The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)

- Squarebody Projects and Builds (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=139)

- - my 80 build (https://67-72chevytrucks.com/vboard/showthread.php?t=283326)

thanks 1984, it should be a 6" drop, It has djm 3" spindles and 2" coils but it only turned out to be a 4" drop

Yesterday I got the gauges wired up on cluster, would of got the indicator, and dash lights wired up and that would of been done, but my parts from summit came so had to look at them and installed the water pump pulley and the window crank handles would installed the crank pulley but it looks like I have to get shorter belts, and a guy came over to buy a few parts and he admired my truck for about hour,

Ive done a few things on my in the past couple of days made some kick panels out of some galvanized steel, wired up a 12 volt outlet and installed three inch drop springs, and the top of the wheel well measures 24 3/4 inches before I started it was about 27 inches, I'll take pics tomorrow

Looks great flamingbig10!!! Those couple extra inches taken away made a big difference in the stance. Joe

thanks, the coils helped the appearance a bunch, it looked kinda goofy before

trucks like yours make us all proud

good work > great looking

:metal:

Wow! Only 18! I am 23 and haven't done near as much as you have. Looks good! I especially like your dash. Its similar to what I want to do

thanks 85, I used the factory pieces as templet, a lot people don't believe that how young I am that I built my truck

Truck looks great! keep up the good work!

Thanks Alex, today I used Mothers California Gold® Clay Bar System, what A difference it made the finish hasn't looked this good in over two years, now I need to use the 3 step Ultimate Wax System

Nice! I like the interior trim, good job.

I figured out why my wipers would only work on slow had a bad ground, I was Tired of hiting my knee on my radio so I moved it where the factory a/c controls, then I drove my truck it was a liitle ocword with the shifter lever, so I decided to leave it alone, until I know what I really want. I was given a 89-91 bezel that I used since past owner messed up the metal dash were the radio was since I didn't notice it when my truck was getting body work, I mad a piece of diamond plate that covered up the radio opening just didn't take any pics
this was before it was tightened down
http://i147.photobucket.com/albums/r...0/IMAG1454.jpg
also took a bunch of pics of my heater under the dash
http://store.summitracing.com/partde...5&autoview=sku
http://i147.photobucket.com/albums/r...0/IMAG1462.jpg
http://i147.photobucket.com/albums/r...0/IMAG1459.jpg
http://i147.photobucket.com/albums/r...0/IMAG1458.jpg

Awesome work. Would it be possible to update some of the old pics that aren't showing up?

Nice pics!:metal:

Good luck with the upgrades and keep us posted!

thank's guy's I sure can

Over the week end I relocated my battery to bed and installed my amp in my truck, wile I was at it I cleaned the carpet, and ordered a flamed etched mirror from lmc
today, my driver side door panel was finished
http://i147.photobucket.com/albums/r...0/IMAG1512.jpg
http://i147.photobucket.com/albums/r...0/IMAG1513.jpg

Welcome to the club;)

That dose look sweet! Good work!! Now how do you like them?