Re: Not Another Rebuild Thread....
Quote:
Quote:
:lol: I have the ash tray ready to be reassembled, and realized I had best do some prep work with the dash extension before I weld it up in place. I realized it is going to be a ton easier to do the stereo install prep work with it out of the truck, than in it.... That was almost a :dohh: moment !! |
Re: Not Another Rebuild Thread....
Quote:
|
Re: Not Another Rebuild Thread....
Quote:
|
Re: Not Another Rebuild Thread....
Quote:
Quote:
|
Re: Not Another Rebuild Thread....
3 Attachment(s)
Not a lot "done" that is photo worthy.
funny how a seemingly little thing can take up so much time... Project: hang coat hooks inside cab Time taken: majority of an 8 hour day. This is what I started off with before I tackled the inside of the cab, granted it took a little time to make that metal template, but I was far better taking that time and effort than taking a chance of messing up the inside of the cab (and then having to fix the mess up). These came out of a 69 Eldorado, and there is a roof bow they screw into which my truck does not have, so I made that backing plate. With an anchor screw at the top, (which the coat hook plastic trim covers) it was surprisingly easy to get this unit fished up in there. Some left over welding wire worked perfectly. Attachment 1005345 About 7 hours later... Attachment 1005346 And of course I took it out, leaving the backing plate until after I paint the interior. Then yesterday most of my day was spent in working on my cyclops eye brake light. Since it will share an access hole with my dome light, I figured it was prudent to get it made too. Attachment 1005347 The dome light assembly (I started a new one from scratch again, making this attempt #3) is about done too. Just needs some paint stripped, sanding, and some fill in some of the weld spots. Photos of that are coming. So like I said, not much that is DONE... but getting there. |
Re: Not Another Rebuild Thread....
|
Re: Not Another Rebuild Thread....
Hey McMurphy! I havent really been on the forum that much besides updating my build thread every once in awhile , and havent really read anyones builds in a long time! Like many others you have a giant butt load of pages to read till I catch up ( I have to admit im only a few in on yours still) but I admire what you have done so far and in the freezing cold :lol: Keep it up! and ill get to the end one day! Also you should be receiving package in the snail mail sooner or later i sent it off a couple days ago! Cheers!
I play world of war craft every so often also LOL! |
Re: Not Another Rebuild Thread....
cool build
|
Re: Not Another Rebuild Thread....
3 Attachment(s)
Quote:
Quote:
I had to let my WoW accounts go, the game seriously dead ended at level 85 without a clique of friends to play with, plus the truck taking most my free time. I still have my Everquest tho, and I try to log in at least once a month, go figure.... Quote:
This weekend had a large bite of time taken out of it due to some last minute Army stuff Saturday. After that it was just working on my cyclops eye, and my dome light mods.... Even though I got this mounted up, I am not 100% on it. I may keep trying to make it work, or scrap it and start over. This is it mounted. Attachment 1008202 I picked up a 6volt cube battery for testing wiring, this is the brake light lit up with that, so it isnt very bright (kind of like me....Hmmmm) Attachment 1008203 This is all 3 bulbs lit up. The plan is to get amber bulbs for the left and right, and wire the left and right as turn signals. Attachment 1008204 Other than that I made some pretty awesome progress on the dome light mod, I will be sure to take some photos of that tonight of how I did that. |
Re: Not Another Rebuild Thread....
Quote:
|
Re: Not Another Rebuild Thread....
i really like the light, do you have any pics from left to right to see the angle it mounted on?keep up the good work.
|
Re: Not Another Rebuild Thread....
Quote:
Quote:
|
Re: Not Another Rebuild Thread....
5 Attachment(s)
Sorry Flips I decided my first cyclops light mount was not what I wanted, so I have redone it.
I also decided to make more progress on my cab starting with the ceiling down. I was doing fine and had the ceiling looking perfect when I shot some new paint and I got the horrendous lifting, cracking, and peeling. I about lost my mind. After a full day of trying to fix the afflicted areas and wasting more and more paint, I just bit the bullet and stripped the entire ceiling and started back at scratch. The CB antenna hole is not as perfect as it was when the paint decided to screw with me, but if you dont know it is there, you wont see it.... and that is good enough at this point. So this weekend I re-fabbed my cyclops mount, got the ceiling repainted, and started on the side panels for console section of the dash extension. But before I could get too far into that, I knew I had to make an extension for the heater. So that is what got "done" today !! After I cut it out of the donor sheet metal, I marked it with all the measurements someone would need to recreate it. In retrospect though the far right tab marked "optional" I would move to the bottom 2 3/4" panel and used it to screw into the heater control box. You will see what I mean later. Attachment 1011691 This is it all assembled; this will be the cabin side of the tube. Attachment 1011692 This is the firewall side. Attachment 1011693 This is the driver side end. I am hoping the little flap will help blow the warm air down so I wont get captured up under the dash too much. I am also hoping that the length will keep it from roasting my gas pedal foot !! Attachment 1011694 |
Re: Not Another Rebuild Thread....
2 Attachment(s)
Here I am just holding it up....
The reason I would have put the optional tab on the top is the back side mounting screw is impossible to get to without taking the whole box out. I like things simple, and that does not qualify !! Attachment 1011696 Here it is mounted up. Attachment 1011697 Now it is drying from fresh paint... in the next few days I will put it up in for good. Without this extension for the heater, the driver side would not get any heat or my console would get filled with heat and probably cook the radio I am going to mount up in there. |
Re: Not Another Rebuild Thread....
Great idea, that's going to make a huge difference.
|
Re: Not Another Rebuild Thread....
Quote:
I hope. :mm: |
Re: Not Another Rebuild Thread....
sorry to hear about your ceiling man those things got problems i wanted to cry when mine started cracking and peeling! and i love the heater tube i thought about something like this but never got around to it how the heater is normally seems to work pretty good but i bet that makes a huge diff!
|
Re: Not Another Rebuild Thread....
that is cool ..i always hated cold left foot
|
Re: Not Another Rebuild Thread....
Makes me think of the quote, "Necessity is the mother of invention!" Great Job Man!!!
|
Re: Not Another Rebuild Thread....
3 Attachment(s)
Quote:
Quote:
Quote:
Attachment 1012181 These next two show the sides of the console, which will have removable panels and will house/mount 2 of my stereo speakers. Attachment 1012182 Attachment 1012183 PS.... I was just kidding about the grenade launcher. Those freekin rounds are expensive !! |
Re: Not Another Rebuild Thread....
ejaculatiton seat now thats what im talkin about!!! Oo... wait ejection seat... just kidding man that looks sweet dude i love it your giving me ideas man!
|
Re: Not Another Rebuild Thread....
"Here will be mounted my stereo, and odd and ends like the cigarette lighter, fog light switch, ejection seat button, flame thrower, oil slick, and grenade launcher and other stuff....."
Brings back memories of the show "CHiPS" with Ponch & John the motorcycle cops. In one episode they had to chase down a movie car with all those things. During a chase the car made an oil slick. The machine guns were fake though. Bet all your stuff will be real and kick a$$. Im going for a cloaking device myself.:haha: I like your heater extension along with the vent cables. The e-brake change over from the knee smacker is my favorite so far. Great idea.:metal: |
Re: Not Another Rebuild Thread....
Some very cool and inventive ideas....i like it.
|
Re: Not Another Rebuild Thread....
oh...glad you got your cab vents in...Looks great
|
Re: Not Another Rebuild Thread....
Some nice tin-bending!
....Still watchin daily. |
All times are GMT -4. The time now is 10:06 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com