Re: 68 aka "Chained in Porterbuilt Prison"
Where can I get that evaporust ?
Posted via Mobile Device |
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
Posted via Mobile Device |
Re: 68 aka "Chained in Porterbuilt Prison"
Posted via Mobile Device
|
Re: 68 aka "Chained in Porterbuilt Prison"
1 Attachment(s)
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
Awesome fab work I love the dimples! The fender brace part turned out very nice and LOVE the rad support.
|
Re: 68 aka "Chained in Porterbuilt Prison"
2 Attachment(s)
few more pics.....threaded the entropy shroud for the topper...little closer look at corner brackets...these dimples were made without press..16 guage metal...with 18v dewalt impact..and 3/8's bolt thru center of die...super nice pieces...never used them before but i'm a fan now...jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
Looks awesome!! Where did you get the dimple dies? Not that I really need them but I love to own tools:lol: I went back and looked at your dash and I really think it is the nicest C10 dashes I have seen. Where are you putting your radio? I am going through that decision right now. I really would like to find a remote controled unit I could mount under the dash to to keep it clean.
I am also in the defroster vent delima. Looks like you have the billet ones from Vintage Air. Those seem to be the best solution for the dash. I wished someone made something more flush fitting. |
Re: 68 aka "Chained in Porterbuilt Prison"
1 Attachment(s)
Quote:
dies...... http://cgi.ebay.com/ws/eBayISAPI.dll...m=160858744386 that's a Doc's Kustom piece...about the cleanest i could find....thought about welding in a flush grid...just didn't take the time....jim |
Re: 68 aka "Chained in Porterbuilt Prison"
2 Attachment(s)
Welding up cowl....what a pain in the azz!!! Mounted overflow...in this shot u can see when u panel these cores how much angle compared to radiator...and i took some of the rearward angle out of radiator! With TUBZ in not near as obvious....jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
the more I see the better it gets
|
Re: 68 aka "Chained in Porterbuilt Prison"
everything looks KILLER !
|
Re: 68 aka "Chained in Porterbuilt Prison"
Cool!! Love the dimples
Posted via Mobile Device |
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
Posted via Mobile Device |
Re: 68 aka "Chained in Porterbuilt Prison"
Man, everything looks great!
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
Like the dimples sure looks good
|
Re: 68 aka "Chained in Porterbuilt Prison"
The truck looking great! and the dimples look awesome!
|
Re: 68 aka "Chained in Porterbuilt Prison"
I modified my radiator core support also so that I could fit electric fans in there and the question that I had that I hope you can answer for us both is does it jack with the hood closing or not? Like is there any interference with the hood anywhere when you mod it like that? Looking great
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
You will have no clearance issues !
Posted via Mobile Device |
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
R/ |
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
Quote:
|
Re: 68 aka "Chained in Porterbuilt Prison"
1 Attachment(s)
Here's the pic ....rounded out around neck....also trimmed the edge holding the upper rubber..it was touching top of radiator....look close under that pair of pliers and u can see that 3/16" rolled edge effect...plug welded those panels below...that small edge of panel facing radiator will be welded ...will all be cleaned up and probably body color...jim
|
Re: 68 aka "Chained in Porterbuilt Prison"
Very cool work on the fender braces and rad support. Im looking at doing something very similar... but that means I have to work on my truck! lol
|
All times are GMT -4. The time now is 11:02 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com