|
Re: 55 Wagon Progress
Moving on to closing up the ends of the outer seat riser... Quite a bit of stretch to get this corner to match up to the seat riser...
http://i5.photobucket.com/albums/y16...5/IMG_2270.jpg http://i5.photobucket.com/albums/y16...5/IMG_2271.jpg http://i5.photobucket.com/albums/y16...5/IMG_2272.jpg http://i5.photobucket.com/albums/y16...5/IMG_2276.jpg http://i5.photobucket.com/albums/y16...5/IMG_2277.jpg http://i5.photobucket.com/albums/y16...5/IMG_2278.jpg https://www.youtube.com/watch?v=wzorB_hwLZM Then the corner was Tig welded in place and another test fit with the bucket seat.. https://www.youtube.com/watch?v=kf-X5eHc5bE |
Re: 55 Wagon Progress
Well, let's back up and punt one more time. The owner of the 55 stopped by about a week ago and sat in the mocked up bucket seat. She said it sat too high, so our version 2 seat brackets were out. Cutting the floor pan was over-ruled (for recessing the brackets) so we opted for a 14 gauge flat seat pan directly on top of the floor, which also gave us a shape we could eliminate the "step" in the floor.
http://i5.photobucket.com/albums/y16...5/IMG_2292.jpg http://i5.photobucket.com/albums/y16...5/IMG_2290.jpg http://i5.photobucket.com/albums/y16...5/IMG_2293.jpg https://www.youtube.com/watch?v=JYklSvTtTTQ https://www.youtube.com/watch?v=CfWqQyOeXJo Next is to add the wedges to the rear ramp for attaching the rear of the track slides... |
Re: 55 Wagon Progress
The youtube videos are a nice touch. Thanks!
|
Re: 55 Wagon Progress
Thanks!
Final design on the bucket seat brackets... and owner approved today as well. One down, one to go.. This is made from 14 gauge cold rolled steel and puts the seat about as low as we can go without cutting the floor pan.. Video of the seat bracket: https://youtu.be/YF7LOe7eLTQ Seat test fitted: http://i5.photobucket.com/albums/y16...5/IMG_2320.jpg http://i5.photobucket.com/albums/y16...5/IMG_2321.jpg |
Re: 55 Wagon Progress
Don't think I showed this on the other side, but here's how we find the center of the bend for dimensioning the seat bracket..
http://i5.photobucket.com/albums/y16...5/IMG_2360.jpg Bent up and a test fit... http://i5.photobucket.com/albums/y16...5/IMG_2361.jpg Relief cuts made for the next fold..... http://i5.photobucket.com/albums/y16...5/IMG_2390.jpg |
Re: 55 Wagon Progress
.....then rolled through the bead roller
http://i5.photobucket.com/albums/y16...5/IMG_2253.jpg and then the brake is used to fold the outer flange. Here, all welded in place... http://i5.photobucket.com/albums/y16...5/IMG_2418.jpg The front hole pattern is laid out to match the drivers bracket, and then some perpendicular lines laid out for locating the rear risers... http://i5.photobucket.com/albums/y16...5/IMG_2419.jpg http://i5.photobucket.com/albums/y16...5/IMG_2420.jpg http://i5.photobucket.com/albums/y16...5/IMG_2421.jpg http://i5.photobucket.com/albums/y16...5/IMG_2422.jpg |
Re: 55 Wagon Progress
Got a new apprentice that started this past Saturday.. Her mom even thought it was a good idea!
http://i5.photobucket.com/albums/y16...5/IMG_2425.jpg http://i5.photobucket.com/albums/y16...5/IMG_2430.jpg She's getting the driver's seat bracket all prepped for SPI epoxy primer, while I worked on finishing the passenger bracket.. http://i5.photobucket.com/albums/y16...5/IMG_2426.jpg http://i5.photobucket.com/albums/y16...5/IMG_2428.jpg http://i5.photobucket.com/albums/y16...5/IMG_2432.jpg http://i5.photobucket.com/albums/y16...5/IMG_2434.jpg |
Re: 55 Wagon Progress
Great seeing them young ones interested.
