Re: New project
Quote:
I also had everything to build a 4.11 center so it is in the diff shop . I tried to set it up myself but didn't feel great about the pattern so i took it in to have it double checked . Seriously considering moving to 1350 u-joints as i currently have 1330s . Also planning on moving the new rear cell , bottle and battary all the way back to the tailgate . Anyway here are some progress pics of last weeks work . http://i47.photobucket.com/albums/f1...207_200735.jpg http://i47.photobucket.com/albums/f1...207_200715.jpg |
Re: New project
The 1350's is a good call.
I never broke the 1330's I had in my 4100lb truck on a T-brake. I did swap to the 1350's once I got some real tire under it. I like the C-16 cell being up front. Less work the pump has to do. I think it helps fight against the G's on the launch and the run down Broadway. Good luck on your shake downs. |
Re: New project
Quote:
I also took the -4 elbow and on the threaded side i drilled and tapped it for a Holley jet . I took the smallest brass holley carb jet i had and soldered it up then drilled a .042 hole in it . That runs through braided line back to the top of the cell . This is a return line to keep the regulator from "creeping" . I am hoping to keep the fuel pressure steady . Some say run return lines others say don't . Hope i didnt go to big on the hole i drilled . |
Re: New project
If any thing it might be to small. I'm sure it will work.
I ran a race pumps fuel pump and reg. I believe it had a 71 Holley jet in it. I personally like return lines. Keeps fuel psi steady and the temp cooler. Posted via Mobile Device |
Re: New project
Looks like my run without bars is over . Just put $500 down for the materials , Chromemoly 12 point .
|
Re: New project
Are you having someone local fab the cage?
|
Re: New project
QUOTE=Captainfab;5195589]Are you having someone local fab the cage?[/QUOTE]
Yes , there is a guy here in Baytown that has a chassis shop . I went in on a big tubing order with another guy , so we got a break in the price . I want to say $5.30 a ft . X 70 Ft . It will come with the documentation from the manufacterer for the chassis cert . Which will be done at the chassis shop before i pick it up . This is so the inspector can tell the chassis guy directly if there are any problems . I did Mild in the last truck and it's cheaper to do it right the first time . Plus it adds value to the truck to have Chromemoly certed cage . Looking at a 12 point with 2 swing out bars . I will post picks as im going through the build . He has to 25.2 a Nova before me as they are trying to get to the Goergia race . |
Re: New project
Went a few rounds in Baytown todat 1/5th mile bracket race . 7.001 off the trailer . on motor
http://i47.photobucket.com/albums/f1...219_194107.jpg |
Re: New project
Pulled the th 350 today 400 is in . Have to mod the cross meember and add a driveshaft loop while im there . Need new drive shaft yoke so 1350 it is . I had a 1350 rear yoke , so ill have a new shaft made . going 4.11 .
Man was getting the 400 in a pain . |
Re: New project
2570 after the last pass . guessing the bars will add 100#s . Thinking i can put coilovers in place of the front shocks and lose the torsion bar crossmember and bars to get back down their . Also Having some idle curcuit problems with my speed demon so i bought a bigs stage 5 750 for it .
|
Re: New project
wow,, 7.0 to the 1000' mark is kicking right along!!!! NICE job!
|
Re: New project
If you dont mind can you take a few more pics of the fuel and lines , regs up front?? I am at that point and working around a few ideas but to see a few always is a big help. I have that Comp dual cheater kit I am getting into place. On the fuel cell are you running a say -8 TEE with a ball valve to swap from one tank to the other?
|
Re: New project
nice progress!!
|
Re: New project
Quote:
Quote:
Quote:
|
Re: New project
Pic update . Caltracs on , new hood painted , rear fenders painted 1 installed . Swapped to 4.11 . TH400 with transbrake is in .
http://i47.photobucket.com/albums/f1...303_191207.jpg http://i47.photobucket.com/albums/f1...304_151823.jpg Golf cart getting painted and ready for this season of racing . http://i47.photobucket.com/albums/f1...302_150803.jpg http://i47.photobucket.com/albums/f1...302_150824.jpg http://i47.photobucket.com/albums/f1...302_150813.jpg |
Re: New project
|
Re: New project
Looks good :thumbs:
I noticed your CalTracs front brackets are on the ourside of the front spring hanger. Was there not enough room between the spring and the hanger? Do those new rear fenders have a larger opening? I see the flare, but they look like they have a bigger opening. |
Re: New project
Quote:
The rear fenders are wider and will give me 1 1/2" more tier room . I think they were originally off a courier ( so i was told ) , but could have been off a full sized truck . They are glass and lighter than the gray ones . |
Re: New project
i recognize those endmill markings for dishing the pistons. nice work. subscribed....i'd like to see more of this.
|
Re: New project
Just got the pics of the finished golf cart . Let me know what you think .
