Re: What did you do to your truck today?
 

Outstanding work on the tank install, looks like the factory would have done it Rich!!!!:metal:

Re: What did you do to your truck today?
 

took the cab to the media blaster.welded the outer and inner pass door skins on

Re: What did you do to your truck today?
 

Ordered a power steering box, pump and pump brackets from Marshall Auto Wreckers in Alberta, $90.00 seemed like a killer deal to me. Probably cost another 20-30 to ship it:smoke:

Re: What did you do to your truck today?
 

Thanks for comp..Craig, that the look I was after...more mods to come later.

Re: What did you do to your truck today?
 

Cleaned around it, because I get the first new set of tires, since the build began 3yrs ago, in the morning.
I am excited to get some real rubber on her ("Sally"), my wife named her Sally. She said any thing you spend so much time on must have a name, and it must be a girl to keep my full attention as she has.
Anyway I am going to put new lugs on her in the morning so her new shoes will stay put.
I also removed the tape that was holding the door seals in place while the glue dried.
Posted via Mobile Device

Re: What did you do to your truck today?
 

I took the grinder to the front grille, put the GMC letters on, put the headlights together, put the grille on the truck, took off the mirrors and cleaned them and repainted them... not a bad day!

You can see pics at my build page: http://67-72chevytrucks.com/vboard/s...=1#post5644784

Attachment 997860

Re: What did you do to your truck today?
 

Converted from worn, jamming coloumn shift to a Mr Gasket floor shifter. Went pretty well and took about 3 hours.

Anyone want the old column shift linkage? free for the cost of shipping.

Re: What did you do to your truck today?
 

I am not inrterested in the linkage, but I am wanting to find out how to remove it. I am rebuilding a column, and struggling with the last bit of tear down. The tab between the two linkage arms, is it press fit? welded?

Re: What did you do to your truck today?
 

Can't help you, sorry' I just unbolted the linkages where they attach to the arms on the column and left the arms in place.

Re: What did you do to your truck today?
 

Where did you get the tank?
Posted via Mobile Device

Re: What did you do to your truck today?
 

Put new shoes on Sally;
http://i1326.photobucket.com/albums/...6B86B0D328.jpg
http://i1326.photobucket.com/albums/...6B84BFFE9D.jpg
Posted via Mobile Device

Re: What did you do to your truck today?
 

I installed an interior light with door jamb switches.

Interior light when I got the truck:
http://farm9.staticflickr.com/8189/8...b2443968c5.jpg

Door jamb switches:
http://farm9.staticflickr.com/8329/8...a627968e90.jpg

Installed:

http://farm9.staticflickr.com/8335/8...37feba85e5.jpg

Now I can see:
http://farm9.staticflickr.com/8195/8...c817e57543.jpg

Re: What did you do to your truck today?
 

Well done on the dome light!

That's my plan as well.

BTW, did you tap the holes in the door posts?

Steven

Re: What did you do to your truck today?
 

Re: What did you do to your truck today?
 

I didn't tap the holes. The pins come with a small nut. I drilled a hole slightly larger than the pin threads and then used a washer and tightened it down with the nut.

John

Re: What did you do to your truck today?
 

Just scored both uncut non-rusted inner fender wells and both door glasses for the 66 for $80 from a guy I found on Craigslist. Super nice guy with a really clean 65 that he almost has complete. Turned him onto the forum hopefully he will join.

Re: What did you do to your truck today?
 

Nice job. On my list of things to do as well.

Re: What did you do to your truck today?
 

Fyi – here’s an article on the installation some might find helpful. I followed this when installing my door switches:

http://www.persh.org/pickup/DomeLight.htm

Re: What did you do to your truck today?
 

yep, that is the article I referenced when doing mine. Very helpful.

Re: What did you do to your truck today?
 

Here is a good one for you.
A few weeks ago (ok about 4) I had my truck hooked up to start it. It wouldn't start and I had no spark to the plugs. A friend of mine came down today with his volt meter and we started with the switch and had 12 volts there. Then out to the coil (HEI ignition) and no volts there. I pushed the plug back on the switch and 12 volts popped up. I tried cranking but no spark, the 12 volts went away. My new wiring harness has a fuse for the coil and it blew. Why did it blow.. Who knows..
Took the cap off to make sure the rotor was in there and even turning and it was. Want to make sure the dodad was in the middle of the cap touching the rotor and it was. Finally I pulled the coil to see if make I broke a wire. I never took the coil out of the dist (which is a brand new Mallory) and as soon as I lifted it up we saw that the coil was in upside down. Who ever put the coil in at the factory put it in upside down. I flipped it over sprayed the carb with starting fluid and my truck made that BBC sound through open headers. What a smile I had on my face and then after that I had another friend come down adn help me put the hood back on. :metal:

Re: What did you do to your truck today?
 

very nice... it is the little things isn't it?

Re: What did you do to your truck today?
 

Barely got home from the dump, when I realized my truck was running off of battery.....:waah:

Voltmeter was dead meat....... Seems I may have an older alternator wired into an earlier external voltage regulator that may be prone to failures...... running a 76 SB 350... and I sure would like to convert to an internal VR.


:rolleyes:

Re: What did you do to your truck today?
 

Here, we just beat this to death ....http://67-72chevytrucks.com/vboard/s...d.php?t=546271

Re: What did you do to your truck today?
 

I actually did not do this myself, but I got the wiring done for the headlights and turn signals at a small auto electric shop in mussafah, all working now! Still need some work on the fuel gauge, wipers, and new CD player, and will get to that shortly.

My Truck Build:
http://67-72chevytrucks.com/vboard/s...=1#post5647667

Re: What did you do to your truck today?
 

axle flip on my '66 GMC