shotgun shells that will work on the wheel nuts too. http://i294.photobucket.com/albums/m...pshvmim2ov.jpg http://i294.photobucket.com/albums/m...psjxtwapkw.jpg Some more Artsy-Fartsy thinking required. The truck has a grey fabric roof liner in the front above driver and passenger section, held in place with a bunch of pins. So, I bought this blanket last year some time at a Bootfair. So do I sacrifice it or put it away? http://i294.photobucket.com/albums/m...psf80gjm3o.jpg http://i294.photobucket.com/albums/m...ps18swdccj.jpg The plan is to remove and spray the rear glassfibre canopy in white Rhino liner on the outside and black on the inside, keeping it as it is, and just adding texture. Let’s see what you guys who know, think. Got home from London tonight and found a box in front of the kitchen door Wooooot !! Unpacked it and looked at what £320.00 buys you when you are building a “Not a project” car. http://i294.photobucket.com/albums/m...ps7hc9jkxa.jpg Remember last weekend Henry and I could not get the lower ball joint to release, despite loads of gentle and not so gentle wallops with big hammers. So @PaulY volunteered to come over next Saturday and use his mechanical know how of hammer blows to remove the lower ball joints so that I could get the replacement springs in. While chatting, we decided to replace the lower control arm ball joints, swiftly followed by me making a judegement call and deciding to replace upper control arm ball joints, tie rod ends, all the rubber bushes, wheel bearings, seals and front disc brake pads. AS THESE HAVE MOSTLY NEVER BEEN REPLACED. This should ensure an improved drive, handling and hopefully also the MOT for the next few years. I am getting the feeling more and more that this truck has actually only done 105k miles in its life, and being from California the lack of terminal rust on sheetmetal, and all the chrome looking as good as it does points in that direction. I could also be completely wrong. Anyway, hopefully, weather and rusted nuts permitting, we may have a rebuilt/serviced front end by Saturday evening. http://i294.photobucket.com/albums/m...ps6q2d9meo.jpg http://i294.photobucket.com/albums/m...psudydghqa.jpg So there you go. A list and pile of parts to make this Blazer even better than it is now. http://i294.photobucket.com/albums/m...psp8imzwvi.jpg Maybe this is now becoming a Project. Later. Those of you following Dennis’ 1930’s gas station build on Prozacs thread may have wondered about it. It continues for him, between day job and being variously occupied by life. Inside, held up by electrician. http://i294.photobucket.com/albums/m...psadvdpue1.jpg http://i294.photobucket.com/albums/m...psgpuvh3db.jpg Back on the Blazer, Glen Anderson suggested I do the must do’s first and then the like to’s So rather than do a whole bigncarpet job, I glued some of the thin red carpet under the torn pieces to keep it all together. http://i294.photobucket.com/albums/m...pscxk0exfq.jpg Then just cut some chunks of the house carpet to make runners and topped with a rubber mat. http://i294.photobucket.com/albums/m...ps61nl6cyg.jpg QC passed. http://i294.photobucket.com/albums/m...pstvwyuccf.jpg http://i294.photobucket.com/albums/m...pslb8eyiir.jpg Another small job done. Got a WhatsApp message from mate Ricky who bought my 66 C10 Chrome Smoothies a few years ago today. Hey mate, I have these rubber mats, would you like them for the Blazer? For the cost of collection at Bluebell Hill tonight? Hell Yeahhhhh!!!! Quick scrub, bit of soap, dry them, furniture polish to bring back the like new sheen, and Bobs your Aunty. Genuine GM items. Chuffed with that, Thanks a lot mate. http://i294.photobucket.com/albums/m...psfvb0uv4p.jpg http://i294.photobucket.com/albums/m...pseypqifkx.jpg And while we are at shiny stuff..... Stainless, laser cut. http://i294.photobucket.com/albums/m...psyylnetf4.png Or this one 🚐🦖 http://i294.photobucket.com/albums/m...psp4mkea6n.png Off to go fetch some rubber mats. I have taken the day off work tomorrow to stay home and play. Anyone fancy a cuppa, you know where to find me...... PM. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Went over to Robin Hood Pub and met up with some of the BHRA guys, along with Ricky.
Had a drink, few hours chat and then came home. Of course scrubbing mats at 10.00pm out back is nothing unusual. Came out good. http://i294.photobucket.com/albums/m...psxjutqxvm.jpg Tomorrow I will add a bit of furniture polish to make them pop and fit them. Loving this non project truck. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Quote:
Only sold in man sizes XXL up yo 4XL :mm: Waiting for daylight so I can get on down to the shop. 1’C out there this morning. May see me in an overall and shoes today. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
So last night, Ricky who brought me the mats for the truck, knowing I like a knife, and also that I love miniature items, brought me a serious dagger.
http://i294.photobucket.com/albums/m...psreac6osp.jpg http://i294.photobucket.com/albums/m...ps4hcoaydo.jpg After adding a bit of shine to the mats, as well as cleaning the previous set I had, that then went in for the rear seat, it looked like this. I love it for sure. http://i294.photobucket.com/albums/m...pswm8bkftb.jpg It rained intermittently today, typical of the day I chose to take off work. So I did lots of little random jobs in the garage, moved stuff about, made some space. Also grabbed a large can of satin black, and after cleaning the wheels, I sprayed the centres three coats of black. Next will be Silver Hammerite paint along the edge. http://i294.photobucket.com/albums/m...psihuvafun.jpg http://i294.photobucket.com/albums/m...psprnacsgj.jpg One of today’s planned tasks was to modify the VW Polo Towbar to make it fit the Blazer chassis. http://i294.photobucket.com/albums/m...psem2wmkro.jpg http://i294.photobucket.com/albums/m...pscgxrix3i.jpg I believe this is where Lee, the previous owner had removed the old Towbar. So it will be the new mounting point once I figure it all out. http://i294.photobucket.com/albums/m...psfhs2i8yh.jpg Up it goes. And yes, axle stands too. http://i294.photobucket.com/albums/m...psyyyjxoi0.jpg Coffee break looked like this, and I got optimistic, only to be rained out 20 minutes later again. Grrrrrrr....!! http://i294.photobucket.com/albums/m...psahzv5n7m.jpg |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
As isoften thecase, in this case the third time this week....
