Frozen Bleeders
 

This is a common problem, the solution is fairly simple :

Right after you spray the next shot of penetrating oil on the threads, *SMACK* the bleeder screw dead on with a hammer, the shock will wick the penetrant in and loosen the threads .

If you smack it off center or sideways, you'll snap it off so pay close attention here .

I'm sure you already know to only use a SIX POINTED tool on any bleeder valve ! .

Re: What did you do to your truck today? Chapter II
 

^^^ yep, they come in real handy.. had this fully welded hoosier about 25 years..

stripped and repainted several years ago with clark forklift hot yellow green so I can't lose it..

welded a handle bar on the mast with bycycle hand grips to make it easier to steer..

got a 12vdc 1gal barnes hydraulic power unit for it, just haven't hooked it up yet..

that D60 is about 500lbs, good portable hoist made short work unloading it recently..

https://dl.dropbox.com/s/0e558p0s3vy..._3180.jpg?dl=0

Re: What did you do to your truck today? Chapter II
 

:lol: Words you never want to say around me. I could snap it off even using a plastic Playskool hammer.

Re: What did you do to your truck today? Chapter II
 

I think they were being funny. C10 is the designation for Chevrolet. 1500 would be the "correct" designation for a 1/2t GMC.

I too have a 70 GMC 1500. Welcome to the club. That is a beautiful truck you have there.

Re: Frozen Bleeders
 

Actually, the one bleeder cooperated very easily. The other resisted firmly, so I switched to the line fitting, and it loosened without much trouble at all. and, oh yes: 6-pt box end or socket--absolutely!

I've got some pedal but not as much as I want, so there will be more bleeding in the near future. I would have done some more today, but the test run got everything hot, and I didn't want to crawl back under that way.

The last time I replaced the MC, I had to replace one of the short steel lines between the MC and the distribution block, and the replacement didn't survive the removal, so we had to drive into town to pick up a replacement for the replacement.

I tried to knock the little adjustment slots out of the new drums, but the stamping wasn't deep enough, and the punch just distorted the metal rather than knocking it out. I may go to the trouble of drilling, but not till Fall ;-)

Re: Frozen Bleeders
 

I can tell you that every Dremel tool I have ever bought and worn out has paid for itself 100 times over. I've cut the bearing races off of spindles and then polished 'em enough to get a new bearing on, for example. Food for thought.

Brake Pipe Service
 

I hope everyone here knows what a 'Flare Nut Wrench' is ? .

Very handy (mandatory for me) when loosening up brake pipes even when not rusty .

I grew up Down East and learned the hardest way possible on rusty old junk .

? Did you ever try the "Stick Trick" ? .

It's a simple thing a BMC Engineer taught me, when you're done for the day you wedge a stick (or whatever) between the brake pedal and seat, steering wheel, etc., etc. .

What this does is : partially depress the master cylinder so the by pass port is open ~ then ever so slowly remaining air bubbles (if they're not too big nor plentiful) will in time, work their way out via the uncovered by pass port .

You have to leave it at least 24 hours, often this is the last thing to get that rock hard brake pedal again .

Re: What did you do to your truck today? Chapter II
 

You can do the same thing by pushing the pedal down just a little, and pumping it. I worked for a guy right after I got out of the Navy who showed me that gem. We had a power bleeder, and I preferred to use it to completely purge the system of fluid when I changed a master cylinder, but this cheapskate would do this "mini-pumping" instead. He would do it while I went off to other paying work, so I couldn't complain too much about it. Of course, the master had been properly bench bled first.

Re: What did you do to your truck today? Chapter II
 

installed brake and fuel lines, everything hooked up and in final resting place. Bled brakes. Ran wires to the corners for lights, etc.

Re: Brake Pipe Service
 

I keep a piece of 1 1/2" PVC pipe, with the end wrapped in towels, for this purpose, hanging on the wall.

Re: What did you do to your truck today? Chapter II
 

I have to say I have never heard of the "stick" procedure. How far do you move the pedal down?

The Stick Trick
 

I've had good results anywhere, the main thing is to move the MC's internal piston sufficiently to uncover the bypass port .

I like to apply some pressure so push the brake pedal down as far as you can then wedge the stick in place or move the seat forward until the stick is held in place .

As mentioned above, clean and clear brake fluid is very important, flush the entire system any time you see brown or black fluid .

FWIW, this simple thing works amazingly well on Motocycle front disc brakes too, just use rubber bands on the brake lever over night .

Re: What did you do to your truck today? Chapter II
 

First piece of the puzzle finished, reground .010/.010 under and looks perfect. I was so happy I smoked some sausages and the smoked pickled eggs are the bomb. I'm never making non smoked again smoked eggs all the way. Had to do some touch ups where I scratched the fire wall, a bit of paint now.

Re: What did you do to your truck today? Chapter II
 

Finally on to final assembly of the front suspension. Going to push in the bushing shells and put the front end back together.

Re: What did you do to your truck today? Chapter II
 

I moved it outside , been in the garage 2 years. It's running great, now the body and paint begin!

Re: What did you do to your truck today? Chapter II
 

Couple more!

Re: What did you do to your truck today? Chapter II
 

Received my bed floor kit from Larry ((GR8-68)) for my 72 super project....beautiful workmanship from this man..had him finish both sides and predrill so its ready to go.

Re: What did you do to your truck today? Chapter II
 

Installed Sound Deadener and new carpeting in the cab then took the wife out for a drive.

Bill

Re: What did you do to your truck today? Chapter II
 

installed new exhaust isolators and put hangers in. Have to wait on middle isolators til tomorrow

Re: What did you do to your truck today? Chapter II
 

Got the behemoth rear bumper off today and the aftermarket 4 ft long hitch cut out. It's getting there.

Re: What did you do to your truck today? Chapter II
 

Thanks Rob, glad to see another pleased customer, can't wait to see pics of it installed :chevy:

Re: What did you do to your truck today? Chapter II
 

Got the stock drivetrain out and took the bed off. Lost the original timing chain at 99,996 miles. No compression. Have a 5.3/4l60e on the way and moving tank under the bed

Re: What did you do to your truck today? Chapter II
 

painted my tail gate today.....

Re: What did you do to your truck today? Chapter II
 

...

Re: What did you do to your truck today? Chapter II
 

Replaced the fan clutch a couple of weeks ago. Took it and ran it at 65 MPH up a long steep freeway grade that we have here. Got to 220º going up, and dropped to 205º on the way down. Cruising in town coming back home, it held right about 205º. I'll drain the radiator down far enough to check the tubes for crud. I have a 7-mile jaunt scheduled for a camp out close to home, to check it out further, and I won't be driving that fast- with the trailer it'll not be over 55- and some of the road is posted for 45 MPH. It ought to be running a little hot, when the air temperature is still over 110º. All this is with a 190º thermostat.

I'm up in the air whether to rod this one (if that is all it needs), as it is a 4-row brass job, replace it with the same, or get an aluminum radiator. Any one know off hand if the aluminum radiators are a direct fit? I've seen some pics of modifications being required to the radiator hose connections.