Re: What did you do to your truck today part IV
2 Attachment(s)
Not today but yesterday. I´m going to test-fit some sheet-metal on my -62 C10 Panel before welding and straighten the side of the truck. 1/4" bondo.
|
Re: What did you do to your truck today part IV
3 Attachment(s)
We got the rear window opening cut out to match the inside panel. It looks like a whole new truck. I cut out a section of the front panel to start reparing.
|
Re: What did you do to your truck today part IV
1 Attachment(s)
I took the gas tank out.Attachment 1764764
|
Re: What did you do to your truck today part IV
1 Attachment(s)
Test fit my china repo door. Getting ready to cut out the rust on the inter, outer rockers.Attachment 1765139
|
Re: What did you do to your truck today part IV
2 Attachment(s)
Here is the inner basecoted and outer sheetmetal welded, so that is what I have been done today. I hope that I can begin whit the corner tomorrow.
|
Re: What did you do to your truck today part IV
I installed the new NOS distributor I got from forum member chevy2inreno on the 250 6-banger on Sunday. Checked initial timing on the old one, was set at about 8 degrees BTDC. Spec is 4 BTDC, but I've heard from old GM mechanics that timing should be advanced to just before pinging starts on regular gas with this motor.
So installed the new distributor and set initial timing at the same 8 BTDC. Drove the truck to work today- HOLY CRAP! what a difference. Way more acceleration, should have done this a long time ago, but I though the old distributor was OK. Think I've got the Rochester B and the spark timing dialed in pretty good now. :metal: |
Re: What did you do to your truck today part IV
1 Attachment(s)
Welded up the hole.
|
Re: What did you do to your truck today part IV
3 Attachment(s)
Got the hood back on with new updated hinges. Now lots of wiring to be done.
|
Re: What did you do to your truck today part IV
4 Attachment(s)
Pulled the engine out of Frankentruck
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
3 Attachment(s)
Fixed the middle windshield area. Cut out my passenger side a piller. Roof had rust so i made a piece and welded it in.
|
Re: What did you do to your truck today part IV
1 Attachment(s)
Finished the grille for my 62
|
Re: What did you do to your truck today part IV
1 Attachment(s)
Took the inter fender off.Attachment 1767318
|
Re: What did you do to your truck today part IV
2 Attachment(s)
|
Re: What did you do to your truck today part IV
4 Attachment(s)
Replaced right side mirror bracket with NOS GM mirror I found on Ebay. Holes were there, somebody must have damaged original and replaced with aftermarket bracket. Mirror was the original GM mirror. Looks better. Cleaned out drip rail and put new seam sealer in.
|
Re: What did you do to your truck today part IV
3 Attachment(s)
Finished my Dolphin Gauge insert. Dead on with my GPS once calibrated.
|
Re: What did you do to your truck today part IV
2 Attachment(s)
Ruh Rho!
|
Re: What did you do to your truck today part IV
Oh well, I tried...
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
2 Attachment(s)
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Pulled my gauge cluster to be sent to redlineg.com next week. Going to add vacuum gauge, tachometer and convert the amp gauge to a volt gauge and calibrate the rest.
Also Ordered a rebuilt Saginaw 3-speed overdrive transmission. |
Re: What did you do to your truck today part IV
1 Attachment(s)
Took apart the th400 to beef it up in preparation of 500+ lb ft of torque.
|
Re: What did you do to your truck today part IV
You fellas are an inspiration!!
|
All times are GMT -4. The time now is 11:52 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com