Re: 1971 c10 stepside
Raul it's the same as a lsa. The idler pulley above the compressor is almost in the same place as the superchaeprger pulley. I went and measured my buddies ctsv today to get some dimensions. Just FYI. They were at least super close measuring with a tape measure inside the car.
Posted via Mobile Device |
Re: 1971 c10 stepside
Quote:
|
Re: 1971 c10 stepside
Keep up the good work. Need some new pic's. I know you've been busy doing something.
Posted via Mobile Device |
Re: 1971 c10 stepside
Quote:
Posted via Mobile Device |
Re: 1971 c10 stepside
Good deal. Family is important even if it hurts in the morning. We can't keep up like we would like but it's hard to admit it.
Later Posted via Mobile Device |
Re: 1971 c10 stepside
whats up just making sure I get subscribed to this one! waiting for pics....
|
Re: 1971 c10 stepside
Quote:
thanks !!!!! |
Re: 1971 c10 stepside
Happy birthday Brother!!!!
|
Re: 1971 c10 stepside
if congrats are in order then CONGRATS on getting......OLDER !!!!!!!! Happy Bday !
|
Re: 1971 c10 stepside
4 Attachment(s)
some small updade !!! back on post #559 i started the mounting of my air tanks and some of you pm me asking what about the cross rails for bed , i will post some pix of what i had in mind , i have two ideas on how to raise my floor but im still undecided , what i did was i cut a small piece at each corner of bed to have access to slide and weld the new frame , build a frame around the bottom of the original area where the wood would normally go that way it will serve as the base , the bed will be solid and 4 bolts will be all you to loose to remove the bed in the future , i will use only two braces , one up front and one out back , i reinstalled the bed and it is very solid , squared and now it follows the cab lines straight across , the new base side bars and the rear towards the cab will also now serve me as a pivit point for my floor future plans , some gaps now have to be filled so a lot of work still to to in the bed area
|
Re: 1971 c10 stepside
Quote:
Quote:
|
Re: 1971 c10 stepside
pivot points....TILT BED ?
|
Re: 1971 c10 stepside
Quote:
|
Re: 1971 c10 stepside
shoot tilt the whole thing sure makes it easy to clean and work on anything underneath....me a my grandfather were the mini-truck tilt bed kings in this area !! LOL we built a bunch of them, back in the day !
|
Re: 1971 c10 stepside
Quote:
raise the bed floor a couple inches for pumpkin clearence and then do a wood bed on hinges and actuators. Throw the gas fill in the area you raised that would be hidden when the tailgate is shut. |
Re: 1971 c10 stepside
Quote:
Quote:
|
Re: 1971 c10 stepside
|
Re: 1971 c10 stepside
LOL...oh YA !
|
Re: 1971 c10 stepside
1000+ hp. AND a dancing bed? Im thinking you might want to put grade8 bolts in yours to make sure it stays on! I cant wait to see and hear this truck running..
Posted via Mobile Device |
Re: 1971 c10 stepside
Quote:
|
Re: 1971 c10 stepside
2 Attachment(s)
today i cut ot the holes for the ac vents , finished stripping the rest of the cab , all that's left is the front and back glass , ill be running some elctronic accessories , i dont want to be drilling a nice clean firewall so i welded a couple of small braces across the under dash for future wire routing and also a place to hang any relays or any electrical accessories, one is just an angle , the other i used a flat rod and i welded 1/2 inch spacers to separete from firewall for screw clearance , also some one had butchered the doors for some speakers so i took care of that too,
|
Re: 1971 c10 stepside
4 Attachment(s)
more pix
|
Re: 1971 c10 stepside
That's some good progress on your birthday. Keep it up. Happy Birthday buddy.
Posted via Mobile Device |
Re: 1971 c10 stepside
Quote:
|
Re: 1971 c10 stepside
Nice
Posted via Mobile Device |
All times are GMT -4. The time now is 10:09 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com