Prozac had ajob to do. Headed over to PaulF’s tocollect his hydraulic press. Will be needing that tomorrow. His splits meeting Prozac, http://i294.photobucket.com/albums/m...ps21gdxmge.jpg Loaded along with a 1960 vintage table that was in the back of Prozac already http://i294.photobucket.com/albums/m...pssd1dfknm.jpg Back at home, security had to check. http://i294.photobucket.com/albums/m...pseuktarht.jpg Moving it from Prozac to garage. Amazing how easy the wheels made it. http://i294.photobucket.com/albums/m...psui3eakzw.jpg Waiting for tomorrow when @PaulY gets here. http://i294.photobucket.com/albums/m...psozcw6s0z.jpg Then back to the Towbar issue, needing to be mounted off the chassis. http://i294.photobucket.com/albums/m...pswlqqv9pm.jpg Measure, visualise and http://i294.photobucket.com/albums/m...pslpdss7oa.jpg Cut http://i294.photobucket.com/albums/m...pskofaxjwm.jpg And finally trimmed to size, http://i294.photobucket.com/albums/m...pseo7cwwyj.jpg Ready to be welded and fitted. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Anyone interested.....?
So Saturday started thus. http://i294.photobucket.com/albums/m...pssn44ddil.jpg I got the truck off the rear axle stands and then turned it around on the lawn, not a clever thing as there are a load of wheel tracks/trenches from the weight of the truck. I usually reverse stuff down the drive as it’s easier that way, but when @PaulY got there we would be needing the front end facing the garage entrance. A rare sight this way around. http://i294.photobucket.com/albums/m...pslinhdryi.jpg Up on axle stands, wheels off and tools ready so that when Paul got there by 10.30 we could carry on. http://i294.photobucket.com/albums/m...psyjuqhyij.jpg Mickey came around to check up on us as he heard the motor earlier on. http://i294.photobucket.com/albums/m...psmtwottaq.jpg This guy has always got a smile, even when things go badly wrong, he just grins and says something like “well, let’s think about it, we just need to get on and do this thing” http://i294.photobucket.com/albums/m...psmhjrkprv.jpg The blue house carpet I brought home last week came in handy, two layers helped against the bone chilling cold while the wind continued to drop the temperature for us. Busy Busy Busy...... and yes, I helped (a little bit) http://i294.photobucket.com/albums/m...pss7hqhboc.jpg DIRTY BIG THING, DIRTY DIRTY DIRTY. Lower control arm. http://i294.photobucket.com/albums/m...pshsrfclbw.jpg Scrape, dig, clean up using knife, chisel and brush, then washed with a hard toilet brush and loads of petrol. http://i294.photobucket.com/albums/m...psrtf8i72r.jpg Followed by commercial kitchen degreaser that smelled lovely. Then once it dried away, pressure clean, wash and dry. http://i294.photobucket.com/albums/m...ps1aoo7wyk.jpg Clean parts are so much fun to work with. The 40 year old bushes and ball joints still needed to be removed. More in a bit. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
So we continued to dismantle, clean, strip and swear from time to time. (I do most of the swearing, @PaulY jut get on with it)
The amount of dirt stuck to this truck, possibly the same as most or many other 40 year olds is staggering, possible a good rust preventative though. Both sides torn down. http://i294.photobucket.com/albums/m...psd93wdome.jpg Next job of course was to clean, service and refit new parts to the Control arms. http://i294.photobucket.com/albums/m...psnyygznid.jpg The springs removed form the truck were as impressive as any that had been torched before. Useful only as ballast when weighing something in. Take a good look. Before you burn them. Measuring 11 inches. http://i294.photobucket.com/albums/m...psypyjwx5d.jpg So a new pair were selected from the pile, and measured, offered up and then Dr Bosch Grinder came in. Surgery. 13 inches saved to be fitted. Happy. http://i294.photobucket.com/albums/m...pshh6c5ssy.jpg The next big job was a YouTube research job...... Easiest way to remove the 40 year old swing arm bushes. Dr Bosch Drill to theatre. Bench mounted, a few large drill bits sacrificed Two per swing arm = 8 total. http://i294.photobucket.com/albums/m...ps9qwtwice.jpg Followed by Mr Press. This tool, belonging to @PaulF was the most sensible thing to bring to the party. Not always easy to use, needed loads of small custom pressing pieces made through the day, each taking time, and finding the right materials being a pain too, it worked a treat. http://i294.photobucket.com/albums/m...psadzbrcic.jpg New brake shoes added while the front end was dismantled. http://i294.photobucket.com/albums/m...psttpmmh2y.jpg As we got busier and time drained away, I took less photos. Needles to say, once the old bushes were removed and the new once’s pressed into place, often necessitating restarts the Ball joints were removed, replaced and then I took each piece out to a tree, hung them and painted the fresh metal in underbody sealer, getting a lovely uniform and clean look. By 8.30 Paul had completed the reassembly, I still need to go back to torque up everything, change the position of the passenger side lover swing arm arm as it seems to have escaped the locating points. Brake on passenger side needs bleeding. Then I need to do the steering or tie rod ends, as we ran out of daylight and ambition, the cold is a killer. Finally I also need to remove and replace the existing front wheel bearings. BRILLIANT LINK. http://www.73-87.com/7387garage/chas...n/frontend.htm Tired but happy, we closed shop at 8.30 Sleep was a problem for me, netting a total of three hours, and then awake for 4 hours, followed by another hour. Today it was rain, wind and 5’C all day, so I decided to go shopping for food, paint and Silver Hammmerite for the wheels once the sun returns. This afternoon I popped down to the garage to check the height and get a pic of the new height. A sure sign of us being tired toward the end. http://i294.photobucket.com/albums/m...psfxwgpbvs.jpg Front end came up 35 mm Looking a load better, rear seems to have gone down a bit, 5-10mm http://i294.photobucket.com/albums/m...psutnkzfsr.jpg So there you go. One step closer to an MOT submission. Thanks for checking in and making your comments all. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
[quote author="@glenanderson" source="/post/2457485/thread" timestamp="1540741183"]Up 35mm and with springs that might actually have some spring in them. Good job. I’m certain you’ll notice a huge difference.