|
Re: 55 Wagon Progress
What kind of media are you using in your blast cabinet?
|
Re: 55 Wagon Progress
http://i5.photobucket.com/albums/y16...8770229276.jpg
It's actually made for water jet machines, get it from a local machine shop.. Also use the 80 grit garnet that tractor supply carries. |
Re: 55 Wagon Progress
Sometimes you just need to screw off in the shop all day. So while the new hire continued with media blasting, I turned my attention to this "new" hoop for the Watervliet planishing hammer that just showed up.. This square version is somewhat rare, ie: hard to find, but I had a particular location in mind..
http://i5.photobucket.com/albums/y16...pt/IMG_001.jpg The Baileigh power hammer has some threaded holes on the left side for their own version of a planishing hammer mount, but I just didn't have the funds laying around for their version. So lets see what we can do with Old Faithful... http://i5.photobucket.com/albums/y16...pt/IMG_002.jpg http://i5.photobucket.com/albums/y16...pt/IMG_004.jpg Drum sander does wonders in pipe fitment, and it sure was easier to TIG with a nice tight fit... http://i5.photobucket.com/albums/y16...pt/IMG_005.jpg http://i5.photobucket.com/albums/y16...pt/IMG_007.jpg http://i5.photobucket.com/albums/y16...pt/IMG_009.jpg http://i5.photobucket.com/albums/y16...pt/IMG_011.jpg http://i5.photobucket.com/albums/y16...pt/IMG_012.jpg http://i5.photobucket.com/albums/y16...pt/IMG_014.jpg All we need now is paint and a pedal.. https://www.youtube.com/watch?v=_evAUjqr-5Q . |
Re: 55 Wagon Progress
Getting down to the nitty gritty on the seat brackets, number two is all but done, need to weld in three hex nuts and touch up some media blasting. Hoping for good weather this weekend so we can spray some epoxy primer on them and get these installed...
http://i5.photobucket.com/albums/y16...5/IMG_2519.jpg http://i5.photobucket.com/albums/y16...5/IMG_2520.jpg http://i5.photobucket.com/albums/y16...5/IMG_2528.jpg http://i5.photobucket.com/albums/y16...5/IMG_2526.jpg And the last two pipe clamps came in at Napa (installed with lock nuts), so we can now throw some air to the planishing hammer and try out the new fixture.. http://i5.photobucket.com/albums/y16...pt/IMG_016.jpg |
Re: 55 Wagon Progress
This weekend we got the three hex nuts welded underneath seat bracket number two, fourth hole is a bolt through......
http://i5.photobucket.com/albums/y16...5/IMG_2532.jpg http://i5.photobucket.com/albums/y16...5/IMG_2533.jpg http://i5.photobucket.com/albums/y16...5/IMG_2535.jpg 1/4" tall spacers fabricated to make the seat tracks level, then tacked in place on the front holes.. http://i5.photobucket.com/albums/y16...5/IMG_2559.jpg http://i5.photobucket.com/albums/y16...5/IMG_2560.jpg http://i5.photobucket.com/albums/y16...5/IMG_2563.jpg Prepped and hung up for epoxy primer... http://i5.photobucket.com/albums/y16...5/IMG_2565.jpg OEM seat bracket holes in the floor pans open to the inside of floor crossmembers. Rather than weld them closed and warp the floor pan, we opted for these fancy hole plugs. http://i5.photobucket.com/albums/y16...5/IMG_2568.jpg http://i5.photobucket.com/albums/y16...5/IMG_2569.jpg http://i5.photobucket.com/albums/y16...5/IMG_2570.jpg SPI epoxy primer applied... http://i5.photobucket.com/albums/y16...5/IMG_2573.jpg http://i5.photobucket.com/albums/y16...5/IMG_2579.jpg When it's 39* outside and the paint booth is sucking the heat out of the building, this is how you keep the temps up to a balmy 75* in the paint booth.. http://i5.photobucket.com/albums/y16...5/IMG_2575.jpg We'll let the seat brackets cure for a few days and then get started on plug welding them in place.. |
Re: 55 Wagon Progress
Got started on drilling plug weld holes this evening, here laying out the hole patterns to align with the floor crossmember where possible...
