Re: What did you do to your truck today part IV
3 Attachment(s)
Updated the cooling system between Christmas and New Year by modifying the fan shroud and changing out the fans to Derale Performance HO 12-in. fans and inset mounting them on the shroud. The temps stay steady now at 180 in stop-go L.A. traffic.
|
Re: What did you do to your truck today part IV
Removed the propeller shaft and am trying to size the yoke to the rear of the 700R.
|
Re: What did you do to your truck today part IV
1 Attachment(s)
Managed to get one side of the suspension back together tonight.
|
Re: What did you do to your truck today part IV
2 Attachment(s)
I removed my old jazz fuel cell in order to make room for my new Boyd tank. And new AN 6 fuel line which will replace my old and too large AN 8 fuel line. I am not sure whether to go with braided stainless an line or stainless hard line. I have had the tank for around 15 years.
|
Re: What did you do to your truck today part IV
what's the difference between a Fuel Cell and a Gas Tank?
|
Re: What did you do to your truck today part IV
About $400.00
|
Re: What did you do to your truck today part IV
Finished removing rear springs and mounts today in order to put new drop springs on my ‘63 longbed. Problem is the bottom bolts on both trailing arms are stuck in there. Heads snapped off while trying to remove them. Looks like tomorrow I will be drilling them out.
Posted via Mobile Device |
Re: What did you do to your truck today part IV
Quote:
Safety fuel cells work just like the gas tank on your street car, but they are designed to prevent spilled fuel in the event of a racing incident. ... Fuel cells generally consist of three parts: The outer can or enclosure, the bladder, and the foam baffling. The fuel cell enclosure is typically made of steel or aluminum. |
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
1. the cell started to warp. The top started sagging inward and the bottom started bowing upward. Yes it was vented, and no, the straps were not to tight. 2. The sending unit did not go all the way to the bottom of the cell, so I never had a correct reading of how much fuel I had left. 3. It came with AN -8 fittings so I ran an -8 fuel line that I think has been causing all sorts of problems sense I installed it. I know I could just replace the line but I needed an excuse to replace the cell with a tank;) 4. I was constantly smelling gas around the cell. If that doesn't convince you, would you like to buy a used jazz fuel cell? |
Re: What did you do to your truck today part IV
1 Attachment(s)
Installed a pol rear sway bar on my 62. The truck is Still up in the air so I have not tried it out yet
|
Re: What did you do to your truck today part IV
That sway-bar reminds me I need shocks on my own Kidney Bouncer.
I've been pulling my hair out trying to figure out why my battery isn't charging and staying away from hammers and large wrenches so I don't do anything I might seriously regret! https://media.tenor.com/images/4b713...d50f/tenor.gif |
Re: What did you do to your truck today part IV
5 Attachment(s)
Todays day of self isolation included installing the new front park lights on the GMC. The counterpart lenses come with rivets which are way bigger than originals, and don't look good installed...5/16" as apposed to the lense openings of 3/16"...you can see the difference in the picture before and after. I filed down the rivets by hand to fit. Drilled out the holes on the housing as the rivet stems are a little larger too. Used an oversized punch with the lenses placed on an anvil to gently splay the hollow core aluminum rivets. Thinking I might try a felt pen or paint to tone down the color of the aluminum heads...Were the originals brass or metal? Problem solved, and they look great
|
Re: What did you do to your truck today part IV
1 Attachment(s)
Got the bumper installed. And mocking up the tailgate.
|
Re: What did you do to your truck today part IV
1 Attachment(s)
More life hours into floors. I'm over it.
|
Re: What did you do to your truck today part IV
2 Attachment(s)
Finally got the Vintage Air installed and charged. I didn't like the look of the plastic box. Built this carpeted cover to reduce the fan noise and attempt to improve the look. It didn't turn out quite like the idea in my head, but it did reduce the noise and is easy to install and remove. The back was left open for air flow, only sides, front, and bottom are covered.
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Took a break from refitting the front suspension to throw on my 'new' Road Runner camper shell.