I’d have come up a bit more, personally, but that’s a whole lot better than it was, whilst still leaving me room to knock you down when you sell it to me. I reckon the back could be left as it is now. [/quote] Correct, and funny, with action, I would be happy visually to go down, so leaving the front end just where it is. [quote author="@braaap" source="/post/2457488/thread" timestamp="1540742085"]Cutting the springs to a certain legth is one thing, but do you know the spring rates of the new ones or is the thread thickness the same? If they were made for a lighter car, the car might sit lower after the first miles. Or the springs start settling because of their material. Only time will tell I think. Nice job nevertheless.[/quote] Thank you very much, I am both thankful and pleased for Paul’s help. Doing it is one thing, doing it all fast, and knowing what you are doing is another, thankfully it was another. [quote author="@pauly" source="/post/2457500/thread" timestamp="1540744010"]@braaap is quite right. It will settle a bit but probably not that much. All the springs where sacrifices to the Gods of Lows (tm) when I was trying to fine tune the ride height on my 56 PU - the coils are slightly 'lighter' but only time will tell. In other news Grizz's new toy is a lot better in the flesh than he makes out in his posts. Good job it is not a project as I think this will morph into the new Prozac over the coming months. Onwards! P. :D[/quote] Thank you Paul, yes the truck is much better than described according to everyone who has seen it. Guess I just like to manage my own expectations, hence it still making me happy. And yes, agreed, it will evolve. I know everything I do to it, will increase its inherent value. Thanks to your expert guidance I have now just ordered a set of these. http://i294.photobucket.com/albums/m...psgcmk2f7y.jpg http://i294.photobucket.com/albums/m...psbzoljtem.jpg And so ends another good MoJo filled weekend. Thought I would post up a few useful or interesting links. THANK YOU TO THOSE RESPONSIBLE FOR CREATING THESE RESOURCES. FRONT END REBUILD TUTORIAL http://www.73-87.com/7387garage/chas...n/frontend.htm BLAZER PICTURE THREAD http://67-72chevytrucks.com/vboard/s...d.php?t=331470 FULL AND COMPLETE 1979 CHEVY LIGHT TRUCK SERVICE MANUAL. http://www.73-87chevytrucks.com/tech...ice_Manual.pdf Garage cat warning. http://i294.photobucket.com/albums/m...pslo3orbsb.jpg Someone asked if the Teardrop Trailer still existed. Yes it certainly does. http://i294.photobucket.com/albums/m...psr1haupel.jpg And it seems Dennis has pretty much used up all the wood on his gas station replica build. Perfect timing for a winter outfit, now the inner walls, insulation and electrics are done. http://i294.photobucket.com/albums/m...psapomzuub.jpg With winters chill and short days here, it looks like the truck will mainly be getting weekend time now. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Went down to the garage a few minutes ago, it’s bloody cold out there.
Wanted to check and see if my bought 10 years ago, used a few times, Torque Wrench still worked. http://i294.photobucket.com/albums/m...psejbyyh80.jpg http://i294.photobucket.com/albums/m...pspgqqhdru.jpg Quick bit of random stuff to add. Some of the other good things that has happened under the hood. Like the suspension parts, brakes etc that I have replaced, regardless of condition so that I know we have a decent baseline.... The truck has benefitted from a new water pump, new hoses, HT leads, plugs, oils, filters and a brake master cylinder and rebuilt front brake Callipers, radiator fan to replace the original viscous unit. Tyres you will note are new... So loads of good stuff. http://i294.photobucket.com/albums/m...psp3gqmrwl.jpg http://i294.photobucket.com/albums/m...psswgzshyo.jpg ONCE AGAIN, LOOKING FOR SOMETHING......... A SMALL KNOB. http://i294.photobucket.com/albums/m...ps3l7ee4kz.jpg At Dennis things are really coming together. http://i294.photobucket.com/albums/m...pszlezkend.jpg Interior. Insulated, wired up and thick Wood panelled http://i294.photobucket.com/albums/m...pse5uhsgh5.jpg |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Needs more thought.
[quote author="@darrenh" source="/post/2458411/thread" timestamp="1541068837"]is that wound spring of hard brake hose an original feature? just made me smile as it seems quite a logical idea[/quote] If you want to do it, I found using a double dose of good masking tape to hold the pipe in the start position, and then to wind the pipe tightly around the can till you have the righ spirals. After this, I used the can as a lever to twist the pipe till it was basically in the right position. http://i294.photobucket.com/albums/m...psqmub3tg0.jpg First pipe bent and ready to wait for the rebuild to complete. They have to follow the inner fender profile and then end up under the hood next to the master cylinder. http://i294.photobucket.com/albums/m...psof0zjn8b.jpg Second one done....... http://i294.photobucket.com/albums/m...ps2mjlvimo.jpg [quote author="@da1sycat" source="/post/2458539/thread" timestamp="1541102587"]Grizz I really do look forward to your updates no matter what the topic. I admire your “we will overcome attitude” too and when reading about the mismatch between the bits and pieces as per the wisdom of Dennis I just couldn’t help think of one of my favourite Johnny Cash tracks “One Piece at a Time” “The transmission was a fifty three And the motor turned out to be a seventy three And when we tried to put in the bolts all the holes were gone. So we drilled it out so that it would fit And with a little bit of help with an adapter kit We had that engine runnin' just like a song Now the headlight' was another sight We had two on the left and one on the right But when we pulled out the switch all three of 'em come on.” And of course the last verse when the great Man in Black describes the year of manufacture lol. Isn’t it brilliant that US Autos can be put together with several different model years? Try that with anything other than a Landrover and you’d be left with more adapters than parts! Roll on the next instalment. [/quote] Love that song. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
As with many cars, especially the older ones, the most wanted, purest form Blazers were the originals.
