Re: My Dusty 71 GMCe Electruck
 

cutting 1/2" aluminum plate a mil at a time using my FREE Craigslist Craftsman Radial 10" saw with a Diablo 84 tooth non stick blade, yeah baby

thrilling I tell yah!

Craftsman Radial Saw cutting aluminum plate

Re: My Dusty 71 GMCe Electruck
 

Are you going to convert the space in front of the transmotor into a trunk?

Re: My Dusty 71 GMCe Electruck
 

ha ha a Frunk? the wife and I joked about that, how I should mount the batteries under the bed and leave the engine bay completely empty and pull up to car shows like that and pop the hood

Re: My Dusty 71 GMCe Electruck
 

Put some motor mounts on and the radiator, with torn off hoses like it just jumped out of there somewhere along the way.

Re: My Dusty 71 GMCe Electruck
 

that would be hilarious, and stand there all like: "it's the second time this has happened this week, damned LS!"

Re: My Dusty 71 GMCe Electruck
 

The two motors in the original vehicle were working in conjunction? Or on and off at different times? LS motors have a fan relay in the Computer that turns the fans on and off as needed if the motor is working harder. Sometimes only one is working while other times both are working. Is the two motor transmission using the second motor as it needs it but in your arraignment locking them together will any computer reprogramming be necessary?

Re: My Dusty 71 GMCe Electruck
 

no MG1 works as a starter to crank the engine over when staring and then acts as an alternator, there is no traditional starter on the Lexus GS450h, the larger MG2 drives the output shaft, I'll link to an animation gif when I'll get the chance

Re: My Dusty 71 GMCe Electruck
 

Wow that is cool, Alternator and starter in one. I have heard that the giant (three story tall) quarry dump trucks use electric motors for breaking.

Re: My Dusty 71 GMCe Electruck
 

here is the video I promised showing you how the internals work and operate

Lexus Toyota Hybrid Transmission Project 02 : Internals

Re: My Dusty 71 GMCe Electruck
 

I bet, well unfortunately Robert the trans jack adapter sucks big time, it is wrong in so many ways, it is way too tall, and the plate is not long enough (trans falls off of it)

with the truck almost one foot off the ground on blocks, I still could not roll the trans on the jack under it, so here I am literally hoisting up the trans with an engine crane just so I can set it on that stupid jack with the trans adapter on it, PIA PIA major PIA

RECOMMENDATION: Do NOT Buy!

Re: My Dusty 71 GMCe Electruck
 

I got the HF trans jack, worked ok for the 4L60.

Re: My Dusty 71 GMCe Electruck
 

was it this thing?

Re: My Dusty 71 GMCe Electruck
 

No, I splurged for the Pittsburgh $200 one. https://www.harborfreight.com/media/...0/60234_W3.jpg

Re: My Dusty 71 GMCe Electruck
 

I always us a motorcycle jack with blocks of wood under the trans. If its not high enough, I add more blocks while under the truck. I usually have to jack up the truck to get the trans slid under too.

10/10 would not recommend for safety reasons. But I still do it.....

Re: My Dusty 71 GMCe Electruck
 

thanks, yeah that's what I did until I sold my bikes and that lift, like a fool

Re: My Dusty 71 GMCe Electruck
 

so what are the odds one of my existing trans crossmembers will work (couple more on the floor not shown)

Re: My Dusty 71 GMCe Electruck
 

having eliminated the original crossmember that held the Turbo TH350 transomatic in place in the first place, I moved on to one with some drop, using rubber feets from my stock radiator core support (run what you brong!)

Re: My Dusty 71 GMCe Electruck
 

looks like it was made for it

Re: My Dusty 71 GMCe Electruck
 

That fit nice.

I just noticed that the front of the transmission looks like a "fidget". Yeah, keeping grandkids this week....

Re: My Dusty 71 GMCe Electruck
 

mounting the transmission is by far the biggest job on this project

Re: My Dusty 71 GMCe Electruck
 

I'm going with these Jeep like AMAZON motor mounts, figuring if they was strong enuff to hold an engine they ought to hold a transmission

now hang on to your comments as this is all just spit ballin' mock up, and that frame's got more twist and turns than you know it

Re: My Dusty 71 GMCe Electruck
 

so like most I make big plans in my head and then use what I got layin' around the garage

Re: My Dusty 71 GMCe Electruck
 

and if you've followed any of my prior builds, you know I like to class things up with rounded corners, ha ha

Re: My Dusty 71 GMCe Electruck
 

one down three to go

slow is the tempo

Re: My Dusty 71 GMCe Electruck
 

I just trace sum random washer I find laying around

and I do two passes, first one is a ruff cut with a cutoff wheel