![]() |
Re: 67-72 Electric speedo
5 Attachment(s)
heres what i got which should be about done...but id like to add a few things to update this. its very time consuming and trial and error but i love the stock finished look. i ran an 80s camaro tach in mine along with the battery gauge guts in the ammeter face...so its a little different.
to get the factory paint off the lens...use Purple Power. it dissolves it VERY easy. be very careful with it and dont let it run to the other printed areas. the green paint i found was at Hobby Lobby. it comes in a little small spray can and it matches VERY well imo. i did 3 coats and it came out nice. i found a 2 wire light socket on amazon that fits pretty good. the base is rubber and does have 4 locking tabs but they fit very nice. if you need to add holes...go just UNDER 5/8" on the hole (i used a drill step bit). all the 5/8 will make it a little loose which is why you see the silicone on one of them. i havent plugged this in to check on the truck yet so cant comment on that yet (truck isnt even running yet) for the fuel gauge...i cut out the stock red lens for the oil and temp lights. instead, i cut the high beam and service engine plastics off the old s10 gauge. cut to fit, then mask off and paint over the words not being used or that will show..then you can glue them to the fuel gauge. gives you a stock-ish way to get a high beam indicator and SES light without drilling into anything |
Re: 67-72 Electric speedo
1 Attachment(s)
|
Re: 67-72 Electric speedo
Looks good! Nice find on the paint, that makes it easier.
|
Re: 67-72 Electric speedo
Eric I wold like to order a set of decals. Do you still have?
|
Re: 67-72 Electric speedo
Bringing this back up as I am interested in a set of the decals also.
|
Re: 67-72 Electric speedo
Quote:
|
Re: 67-72 Electric speedo
like the actual lens? i cut them off the original gauge and glued the ones from the s-10 on. or are you talking how do they light up?
|
Re: 67-72 Electric speedo
Quote:
|
Re: 67-72 Electric speedo
if i remember correctly that red film just pulls right off leaving the holes blank. then, you cut the s10 gauges to fit over them and leave enough to cover the holes. i used super glue to fix them back to the gauges. hope this helps!
|
Re: 67-72 Electric speedo
I am having trouble finding 18–20-gauge sheet metal in my area. Would 22-gauge aluminum work ok?
|
Re: 67-72 Electric speedo
Personally I think .027" thick aluminum is too thin and flimsy.
|
Re: 67-72 Electric speedo
2 Attachment(s)
So I went cheap and bought a small cooking sheet from Wally World for $7. It felt pretty sturdy so I cut my piece out of that. It's aluminum but I think it should work and is easy to work with so far.
|
Re: 67-72 Electric speedo
I'm interested in a couple of sets of the decals/kits.
|
Re: 67-72 Electric speedo
If wanting a stock type check engine light in the dash cluster for an LS swap. Acquire a gas gauge from a 40 series + truck with a diesel engine. IIRC the light up position on bottom right of gauge says "engine" Have a cluster with an air pressure gauge to use in my truck and it has this gas gauge. Been a long time since I have looked at it. Maybe different but was appropriate, just remember I am going to use this as an SES light on my truck.
|
All times are GMT -4. The time now is 05:24 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com