Over the years they have evolved a lot. Originals lost the whole roof...... This makes them coveted. By the time 1979 and my Blazer rolled in, the drivers or front roof section had become fixed, with only the rear fiber glass or is that glassfibre canopy section unbolting and lifting away, leaving you with a very basic truck like profile. The canopy side glass also became available with sliding glass, I prefer the look of solid glass. Front ends and hoods/bonnets kept changing too in order to keep people interested. Single round headlights,evolved through square and double stacked etc. I found a 2WD Blazer, Jimmy, Suburban thread of 52 pages and pulled off some pics to add in here, partly as reference, but also because it reminds me that in summer this truck may just become even more fun. Did I say FUN ? Or [font size="5"][font color="e63b19"]FUN[/font][/font] DISCLAIMER. Please keep in mind that there are no plans for fancy paint jobs, 22” wheels, turbos, blowers etc, http://i294.photobucket.com/albums/m...s64yahmg0.jpeg http://i294.photobucket.com/albums/m...sxzhpy6tg.jpeg http://i294.photobucket.com/albums/m...srgyx4jeo.jpeg http://i294.photobucket.com/albums/m...sbj4ipiju.jpeg Love everything about this truck. And would love one of these hoods for my truck with the bulge. http://i294.photobucket.com/albums/m...s6lf17sw7.jpeg Same truck, big wheels that are not my taste at all. http://i294.photobucket.com/albums/m...shiufdjwj.jpeg http://i294.photobucket.com/albums/m...sbtgmi510.jpeg http://i294.photobucket.com/albums/m...s3loqthds.jpeg Great colour combo, same series as my Blazer. http://i294.photobucket.com/albums/m...sblhgf2fr.jpeg http://i294.photobucket.com/albums/m...ssrgcfwun.jpeg http://i294.photobucket.com/albums/m...suqey0jhr.jpeg http://i294.photobucket.com/albums/m...sk0fjfyai.jpeg http://i294.photobucket.com/albums/m...sibqsmwdc.jpeg http://i294.photobucket.com/albums/m...skfn3wvdn.jpeg Really like this, despite the current paint status. http://i294.photobucket.com/albums/m...s88tjv160.jpeg http://i294.photobucket.com/albums/m...s6uy9f7lg.jpeg http://i294.photobucket.com/albums/m...skossomyn.jpeg http://i294.photobucket.com/albums/m...sogzb1jer.jpeg http://i294.photobucket.com/albums/m...sblxzuzoi.jpeg http://i294.photobucket.com/albums/m...slqkzqzgi.jpeg So there you have a mix, just to feast your eyes, and for ideas together in one place. Thank you to the owners who posted up the original photos that I have pulled together on here. Do feel free to add more if you have more TOPLESS Blazers. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Going back a few years now.
On my first USA road trip, this was one seen in Texarkana. Next we heard the unmistakable rumble of large bore straight through pipes and Scott pulled up. Niiiiiiiiice...!! http://i294.photobucket.com/albums/m...pspnwxq8wf.jpg http://i294.photobucket.com/albums/m...psnq6bdevu.jpg I just Loved the headlights. http://i294.photobucket.com/albums/m...pslipjiiew.jpg |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
So....
Friday night. Been a busy week. Worked with the new boss on Monday, the rest of the week was busy, read busy. Today I was booked into an all day Skype training course on Cancer and Cancer Associated Thrombosis, or CAT in short. Since temperatures dropped, it seems I have a CAT in bed nightly. http://i294.photobucket.com/albums/m...psqz37vmxv.jpg I have realised I need a “Cowl Hood” to replace the one the truck came with. And looking around FB marketplace for a hood/bonnet, I happened on a radiator shroud. Messaged the seller over in Essex 50 miles from where I live, while on my Skype training, agreed to a price, based on Autojumble prices of £10.00 or $13.00 which if you realistically added the Darford Crossing Toll fee and cost of using my company car at 11p/mile worked out to around £25.00 or $35.00 for the fan shroud...... I could not get one from the USA for that money. So after training, I drove over to Sean’s place, Met his dad and cats, and spent an hour talking cars, trucks and Triumph bikes..... The shroud came from this 1908 GMC Truck, currently diesel, and actually sold tonight. Sean also has an Advanced Design Chevy truck, getting a monster diesel. The guys like their diesels. http://i294.photobucket.com/albums/m...psytufzesy.jpg While in their shop, his dad showed me the hood to his truck. Love the pinstriping. @mrtiki should approve http://i294.photobucket.com/albums/m...ps1trkyft5.jpg Now this is another Item I would absolutely love to have for myself. http://i294.photobucket.com/albums/m...psmcvmalsu.jpg Back home by after 4pm, I just unpacked and then fed the cat........ Took pics of my bit of joy, front and rear. Will see if it fits tomorrow http://i294.photobucket.com/albums/m...psevjy8bmj.jpg http://i294.photobucket.com/albums/m...psmspjcwz6.jpg Lastly, I found this on the floor under the truck. Wonder where it came from. http://i294.photobucket.com/albums/m...psq6m5zzj6.jpg Tomorrow it’s back under the front end. Wish me luck. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Insomnia Sucks.