http://i5.photobucket.com/albums/y16...5/IMG_2590.jpg Once drilled to match our piloted burnishing brush, the paint surrounding the plug weld gets cleaned to prevent weld contamination.. https://www.youtube.com/watch?v=ELG55mmG2I0 http://i5.photobucket.com/albums/y16...5/IMG_2593.jpg |
Re: 55 Wagon Progress
Robert, nice job, fits verywell...Jim
|
Re: 55 Wagon Progress
Looks really nice, you do great work.
I appreciate your posts and videos. It gives some interesting insights on how the job should be done correctly. |
Re: 55 Wagon Progress
So perfect only the knowing eye 'might' catch it.
Job well done Sir. |
Re: 55 Wagon Progress
Fantastic work as always!
|
Re: 55 Wagon Progress
Yes, very nice work. Where did the piloted burnishing brush come from?
|
Re: 55 Wagon Progress
They came from McMaster Carr. Look up piloted end brushes. They have them in various pilot sizes and either 1/2 or 3/4 diam, we used 1/2..
Thanks for the comments guys! Posted via Mobile Device |
Re: 55 Wagon Progress
With the 55's rear seat bottom narrowed to fit the wheel tubs.....
http://i5.photobucket.com/albums/y16...5/IMG_2641.jpg ....time to do the same for the seat back. First to blow it apart.... http://i5.photobucket.com/albums/y16...5/IMG_2713.jpg This had a multiple fold down, arm rest in the middle, non 55 looking arrangement. The arm rest will be first to go, and we'll attach the fold down sections together.. The frame is sectioned in the middle, a tube driven inside, and TIG welded around the perimeter.. http://i5.photobucket.com/albums/y16...5/IMG_2714.jpg http://i5.photobucket.com/albums/y16...5/IMG_2715.jpg Then the seat innards are trimmed accordingly to make a one piece back.. http://i5.photobucket.com/albums/y16...5/IMG_2716.jpg http://i5.photobucket.com/albums/y16...5/IMG_2718.jpg Then some 14 gauge strips are cut out to join the two sections together.. http://i5.photobucket.com/albums/y16...5/IMG_2719.jpg http://i5.photobucket.com/albums/y16...5/IMG_2720.jpg http://i5.photobucket.com/albums/y16...5/IMG_2721.jpg http://i5.photobucket.com/albums/y16...5/IMG_2724.jpg http://i5.photobucket.com/albums/y16...5/IMG_2725.jpg http://i5.photobucket.com/albums/y16...5/IMG_2727.jpg http://i5.photobucket.com/albums/y16...5/IMG_2726.jpg http://i5.photobucket.com/albums/y16...5/IMG_2728.jpg http://i5.photobucket.com/albums/y16...5/IMG_2730.jpg That should work, tomorrow we'll work on the new pivot brackets.. |
Re: 55 Wagon Progress
Wow, One heck of a nice job on the back parts of seat...Jim
|
Re: 55 Wagon Progress
Thanks Jim!