I'm thinking it needs a chop (lose half the height of the chicken light strip?) but I'll have to see it on its wheels to be sure.. https://live.staticflickr.com/65535/...e0bfe620_h.jpg https://live.staticflickr.com/65535/...eb352af6_h.jpg |
Re: What did you do to your truck today part IV
Did final install (Lord willing) of my new gas tank. Next run a fuel line.
|
Re: What did you do to your truck today part IV
1 Attachment(s)
Installed the hood I bought from a guy on OfferUp, only to find that the passenger-side is dented, and I'll probably have to remove it to try to bend it back :(
|
Re: What did you do to your truck today part IV
1 Attachment(s)
I patched the passenger side cab corner.
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
2 Attachment(s)
I added some door switches and floor lamps to Frankentruck today. So much nicer being able to see when getting in or out of the truck at night
|
Re: What did you do to your truck today part IV
1 Attachment(s)
I ordered a Summit Trans Jack to help with the transmission switch, made in China, you can almost see the hand sanitzer stains........ It went together very well with no missing parts, even though the box was torn in one corner. The base on the unit is very heavy duty, there are 1/2" bolts under to holds the footing agains the verticle part of the base as well. Although I'm only going to use it once, I split the cost with a buddy who will need it as well, the total was only $175.00 with shipping ($10.00 more due to weight).
We considered renting one for a week but that ran $81.00 so it was cheaper to simply buy it vs. having to pick it up & delivery back to the rental place. |
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
Quote:
|
Re: What did you do to your truck today part IV
1 Attachment(s)
Finished up installing the Street Demon 750 on my 383.
|
Re: What did you do to your truck today part IV
Installed Russell an-6 fuel line today:bann::bann:
It fired up and no leaks (so far). Have not gotten to drive it yet |
Re: What did you do to your truck today part IV
2 Attachment(s)
A few weeks ago I went up with my son and put the rebuilt cross member back in the truck. The calipers would not fit and I remembered I had to do some grinding the last time I put drop spindles in one of my trucks. Went back up and got that all sorted out and was able to get the truck back on the ground. So right now I have a 3" drop in the front with stock springs in the rear. I am sure it will drop down more when I put the engine back it. I also have new springs in the front.
|
Re: What did you do to your truck today part IV
I finished cleaning up the tie rod ends and steering components on the crossmember upgrade to my 66. Since I did use my old 66 crossmember and used the control arms and spindles off of a 79 c10 truck, will the linkage from the 79 work ok without any problems? Also do I need to use shocks for a 66 or a 79? All help appreciated
|
Re: What did you do to your truck today part IV
Quote:
On my green truck I just used later model spindles and on my blue truck I used all of the steering components from a 75. Capt Fab sells a mount for the later steering box if you don't already have one. |
Re: What did you do to your truck today part IV
Mounted power steering box with Captain Fabs adapter. Was able to set idler arm, with help from ideas on this forum. Thanks folks .I didn't weld the adapter. I think it will be fine with just the bolts. Now on to getting power booster bracket (also Capt. Fab product) mounted.
|
2 Attachment(s)
I pulled my bed off and started to sand the exterior of my cab. Never thought I would dig this far into this truck but it has been fun
Posted via Mobile Device |
Re: What did you do to your truck today part IV
What a nice shop! Is your truck red and white or orange and white?
|
Re: What did you do to your truck today part IV
2 Attachment(s)
Got my brake booster and master cylinder installed yesterday. Going to put the proportioning valve & hydraulic clutch MC on today if it doesn't storm.
|
2 Attachment(s)
Quote:
Posted via Mobile Device |
Quote:
Posted via Mobile Device |
1 Attachment(s)
Worked on sanding the cab today and got a little body filler on a couple small dents. Hopefully soon I can throw a coat of primer then some makeup on this pig!
Posted via Mobile Device |
1 Attachment(s)
Finally got her lowered, new...er 71 rear end in, new springs, shock relocation brackets, drop shocks that don’t fit lol...I would ***** and tell you guys that not one bolt has cooperated with me but I know we have all been there. Man, am I glad that’s over!!!🤘
Posted via Mobile Device |
All times are GMT -4. The time now is 12:59 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com