![]() |
Re: Frankentruck
Quote:
Quote:
|
Re: Frankentruck
Keep it up and I know who will be doing patches on Ma Bell .
|
Re: Frankentruck
Quote:
|
Re: Frankentruck
You can use my shop anytime you like , I dont need to be there .
|
Re: Frankentruck
Quote:
|
Re: Frankentruck
1 Attachment(s)
I got the engine bay side of both inner fenders painted today. Fought through the rain, but was able to get it done.
They are inside the garage drying |
Re: Frankentruck
1 Attachment(s)
Will I get the truck back together for the Georgia C10 Club meet on Saturday? I sure hope so, but it's looking promising.
On another note, so far, the new TriPlus core support from AMD has lined up real nice and I have not had to whaller out a single bolt hole yet. All the other sheet metal that will be going on is original GM stuff :metal: |
Re: Frankentruck
2 Attachment(s)
Looking like a truck again! Got everything pretty much buttoned up, just a couple bolts left for in the morning. Should be able to drive it to the Georgia C10 Club meet tomorrow!
I replaced the grille support panel that was busted and rusted with a decent, rust free one. I also got my fan shroud on, but I will need a shorter fan spacer |
Re: Frankentruck
Looks great Christian
|
Re: Frankentruck
Quote:
|
Re: Frankentruck
5 Attachment(s)
Today was a good day.
Met up with MikeN to get a fan and fan clutch from his 65 Impala. It ended up fitting almost perfectly with my new shroud. The old fan was too far into the shroud once I moved the radiator to the correct, v8 location and installed the shroud. Thanks again Mike! After getting the fan, I went and picked up a 60 hood. It's got the usual rust, but I think I can fix it eventually lol. It's one of those things that I just couldn't pass up. Yesterday, I got a switch so that I could completely turn off power to the overdrive system whenever I want to drive it in lockout. I used on of the holes already in the bottom of the dash, so I didn't have to drill any extra holes. I plan to pull a few trailers, so I probably won't be using the overdrive when I do that. Happy 4th! :metal::flag: |
Re: Frankentruck
FrankenTruck is still one of my all time favorites simply because you are building and repairing it as you go yourself . Christian , that truck is like you , Awesome .
|
Re: Frankentruck
Quote:
|
Re: Frankentruck
1 Attachment(s)
Happy 4th y'all! :flag:
I like to celebrate by driving Frankentruck around and eating some good food with friends. Also, it's been 5 years now since I've had Frankentruck. Hopefully many more to come :metal: |
Re: Frankentruck
Quote:
|
Re: Frankentruck
Quote:
|
Re: Frankentruck
Quote:
|
Re: Frankentruck
2 Attachment(s)
Mmmm, that cross pin lock bolt shouldn't be like that...
I don't think that gap should've been there on the pinion seal either. New axle bearings and seals and a new pinion seal went in today. Just gotta find a new bolt now. My good friend Levi helped out a ton today and I got to use his fancy mechanic tools lol |
Re: Frankentruck
1 Attachment(s)
I called up some local dealerships this morning, but had to drive an hour to find the correct part. Bought three of them since it is a discontinued part now. It was still cheaper than buying the one from Summit Racing, and I got extras. Put everything back together and went for a test drive. I think I fixed all the leaks, but it was dark when I got back, and I was sad. Everything was going great until I heard a metallic smack. I pulled over and started looking underneath the rear of the truck. There's now a visible gap between the axle pads and trailing arms on both sides. Apparently my axle is trying to leave the truck... :no: Fix one thing and another breaks :banghead:
My test drive consisted of stopping by Flashed's place and messing with the Quadrajet on his 79 square. I'm thinking the carb needs a rebuild, but I'm not sure. Time to do some more research lol |
Re: Frankentruck
At least that should be a simple fix of just tightening the ubolts
|
Re: Frankentruck
Quote:
|
Re: Frankentruck
Quote:
Do you remember what fan you used? |
Re: Frankentruck
Quote:
|
Re: Frankentruck
2 Attachment(s)
One of the driver's side brake shoes had a crack in it, so I was able to get that warrantied and replaced both sides today.
After that was done, I took the rattle gun and buzzed off the u bolt nuts. Looks like the u bolts came loose many years ago, were tightened back up, and they worked loose again. I'll be getting new u bolts in the morning |
Re: Frankentruck
3 Attachment(s)
Got some new u bolts today. I don't have a torque wrench that goes up to 230 ft lbs, but my friend brought his that goes up to 250 ft lbs. I went to get it this evening and will be installing the new bolts in the morning.
After getting the u bolts, the AC compressor clutch went out on my Dakota. Not sure what I'm going to do there. I spent the rest of the morning and afternoon cleaning up and painting some of the under hood parts that I had not painted when I took the front end apart. Had to use the shade tree paint booth to get it done :lol: |
All times are GMT -4. The time now is 11:12 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com