In removing the section of foam on the seat back we find the cushion has a wire around the arm rest void. As we are removing the arm rest altogether (when it gets reupholstered) we removed the wire.. http://i5.photobucket.com/albums/y16...5/IMG_2732.jpg http://i5.photobucket.com/albums/y16...5/IMG_2733.jpg http://i5.photobucket.com/albums/y16...5/IMG_2734.jpg http://i5.photobucket.com/albums/y16...5/IMG_2736.jpg The previous pivot for the seats had a tapered pin hex bolt that secured into a hex nut that was welded onto the pivot bracket, which can be seen here: http://i5.photobucket.com/albums/y16...5/IMG_2717.jpg Due to our width constraints, we need to remove all that excess hardware.. So we chose to put the "securing nut" inside the seat, and use a simple pan head allen screw through the 12 gauge bracket.. Here's our Pivot "axle" inside the seat back.. http://i5.photobucket.com/albums/y16...5/IMG_2742.jpg http://i5.photobucket.com/albums/y16...5/IMG_2743.jpg Here's the test fit of our 12 gauge steel pivot bracket. Radius was used on the bends to match the tube. The tube was originally round, and the side uprights were flattened out using the MH19 hammer to buy us some more clearance between wheel tubs.. http://i5.photobucket.com/albums/y16...5/IMG_2744.jpg The bead shown on the bracket was done on the Lennox Nibbler. This should give us a bit of clearance on the edges to help prevent binding of the upholstery. http://i5.photobucket.com/albums/y16...5/IMG_2748.jpg Bead turned out pretty well for 12 gauge steel! Some TIG welding to put the parts together: http://i5.photobucket.com/albums/y16...5/IMG_2749.jpg http://i5.photobucket.com/albums/y16...5/IMG_2750.jpg http://i5.photobucket.com/albums/y16...5/IMG_2752.jpg Video of it in operation: https://www.youtube.com/watch?v=KCcpqbF1jUU One part down, next we'll tackle the brackets to the floor. |
Re: 55 Wagon Progress
Doesn't seem like much got done this weekend, but here's what we did..
Stopped by the local CNC router facility to get some generic guides made for bead detail on the Lennox Nibbler... http://i5.photobucket.com/albums/y16...g/IMG_2763.jpg Also had some blanks cut out over there to the right side. These were to form stops so we can adjust length of our pattern shorter as needed.. http://i5.photobucket.com/albums/y16...g/IMG_2765.jpg http://i5.photobucket.com/albums/y16...g/IMG_2766.jpg It has a snug fit like so: http://i5.photobucket.com/albums/y16...g/IMG_2767.jpg Next was to turn up a new die with less crown than the other we've been using, just to have a different look, a flatter bead.. http://i5.photobucket.com/albums/y16...g/IMG_2770.jpg http://i5.photobucket.com/albums/y16...g/IMG_2773.jpg http://i5.photobucket.com/albums/y16...g/IMG_2775.jpg Setting up for some practice runs... http://i5.photobucket.com/albums/y16...g/IMG_2776.jpg http://i5.photobucket.com/albums/y16...g/IMG_2777.jpg Here's a comparison between the new die and the fuller radius we've been using.. https://www.youtube.com/watch?v=HMi7...ature=youtu.be Thursday night headed over to Virginia, the 52 Chevy tail pan now resided in Fredericksburg and I needed to borrow the original and new one for the Coming Out car show in Charlotte Hall, being held Sunday (today). I had been dragging my feet about even going to the show, but the weather forecast promised beautiful weather, so I went ahead and reserved a vendor spot to show off our fabrication work. Friday night started gathering some samples to take and a put some pictures together for an album.. http://i5.photobucket.com/albums/y16...g/IMG_2792.jpg We still had all the original pieces for the lift gate repair, so that was a good sample.. Set up at the show, I figured parked next to the Ice Cream truck would be easier on my will power than the smell of three BBQ trucks on the other side... http://i5.photobucket.com/albums/y16...g/IMG_2793.jpg http://i5.photobucket.com/albums/y16...26106184_n.jpg http://i5.photobucket.com/albums/y16...g/IMG_2794.jpg Got these pictures right after we set up and before all the crowd showed up. Had a blast, talking metalshaping, rust repair, etc. for most of the day.. Got to meet Duallyjams and look at some of his stainless needing repairs.. The days over, I guess I've got to get back to work now... |
Re: 55 Wagon Progress
Back in the shop this evening, time to make some bolting brackets to hold the seat back frame to the floor..