Waking at 04.00 on a weekend sucks. Waking to this does not suck. http://i294.photobucket.com/albums/m...ps8bvpyooo.jpg Garage time today. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
After last weekend and the spring replacement, Mate Martin sent this pic today.
Made me smile, because a certain @PaulY has seen this go wrong before. http://i294.photobucket.com/albums/m...psdisrhuaj.jpg After last weekends 10 hr session at 5’C in the cutting wind and out on the driveway, we shut shop and I had a hectic week, which meant I never cleaned up, or cleaned the tools that were all covered in 40 year old black grease, as well as all the debris from the days work. So this morning after going to the Post office at 07.45 and then to Aldi for food as I planned on cooking dinner over at Joys place tonight (she has been ill 10days now, and I refused to go there and get infected) I proceeded to,spend two hours cleaning up. The brake shoes that came out of the truck were at various levels of wear or destruction. http://i294.photobucket.com/albums/m...psn6yf4xo1.jpg The top, cracked one had also worn quite thin. http://i294.photobucket.com/albums/m...pssbmaj9rv.jpg Really pleased and thankful that all these “little jobs” are getting done. Makes life a lot easier in the long run. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
So one of the jobs that we just had to walk away from last weekend after 10 hrs in the cold, was the passenger side lower control arm and its cross shaft, which has locating pins on the cross me,her.
These have to be seated, or else you cannot tighten the U-Bolts. In the dark at 7pm it was never going to happen. So today I had to fix it hat as a first priority. I certainly was not going to disassemble everything, so took a long look, and tried to see in there, but of course there is a lot that goes on there, and even the LED torch could not give me enough of an idea as to where the pins and holes were http://i294.photobucket.com/albums/m...ps4d6o6myx.jpg So I undid the U-Bolts a bit, lifting the whole assembly gently with the jack from under the spring cup. No matter what I tried I could not see what needed to be done, did it need to be twisted forward or backward and did I need to attack it with a rubber mallet from the rear or from the front. So I came up to the house for a coffee, and cookies...... thinking power food. And thought that the only way to figure out where everything was in relation to everything else, was to poke my finger in there, and then twist and hammer into various directions. But my thick fingers would not fit in the space I had available. So I used some wire, sharpened it, created a simple handle to give me leverage. This way I got to “feel and pick”the invisible space between cross shaft and mounting point and the locating pin and hole. http://i294.photobucket.com/albums/m...psmcvlt6wg.jpg Trust me, this was a long job, simply because I am not naturally talented like some mechanics. My neck hurt, and I was hurting because despite,the,carpet on the floor, the cold does come up into my back. http://i294.photobucket.com/albums/m...psm4jlnpcw.jpg EVENTUALLY I GOT IT ALL SORTED AND BOLTED DOWN. http://i294.photobucket.com/albums/m...psqtcumd55.jpg This job was followed by the steering tie rod ends. Theoretically a simple take it off and replace it job. Errrrmmm,mmmmm........? http://i294.photobucket.com/albums/m...ps9fkg2ilj.jpg http://i294.photobucket.com/albums/m...psmmptlg93.jpg These old parts really are grubby, rusted and a pain. 34 turns to remove the old unit. http://i294.photobucket.com/albums/m...pswbbhpeke.jpg THEN THE FUN STARTED. I could not for the life of me, get the new part to screw into the jointing section, at least not the way it had come out. I think in the end I may even have cross threaded it too. Copper slip added, but all to no avail. http://i294.photobucket.com/albums/m...psbms0h1rd.jpg So the question is this: Do these units come in a left hand and a right hand flavour? The two that I got sent are exactly the same, and an hour later I still had no progress and shut shop as I had a dinner date after showering and feeding Harley. Packaging. http://i294.photobucket.com/albums/m...psrvd9hvqt.jpg Both are exactly the same. http://i294.photobucket.com/albums/m...psoaczyczs.jpg Tomorrow morning I will go try to do the drivers side and if it is a simple task, then who knows, it may be that there are Left and Right Toe Rods. Anyone know? Bedtime. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
So Sunday morning I approached it all again.
Based on various comments on the forums I looked closer at what I had. http://i294.photobucket.com/albums/m...ps1yb98js0.png Karl “Aggie” from Longview, Texas also commented and added further advice. Making sense to the ownership of a 40 year old truck. Quote:
New parts should only improve things further. And looking at the receipt and numbers from my order it seems the order was correct but wrong items picked and shipped. http://i294.photobucket.com/albums/m...psmx5ftzxb.jpg So these are the inner tie rod ends. Based on the LT code. http://i294.photobucket.com/albums/m...psteotzkcj.jpg http://i294.photobucket.com/albums/m...pssphukerg.jpg So once I realised I could not complete the job, I removed, cleaned and greased up the drivers side too and refitted both sides http://i294.photobucket.com/albums/m...psons0nqsv.jpg Next up was further cleaning up of all the underside parts, nuts and surfaces. Then greasing up all the grease points. http://i294.photobucket.com/albums/m...pscgmwa6ix.jpg Once all was cleaned up, bolted down, I torqued down every nut, keeping in mind the control arms needed to be done under full load. This was done by making a small adapter for the jack to fit the lower ball joint grease nipple into and raising the front suspension till it lifted the truck, creating full load. I followed with a final coat of Würth underbody sealer. http://i294.photobucket.com/albums/m...ps1d44ivc1.jpg Happy with the outcome. Passenger side. http://i294.photobucket.com/albums/m...ps8g3bamrv.jpg Drivers side. http://i294.photobucket.com/albums/m...psdxcs8mbm.jpg I then refitted the wheels and brought the truck down to the ground. Rocking it hard in all directions it was almost dark but I got one photo. Will do some in daylight after a drive. The final wheel arch height has gone from 680mm up to a much better looking 740mm So a ain of 60mm with thenew parts and springs. http://i294.photobucket.com/albums/m...psyj1vpjkm.jpg Final job to do will be to get sone DOT4 Brake Fluid to top up and bleed the brakes. Then it should be all go for MOT when I get a chance. Did I mention that this is “Not a Project” Later. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Wheels.......