http://i47.photobucket.com/albums/f1...ejpeg952_2.jpg http://i47.photobucket.com/albums/f1...ejpeg952_4.jpg http://i47.photobucket.com/albums/f1...ejpeg952_6.jpg http://i47.photobucket.com/albums/f1...ejpeg952_7.jpg http://i47.photobucket.com/albums/f1...ejpeg952_8.jpg |
Re: New project
http://i47.photobucket.com/albums/f1...306_184222.jpg
Here is a update . Still no chromemoly , but scheduled again tommorow . I have 16ga. panels being made for the holes or gaps that will have flats to bolt to the fenders and 90's to bolt to the bed floor and a 90 turned in at the back of the cab for looks and strength . They will be painted to match yellow . Have not figured out what to do under the tail lights other than steel brake line for braces to keep everything firm . Still need a fiberglass or small rear bumper to cover the frame rails in the back . The cowl is and Ebay $75 38 inch scoop that was trimmed and added with the 2 part panel bonding adhesive/Epoxy . I was told that if you leave the proper amount of epoxy instead of forcing the scoop to touch the metal hood the all three materials could expand and contract without the seams cracking due to temperature change . Im happy with the job . Got the new driveshaft being built and will pick it up monday . This one is 3.5 inch with 1350 spicer u-joints . Driveshaft loop is in , as is removeable crossmember . The cross member became manditory with the th400 . I also bought a pair of ET streets . These are the 28 x 10.5 x 15 . Basically the old 28 x 9 slick with some grooves cut in to it . I was having a bit of trouble with the drag radial as it was kinda hit and miss . Truck went 1.40 on 29 x 9 Hoosiers so i ought to be able to make it work on a 28 x 9 with Caltracs and Ranchos . I also took 4 drgrees of nose down out of the pinion angle . I am at 3.5 negative . Which sould move to around 1.5 to 2 when i drop the button . I will start with a radial and if need be move to the bias ply as a last resort . I also swapped the rear end gear from 5.00 to 4.11 . this along with the swap from 2.52 ( th350 ) to 2.48 (th400) first gear will take mechanical advantage away help the tire . Removing gear and an adjustible instant center with Caltracs should allow me to dial it in . Probably end up letting go and pulling second to bring it back down . First race of the season is the 17th so we will see . Working hard to get it inspected tuesday . Maybe the rain will stop by then . I also bought/built a fuel flow gauge so i can "creep up" on my tune up . Bracket race rained out this weekend and i needed the test time . |
Re: New project
ready for saturday.
http://i47.photobucket.com/albums/f1...313_131921.jpg |
Re: New project
Ended up testing tonight to try and work out some bugs . Fisrt pass with the 2 step set at 3200 and low bottle pressure . It rolled up on the back tires then tore the threads off the u bolts . I had to much in the driverside bar so it tried to move left . thinking im 2 or 3 clicks soft on the rears . It bit hard enough on a drag radial to tear up hardware so i guess im headedin the right direction . Someone said it had 3 in the air and they had a picture . Here are a few random pics .
http://i47.photobucket.com/albums/f1...1951344096.jpg http://i47.photobucket.com/albums/f1...1951363149.jpg |
Re: New project
Truck looks like it is coming along great! Look forward to seeing it run once ya get the kinks worked out. Mine should be back together in 5 or 6 weeks. Might bring it out to Baytown one weekend to play a bit.
Jay |
Re: New project
Wrenches flyin around here . tryin to get it back together today . gates open at 3 . Gotta go .
|
Re: New project
Runner up 6.25@110 then a 22 mile cruise to prove it is a street car . Pretty good night .
|
Re: New project
Found ths video of the finals . Spun bad for the loss . Mostly of him .
http://youtu.be/4FWKO11QgIs |
Re: New project
Was that Mustang Billy you lined up against? Sure looks like his car but I dont remember him having stickers on the back glass. Anyway looks like you were moving right along once you hooked up. BTW the right lane at HMP is terrible from my exprience.
|
Re: New project
The right lane was hit and miss . Promod guys were trying to take power out , then add a drag radial and the weight challenges of a truck , well . Yes right lane wasn't my friend . Billy and i in the final . Good guy . We were side by side in one qualifying run .
|
Re: New project
The ladder shook out me and a SN95 turbo car in the semis . We took the bottle and heated it up pretty good as i was a touch rich on the nitrous fuel pressure . It looked like we had the turbo deal covered on motor so we were experimenting to see if we could trim some Et . The turbo car didnt make the call and nither did the second set , so instead of a competition by rounds for me and the other guy they put us in the finals right there . I ended up spinning and he ran slower also . Had a good time anyway .
|
Re: New project
Round 2 of qualifying .
http://youtu.be/wLo0JwUC9oE |
Re: New project
Dropped it off today at the chassis shop for the bars . I'll get pics coming up as the cage progresses . Does anyone even check this thread ?
|
Re: New project
Well , i dropped it off today . I had paid for the tubing already and was in line after Lamar's Nova to have a bar done . My wife convinced me it need to be done for safety reasons . 12 point Chromemoly cage custom bent and tig welded . Certified to 8.50 with swing out and removable door bars . This will add 77# to the truck . It will be installed so later if i decide it can be removed and the truck cab will not be cut up . The bars will also have motor plate tabs hidden behind the fenderwells . Room for coilovers if i decide to remove the torsion bar stuff , yet retain the stock suspension and get m 77#'s back .
|
Re: New project
Yep, I check it everyday :)
Looking forward to the pics...... Quote:
|
Re: New project
I check it often myself.... who did your drive shaft? I will need a new one if I can ever get my truck back together!
|
Re: New project
Quote:
http://i47.photobucket.com/albums/f1...322_125953.jpg Quote:
|
Re: New project
I check in and looking forward to seeing the finished cage. I have a bud with a 6.0 ls luv that runs 10 tens on motor, 275 radial sweet rides!
|
Re: New project
Quote:
|
Re: New project
Mostly a pic update ,, but i want opinions . More eyes are better .This is not a cheap venture an i want it to be as correct as possible . Im happy so far . We couldnt go through the dash due to the weird angles so we went around . let me know what you think .
http://i47.photobucket.com/albums/f1...327_173722.jpg http://i47.photobucket.com/albums/f1...327_173708.jpg http://i47.photobucket.com/albums/f1...327_173618.jpg http://i47.photobucket.com/albums/f1...327_173559.jpg http://i47.photobucket.com/albums/f1...327_173541.jpg |
Re: New project
Should be out monday pics coming .
|
All times are GMT -4. The time now is 01:50 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com