http://i5.photobucket.com/albums/y16...5/IMG_2799.jpg Locating... http://i5.photobucket.com/albums/y16...5/IMG_2802.jpg http://i5.photobucket.com/albums/y16...5/IMG_2804.jpg Brackets TIG welded on.... http://i5.photobucket.com/albums/y16...5/IMG_2808.jpg This shows it in place, we have about 1/4" clearance at the tight spots.... https://www.youtube.com/watch?v=jB5qRfP7IxY The cleco's were removed and 1/4-20 AVK rivet nuts installed in the floor... Missed that picture... http://i5.photobucket.com/albums/y16...5/IMG_2817.jpg http://i5.photobucket.com/albums/y16...5/IMG_2818.jpg Next will be the top support.... |
Re: 55 Wagon Progress
Now for the top of the seat frame... We started with some 3/8-16 standoffs that are 5/8 diameter, and turn them to 1/2 diameter to fit inside the seat frame tube...
http://i5.photobucket.com/albums/y16...5/IMG_2826.jpg http://i5.photobucket.com/albums/y16...5/IMG_2827.jpg http://i5.photobucket.com/albums/y16...5/IMG_2828.jpg http://i5.photobucket.com/albums/y16...5/IMG_2830.jpg Then holes are drilled in some 1.25 square tubing... http://i5.photobucket.com/albums/y16...5/IMG_2832.jpg http://i5.photobucket.com/albums/y16...5/IMG_2833.jpg Tacked in place and a nut used for added insurance... http://i5.photobucket.com/albums/y16...5/IMG_2837.jpg http://i5.photobucket.com/albums/y16...5/IMG_2836.jpg http://i5.photobucket.com/albums/y16...5/IMG_2839.jpg Seat latches plug welded in place... http://i5.photobucket.com/albums/y16...5/IMG_2844.jpg Side pieces formed.... http://i5.photobucket.com/albums/y16...5/IMG_2842.jpg http://i5.photobucket.com/albums/y16...5/IMG_2856.jpg http://i5.photobucket.com/albums/y16...5/IMG_2847.jpg http://i5.photobucket.com/albums/y16...5/IMG_2848.jpg http://i5.photobucket.com/albums/y16...5/IMG_2849.jpg The side pieces will be trimmed, fitted, and welded to the wheel well... http://i5.photobucket.com/albums/y16...5/IMG_2855.jpg |
Re: 55 Wagon Progress
Robert, you sure make some great pieces, love the attention to detail, that some may never see...Jim
|
Re: 55 Wagon Progress
Thanks Jim!
More work on the seat back bracket... Trimming the side pieces to match the wheel well... http://i5.photobucket.com/albums/y16...5/IMG_2860.jpg Adding welding flange, hammered out of 16 gauge steel.. http://i5.photobucket.com/albums/y16...5/IMG_2864.jpg http://i5.photobucket.com/albums/y16...5/IMG_2866.jpg Test drive.... https://www.youtube.com/watch?v=mpFl01yHvKw Used the Roper Whitney hand punch to make our plug weld holes.. http://i5.photobucket.com/albums/y16...5/IMG_2871.jpg http://i5.photobucket.com/albums/y16...5/IMG_2872.jpg http://i5.photobucket.com/albums/y16...5/IMG_2873.jpg http://i5.photobucket.com/albums/y16...5/IMG_2875.jpg Next we'll close off the back area to contain the amp and bass speaker. |
Re: 55 Wagon Progress
The close up photos really do help! Thanks for posting.
|
Re: 55 Wagon Progress
Impressive work on the seat frame Robert. Appreciate the documented details ... thanks for sharing.
|
Re: 55 Wagon Progress
looking great, as always.
|
Re: 55 Wagon Progress
Wow! I'll be stealing that square tube rounding trick! Nice stuff!