Last week a member on a FB forum directed me toward these Stainless trim rings. http://i294.photobucket.com/albums/m...psnttoopmz.jpg Advertised as this. So including courier cost DPD who certainly will not get my business again for taking 4days to do an overnight £10.00 delivery, it was £60.00 for the trim rings. So I agreed to buy them. http://i294.photobucket.com/albums/m...ps6rwip2t3.jpg Similar to the trim rings I have ready for the C10 along with the Rallye wheels I bought a few years ago. I did try them on the Blazer rims, but no fit. http://i294.photobucket.com/albums/m...psjnppbeuz.jpg Plan is to go satin black Centre and Chrome/Stainless trims. http://i294.photobucket.com/albums/m...psprnacsgj.jpg So tonight after work I got home to these. http://i294.photobucket.com/albums/m...psyt5bvngh.jpg New, in the box, actually nor even opened since they were shipped. Quick Catscan from Security cat. 68mm deep trims, should look good. http://i294.photobucket.com/albums/m...ps3fkm3zf5.jpg I never went down to see if they fitted, as it was cold and damp and dark. On the way to Physio I stopped in at my favourite spares store and got som brake fluid to top up and bleed the brakes. http://i294.photobucket.com/albums/m...pslwkojagi.jpg Hope to get the brakes done by Sunday. Thanks for checking in. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Well.....
What a good day today turned out to be. I discovered a supply of this........ One of my all time favourites, and I do not care about anyone else’s feelings, opinions, and advice, unless it is on where to find more This is my emotional link with the USA http://i294.photobucket.com/albums/m...ps02jnqnwa.jpg Got a message from a friend in Siberia. Stas has sent me something by post, amazing weather they are having, yes I guess it is winter. http://i294.photobucket.com/albums/m...pscdo2ztaw.png While this was what my car said when I got back to it in the afternoon. Unseasonably warm weather for the first week of November http://i294.photobucket.com/albums/m...pseujsb42k.jpg Had to spend a few hours at my desk this morning, working from home has its advantages too. Just not sure what they are. But.... The doorbell went, usually I would be long gone by then. Went downstairs to answer the door...... Wooohooo. Brown Van Man. Bearing gifts, well one gift, that I had ordered and paid for yesterday. Less than 24 hrs delivery, certainly beat DPD and their four day overnight delivery. http://i294.photobucket.com/albums/m...pskiilmf4u.jpg Opened the parcel once I had done my admin and before I left. More Steering parts. http://i294.photobucket.com/albums/m...ps60rwteph.jpg After work tonight I got home and found an envelope that had been sent by Dale who hadnotived the truck was missing a knob (other than me) Thank you mate. http://i294.photobucket.com/albums/m...psrtbszexl.jpg So once I had changed into house clothes Iwent down to the garage. Knob fitted and wipers and washer tested. http://i294.photobucket.com/albums/m...pszpikpxko.jpg While down there, I noticed gauges were all showing different lies. Ignition not on, but oil pressure, temp gauge showing life, and the clock broken completely So more investigation to come, http://i294.photobucket.com/albums/m...psulxemvwy.jpg I have to say that a few guys have been really helpful since I bought the Blazer. Most of all has been Dennis in St Louis, he owned a few of there Square bodies and knows their deepest secrets, so he has been advising and ensuring I do not screw up completely from behind the scenes. I love the internet. Then the fun part. http://i294.photobucket.com/albums/m...pszvnwpgd6.jpg All threads also covered in Copaslip..... future proofing the steering parts. http://i294.photobucket.com/albums/m...pssysak5ep.jpg And of course all the grease nipples in place, primed and cleaned up. Nothing like a DIY selfie to wrap up the evening. http://i294.photobucket.com/albums/m...pssty0f17j.jpg Plan is to take the parts to a wheel and tyre shop to get the toe and allingnment set at the same time as fitting these parts. Brakes still need to be bled, and because I do not know what type of brake fluid is in there, draining the system as well, is on the cards too. That way ensuring the brake fluid is both fresh as well as uniform. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Courier delivered this yesterday.
So tell me what and where it is headed. http://i294.photobucket.com/albums/m...psmakms1ck.jpg One step closer. I stopped by at a local wheel and tyre shop yesterday to find out if they could set the front wheels up for me. Yes, but I needed to fit the steering parts myself, due to corporate policy etc. Which is fine. Priced at a reasonable £30.00 after a call to a different company got me a quote for £50.00 May just go down on Sunday if I can get the brakes sorted, but working day job all week and all of Saturday. I thought the road tax ar £225.00 was pretty good too. http://i294.photobucket.com/albums/m...pszewiqz8z.png And finally, in these days of politically correct and then the rest..... This Made me laugh. http://i294.photobucket.com/albums/m...pspqczo3kz.jpg |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Remember the stainless steel wheel trims I bought last week?