|
Re: 55 Wagon Progress
Thanks for all the comments
Had a short evening in the shop as I was busy packing the neon clock for shipment, so the remainder was spent working on some of the many final details of the rear seat. Here are the factory seat clips to hold the seat bottom in place. http://i5.photobucket.com/albums/y16...5/IMG_3149.jpg http://i5.photobucket.com/albums/y16...5/IMG_3150.jpg In order to use these, let's do a sample and see if we cut a hole in some sheet metal that they'll fit into.. http://i5.photobucket.com/albums/y16...5/IMG_3145.jpg http://i5.photobucket.com/albums/y16...5/IMG_3146.jpg http://i5.photobucket.com/albums/y16...5/IMG_3147.jpg http://i5.photobucket.com/albums/y16...5/IMG_3148.jpg This looks like it will work, we'll get some 18 gauge strips made to hold these that 45 down to the floor, adding some bead details for strength.. http://i5.photobucket.com/albums/y16...5/IMG_3151.jpg |
Re: 55 Wagon Progress
Time for some brackets for the rear seat bottom retainers. Cut out some 19 gauge...
http://i5.photobucket.com/albums/y16...5/IMG_3152.jpg Drilled some holes for an inside radius, and trimmed the corners for the floor pan flange.. http://i5.photobucket.com/albums/y16...5/IMG_3154.jpg Now to fold some flanges on the sides for strength, using the Diacro press brake and a 1/2" thick lower die. By adding some rare earth magnets to the back side to serve as a back stop, we get a perfect 1/4" flange... http://i5.photobucket.com/albums/y16...5/IMG_3155.jpg http://i5.photobucket.com/albums/y16...5/IMG_3156.jpg Then some back and forth between the Erco kick shrinker and the press brake with a narrow die inside the folds.... and we have 45* bends on either end of our brackets... http://i5.photobucket.com/albums/y16...5/IMG_3157.jpg Test fit.... and trimming the retainer hole... http://i5.photobucket.com/albums/y16...5/IMG_3160.jpg http://i5.photobucket.com/albums/y16...5/IMG_3161.jpg http://i5.photobucket.com/albums/y16...5/IMG_3162.jpg http://i5.photobucket.com/albums/y16...5/IMG_3163.jpg http://i5.photobucket.com/albums/y16...5/IMG_3167.jpg http://i5.photobucket.com/albums/y16...5/IMG_3169.jpg |
Re: 55 Wagon Progress
Robert, when you make up your parts, it leaves my without any words to say, just over the top...Jim
|
Re: 55 Wagon Progress
Thanks Jim!
Had our new apprentice started today, while I cut out the hole in the second seat bracket, Mike got started on punching and drilling holes for plug welding the passenger bucket seat bracket... http://i5.photobucket.com/albums/y16...5/IMG_3186.jpg http://i5.photobucket.com/albums/y16...5/IMG_3187.jpg http://i5.photobucket.com/albums/y16...5/IMG_3189.jpg After I got the bracket hole cut out, E media blasted the brackets and added some SPI epoxy using a brush. We mainly wanted to get the bottom side well covered as it will be inaccessible once welded in place.. http://i5.photobucket.com/albums/y16...5/IMG_3190.jpg http://i5.photobucket.com/albums/y16...5/IMG_3199.jpg First coat... http://i5.photobucket.com/albums/y16...5/IMG_3201.jpg Two coats, that should hold us for under a seat... http://i5.photobucket.com/albums/y16...5/IMG_3214.jpg Meanwhile I got out the John Deere rod bender to see if we could make up some anchors for the shoulder belt.. http://i5.photobucket.com/albums/y16...5/IMG_3202.jpg Bent with relief for a 1/2-13 lock nut.. http://i5.photobucket.com/albums/y16...5/IMG_3203.jpg http://i5.photobucket.com/albums/y16...5/IMG_3204.jpg Welded with short bursts and plenty of cooling between to keep the nylon lock intact.. http://i5.photobucket.com/albums/y16...5/IMG_3205.jpg test fit... http://i5.photobucket.com/albums/y16...5/IMG_3208.jpg http://i5.photobucket.com/albums/y16...5/IMG_3209.jpg plug weld holes drilled and welded in place.... http://i5.photobucket.com/albums/y16...5/IMG_3210.jpg http://i5.photobucket.com/albums/y16...5/IMG_3211.jpg Mike finished up plug welding the seat bracket in place... http://i5.photobucket.com/albums/y16...5/IMG_3213.jpg |
Re: 55 Wagon Progress
Had a late start in the shop tonight as I had to go look at a school bus. Yeah, week and a half to go until the end of school.
Looks like something gave the spot mirror a nice push.. http://i5.photobucket.com/albums/y16...0/IMG_3217.jpg http://i5.photobucket.com/albums/y16...0/IMG_3218.jpg The mirror mount looks like it's no longer straight.... http://i5.photobucket.com/albums/y16...0/IMG_3219.jpg OK, so we found it hard to fathom something hitting the mirror that high in the air as the bus was driving into it, so the other possibility was something backed into this one.. A quick search of the buses parked close by revealed this one with some nice shiny metal showing... http://i5.photobucket.com/albums/y16...0/IMG_3220.jpg http://i5.photobucket.com/albums/y16...0/IMG_3221.jpg A quick test drive showed that the mirror didn't vibrate/move around that much so we're going to address this after school is out so this one can still be used for the next couple weeks.. Back at the shop, time to weld in the seat retainer brackets... https://www.youtube.com/watch?v=o9Gj...ature=youtu.be http://i5.photobucket.com/albums/y16...5/IMG_3225.jpg http://i5.photobucket.com/albums/y16...5/IMG_3226.jpg ....and then started the next shoulder harness anchor bracket.... http://i5.photobucket.com/albums/y16...5/IMG_3233.jpg |
Re: 55 Wagon Progress
Pilot hole drilled for the passenger B-Pillar.....
http://i5.photobucket.com/albums/y16...5/IMG_3260.jpg The center point is spring loaded, but they seem to locate better using a pilot hole vs. just a punch... http://i5.photobucket.com/albums/y16...5/IMG_3261.jpg http://i5.photobucket.com/albums/y16...5/IMG_3262.jpg http://i5.photobucket.com/albums/y16...5/IMG_3263.jpg http://i5.photobucket.com/albums/y16...5/IMG_3265.jpg The plug weld holes drilled for the anchor and paint cleaned off in prep for welding.. http://i5.photobucket.com/albums/y16...5/IMG_3273.jpg Apprentice E worked on smoothing off the plug welds from last week.. http://i5.photobucket.com/albums/y16...5/IMG_3266.jpg http://i5.photobucket.com/albums/y16...5/IMG_3271.jpg Welding in the anchor ..... http://i5.photobucket.com/albums/y16...6/IMG_3281.jpg http://i5.photobucket.com/albums/y16...6/IMG_3283.jpg For the lower anchor point, which will hold both the retractor and the lap belt, we used some 14 ga that will be plug welded to the back side of the inner quarter panel just behind the B Pillar.. A 1/2" lock nut is welded to the back side, and a spacer added to the front side to keep the lap belt off the side wall. http://i5.photobucket.com/albums/y16...6/IMG_3297.jpg http://i5.photobucket.com/albums/y16...6/IMG_3298.jpg http://i5.photobucket.com/albums/y16...6/IMG_3284.jpg http://i5.photobucket.com/albums/y16...6/IMG_3285.jpg http://i5.photobucket.com/albums/y16...6/IMG_3287.jpg Or the motion picture version.... Thanks to duallyjam for stepping in for hand model duties in the video... :lol: https://www.youtube.com/watch?v=4na-...ature=youtu.be |
Re: 55 Wagon Progress
Robert, just more nice work...Jim
|
| All times are GMT -4. The time now is 10:54 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com