Forgot to try them on, but also the day job has kept me busy. So tonight after work, in the dark I went and tried to fit one on the truck. I have to say..... I love it, the result is even better than I had anticipated. http://i294.photobucket.com/albums/m...psmak4vl1e.jpg I will be honest. After the trim ring fitting, I decided screw dinner, it will be there later (left overs from yesterday) more fun down at the garage. Chilly down there. http://i294.photobucket.com/albums/m...psikwvelth.jpg But I decided to get on and strip down the front steering parts and replace them too as it needs to be done before I take the truck in to get the wheel alignment, Toe etc set. Once I had the truck up in the air, it was big hammer, spanner, sockets and some crawling around. Harley was constantly under my feet too, weird cat, but good company. http://i294.photobucket.com/albums/m...psnkakb1kg.jpg The two ends weirdly have different sized nuts. There has to be a reason of course http://i294.photobucket.com/albums/m...pszx7uy0oj.jpg So first the one side, then the other. Harley was laying next to me while i was undoing things. http://i294.photobucket.com/albums/m...psfzkxw4tb.jpg Finally, all the nuts, bolts and whatever else was tightened and torqued up. Very happy with the outcomes. http://i294.photobucket.com/albums/m...psmjlwttrj.jpg I checked all the four corner wheel arch heights and it seems the rear had come down by 10mm after the front end rebuild. Now with all the parts replaced, I am hoping for many years of good, easy motoring in the Blazer. Just added up the costs of all I have done to it so far and it totals up to £630.00 but it was the right thing to do. Still not convinced about this truck, whether it’s really not a Project, but it certainly has done me too. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Message from Dennis this morning when I got up.
Not good news. Seems snow overnight in St Louis. http://i294.photobucket.com/albums/m...psaupgoher.jpg Anyway, my day was loads of admin, then run around trying to find out some inside info from clients, never easy, but succeeded. Skype video conference with boss at 3pm booked for an hour. On the way home, I called Stuart the neighbor to see if he was available after my video thing to help me get the brakes pumped while I drained them, of course he said yes. So we got onto it by 4pm and by 5pm after a good chat, we were done and he headed home. Brakes bled, means Sunday could be wheel alignment. Then drive, fun and MOT . http://i294.photobucket.com/albums/m...pskqgqakuh.jpg Failing light meant no decent photos of stance and arch height. http://i294.photobucket.com/albums/m...psvhjrvkbk.jpg Also found a set of Bootfair valve caps that will go on once the new stainless trims get fitted. http://i294.photobucket.com/albums/m...psin7m9n3g.jpg While down there I realised that I do need some hubcaps if I can find a set. Eyes open. http://i294.photobucket.com/albums/m...psgln3xkcq.jpg You know what they say about idle hands....? Well..... 2.5” single exhaust pipe from behind the cast iron headers. http://i294.photobucket.com/albums/m...psggjwqbf0.jpg So I started to look around on EBay I was under the impession that that I had one in the garage, but must have given it away years ago. http://i294.photobucket.com/albums/m...psdp1gt8et.jpg http://i294.photobucket.com/albums/m...psxr1sjr24.jpg So, if you have a full set of top hat caps, of know of a set somewhere in some for sale or dontation somewhere, please let me know. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Saturday.....
On the High Speed train to St Pancras station in London, then a black cab to St Barts Hospital for the day. Working to get a day in lieu later when I need to take the Blazer for its MOT. However, last night, sitting with Aaron Kauffman’s Shifting Gears on in the background and surfing the web, I had a Rum and Pepsi, later I followed it with a 500ml Mountain Dew, fully aware of the caffeine in there....... Not a clever move. Woke at 02.30 and then tossed and turned. http://i294.photobucket.com/albums/m...ps8k2dybg4.jpg But....... Sometimes waking to an invoice is actually quite pleasant. Add shipping and we have a dropped asss on the Blazer. http://i294.photobucket.com/albums/m...pssqfub5ct.jpg Instructions include the use of a Grinder and cutting disc. http://i294.photobucket.com/albums/m...pssxjhii9k.jpg To get these babies fitted. http://i294.photobucket.com/albums/m...psjlpxyafs.jpg http://i294.photobucket.com/albums/m...pss62yufs6.jpg Another bit of fun to add to this truck. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Been a long day.
Slept an hour in the chair downstairs, care of the Captain. Anyway, put the word out that I was looking for a set of centre caps for the Rallye wheels on the Blazer. Got a reply from Glasgow in Scotland. http://i294.photobucket.com/albums/m...psez3gxa5v.jpg These. http://i294.photobucket.com/albums/m...psorfz36ms.jpg To go with these. http://i294.photobucket.com/albums/m...psmak4vl1e.jpg In other news....... Dennis posted out the drop shackles today. So soon we may see more action. Working in London today, all the streets were blocked so I did a good walk after the cab driver gave up. http://i294.photobucket.com/albums/m...psjw9em20u.jpg But it allowed me to see loads of beauty in the city I dislike so. http://i294.photobucket.com/albums/m...ps0iu89dbi.jpg Late afternoon after we left the meeting and I got back to St Pancas for theb35 minute high speed trip back to my Station n, the weather had turned decidedly worse. http://i294.photobucket.com/albums/m...psvanjggxc.jpg http://i294.photobucket.com/albums/m...ps0uoyvggl.jpg I will be honest, I had planned on taking the Blazer for a drive tonight but it will have to wait for tomorrow. Armistice day 11/11,18 Looking forward to driving this truck and feeling it’s new constitution |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Yup
Its not a project. Becoming more than that now. Becoming fun, and a lot of it. Looking to see if there are any modern estates, 4x4’s like Pajero, Shogun, Discovery etc that has a set of roofracks I can rob off it. This is where it could be headed. http://i294.photobucket.com/albums/m...ssrgcfwun.jpeg Any advice or pointers appreciated. Thank you. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Sunday.
Remembrance Sunday, and to me a serious business. Having served too, I do remember those no longer with us, those who,paid the greatest price so that I can live a good and easy life. Because I worked yesterday my weekend was a bit short, so I had lots to do. Starting with another bad nights sleep, I ended up doing loads today. Bringing the truck up from the garage, the plan was to tint the windows and then head for town, but they were more complex as you need a five armed monkey to hold, stretch and apply the film when there is a breeze out like today. http://i294.photobucket.com/albums/m...psw60lj65t.jpg Cleaning the inside window glass, I realised the whole thing needed a wash. http://i294.photobucket.com/albums/m...psxt3bp1rk.jpg I also found evidence of a previous tint in the rear. http://i294.photobucket.com/albums/m...ps0u36vb22.jpg Quick wash, still took quite a while. http://i294.photobucket.com/albums/m...psom8uc1gm.jpg http://i294.photobucket.com/albums/m...psadbkiqu8.jpg Another observation. I need to find a replacement headlight, this one works but the milky glass does not appeal to me. http://i294.photobucket.com/albums/m...pspntbhd4s.jpg What it should look like, other side. http://i294.photobucket.com/albums/m...ps6hshtyzw.jpg Once the car was washed, I took it down the tight drive. http://i294.photobucket.com/albums/m...psezrwq7rr.jpg And first time it was out of the property since I bought it and Lee delivered it. Confrontation? http://i294.photobucket.com/albums/m...psywuvr2sq.jpg I was headed up to the farm to get a few decent photos...... We like a nice photo, don’t we? Before alignment time. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
So I went up to the farm to see if I could get some nice pics that justified the truck for what it really is.
Not as bad as I have made it out. I do not think this truck has ever been in an accident and all the panels seem to be straighter than one could expect from a 40year old. http://i294.photobucket.com/albums/m...psisnqprwa.jpg http://i294.photobucket.com/albums/m...ps9xkrvalj.jpg I had removed the license plate whe. I started to look at getting the Towbar made up. It was held in place by two rusty panel screws, one broke off in the backing plate, the other came out, so I just taped it in the rear window. http://i294.photobucket.com/albums/m...psczklte2y.jpg Thames river in the background. http://i294.photobucket.com/albums/m...ps0qoekpbw.jpg From the farm I headed toward Rochester...... Of course stopping in for some fuel. http://i294.photobucket.com/albums/m...pstqfkeskx.jpg Then a drive down the bypass motorway to get a good feel for the handling. It weaved lightly,and drew to the right all the time. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
http://67-72chevytrucks.com/vboard/s...d.php?t=419251 This mammoth thread has plenty of tech for the front end being dialed in from mild to wild. Also a good amount for rear leaf spring improvement in ride & handling.
|
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Quote:
Thank you for sharing. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
So after filling the galactic sized tank with enough fuel to run 10 Smart cars for a month, I headed down to Strood to get the wheels aligned but typically the original £30.00 offer was not available as they did not have the details for the Chevy Blazer in their system.
They not so friendly guy behind the counter suggested I go to another shop. So off to STS I went. Friendly, knowledgeable guys, relieved me of £65.00 and sent me off with a truck that felt completely different to the one I had taken there. WIN !! http://i294.photobucket.com/albums/m...ps71gyj2wx.jpg http://i294.photobucket.com/albums/m...psy5asijhg.jpg The results spoke for themselves. http://i294.photobucket.com/albums/m...psf8ljbcei.jpg From there I went driving around, looking for another decent photo venue. http://i294.photobucket.com/albums/m...psqfo4olj8.jpg http://i294.photobucket.com/albums/m...pss8y6vphs.jpg Eventually got home with a silly grin on my face. The truck is Happy at 70mph on the motorway. Brakes work beautifully 30 miles test drive, worked for me. Reversed down the tight drive, planning to give the window tinting another go. Realised the garden has grown a lot over the last few years. http://i294.photobucket.com/albums/m...pselvmwd1f.jpg So trimmed that lot back and raked up all the dead winter leaves..... http://i294.photobucket.com/albums/m...psw9img62o.jpg With the weather constantly changing between rain and not raining I decided to open the rear tailgate and service the window raiser mechanism http://i294.photobucket.com/albums/m...psggzao4st.jpg http://i294.photobucket.com/albums/m...ps0hanzn1f.jpg Greased all the gears, sprayed the invisible parts with STS and then tested and shut it all up again, happy. http://i294.photobucket.com/albums/m...pso9nw4rug.jpg And them thought I would give the window tinting another go....... Big mistake, again. So I left it alone. http://i294.photobucket.com/albums/m...psvpmkyrz8.jpg So that ended up a great day for me. Only the MOT left to go do when I get my day in lieu back. Then lots of fun, random things after that. I hope. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
The rebuilding of the rear leaf spring pack is straight foreword/easy. You may consider it when you add the rear shackle mount to lower the rear then. Congratulations on finding a good, competent shop in dealing with your need's. The 2WD Blazers are not popular in the states it seems. I dig them like all rough-to-nice.
|
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Quote:
I do plane on adding new rear spring bushes to the rebuild, just need to wait and see what is in the shackle kit, as I do not think there is an upper leaf spring bush, so ai May have to order both. Finding the shop was a bit of luck, I was not impressed with the $80.00 charge, but the moment I drove it, the work was worth the price. Over here the K5’s are popular too, but I like different, so a 2WD is my flavour. Also I have no use for 4WD. |
Re: GRIZZ’s ‘79 - 2WD BLAZER Challenge over in London, England. “~It’s not a Project
Almost up to date now.
Funny how the little things, like looking out and seeing this lump,outside now makes me smile. http://i294.photobucket.com/albums/m...pskgmbzbft.jpg I was asked on another forum about English property sizes and access and how I got the truck into the garage. I guess TIGHT FIT is not an understatement. Reversing the Blazer down the side of the house gets the best results. I actually have to swing it around every concrete post as the mirrors are too wide to just go straight down. Makes me chuckle at the madness every time I do it http://i294.photobucket.com/albums/m...psedzgkivg.jpg Prozac the Berlingo is an easy loose fit. http://i294.photobucket.com/albums/m...psfrslqewi.jpg Mate Darren of Unit Engineering had a bunch of random items in his £5.00 bargain bin on FB this week, so I bought the stainless Stormtrooper for the Blazer. He will also later cut any other design on request and does all sorts of engineering and batch engineering manufacturing Still need to figure out where it will go. http://i294.photobucket.com/albums/m...pshuw5gmui.jpg |
All times are GMT -4. The time now is 06:36 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com